PuzzleSounds DR. Q ENVELOPE FILTER Manual de usuario

DR. Q

ENVELOPE FILTER

DR. Q ENVELOPE FILTER

We hope you enjoy your new Dr. Q! In this manual, you will find

documentation and guidelines helpful to put it together.

Here we have put together a few links that detail some of the aspects

explained in this manual and that we think you can find helpful:

Kit & PuzzleKit general manual

Reading resistor and capacitor values

Also, in our blog you can find multiple articles regarding tips for

soldering, more in-depth posts about resistors and capacitors…

Check it out!

DR. Q ENVELOPE FILTER

Bill Of Materials

Resistors (14)

R1, R2, R11, R12, R15

47k

3.3M

22k

220

10k

R8, R9, R10

470k

R13

100

Capacitors (9)

C1, C3

10n

22u

(electrolytic)

100n

C5, C6

4.7n

C8, C9

47u

(electrolytic)

Transistors (1)

1 Q1 2N3904

ICs (1)

1 U1 TL072

Potentiometers

1 ATTACK 1kB (lin.)

1 RANGE 20kB (lin.)

1 SENS 100kB (lin.)

Other (2)

2 L1, L2 LED 5mm (red)

1 DP 1N4007

1 RON 1k

DR. Q ENVELOPE FILTER

Part Placement

DR. Q ENVELOPE FILTER

STEP BY STEP GUIDE

STEP 1 –Resistors and diodes

Place the resistors and diodes. If you have

troubles reading the values, check out our

“Reading Part Values” tutorial.

Resistors (14)

R1, R2, R11, R12, R15

47k

3.3M

22k

220

10k

R8, R9, R10

470k

R13

100

Other (2)

1 DP 1N4007

1 RON 1k

STEP 2 –IC sockets & Pin header

First of all place the IC sockets (without

the ICs). Pay attention to the orientation!

The small notch in the socket should be

oriented as indicated in the PCB.

Then, connect the 6 pin header:

STEP 3 –Capacitors and Transistors

Solder the capacitors and transistors. If you have

troubles reading the values, check out our

“Reading Part Values” tutorial. Pay attention to the

orientation, as well as to the polarity for

electrolytic capacitors.

Capacitors (9)

C1, C3

10n

22u

(electrolytic)

100n

C5, C6

4.7n

C8, C9

47u

(electrolytic)

Transistors (1)

1 Q1 2N3904

STEP 4 –LED and Battery Clip

Solder two wires to the LED

connection (red to the “+” sign).

Then, solder then to the LED (the red

wire is connected to the longer pin).

Solder the battery clip, connecting the red wire to the “+” sign:

STEP 5 –DC Power Jack wires

Solder three wires (about 5cm each) to the DC connection as shown (don’t solder

anything to the other end yet!):

Tabla de contenidos

Otros manuales de Pedal de música de PuzzleSounds

PuzzleSounds

PuzzleSounds SFT DISTORTION Manual de usuario

PuzzleSounds

PuzzleSounds RC Booster Manual de usuario

PuzzleSounds

PuzzleSounds CENTAUR OVERDRIVE Manual de usuario

PuzzleSounds

PuzzleSounds DOD 250'77 Overdrive Manual de usuario

PuzzleSounds

PuzzleSounds GREEN RINGER Manual de usuario

PuzzleSounds

PuzzleSounds FIRE RED FUZZ Manual de usuario

PuzzleSounds

PuzzleSounds Tubesreamer Manual de usuario

PuzzleSounds

PuzzleSounds DEEP BLUE DELAY Manual de usuario

Manuales populares de Pedal de música de otras marcas

Behringer

Behringer ULTRA WAH UW300 Manual de usuario

Whirlwind

Whirlwind oc-bass Manual de usuario

Strymon

Strymon Lex-rotary Manual de usuario

Behringer

Behringer PB600 Manual de usuario

Lexicon

Lexicon MX200 Manual de usuario

Dunlop

Dunlop Hendrix 68 Shrine Octavio Fuzz Series Manual de usuario

Matthews Effects

Matthews Effects Whaler V2 Manual de usuario

Grid 1

Grid 1 Pedal Jeanie Manual de usuario

Amptweaker

Amptweaker tightboost Manual de usuario

Ibanez

Ibanez TS-808 Tube Screamer Overdrive Pro Manual de usuario

BYOC

BYOC Analog Chorus Manual

Dimavery

Dimavery EPVP-50 Manual de usuario

Tefi Vintage Lab

Tefi Vintage Lab GEGÈ Manual de usuario

Pro-MIDI

Pro-MIDI G25 Manual de usuario

DW 7000 Manual de usuario

FAMC

FAMC Liquid-Foot Jr. Series Manual de usuario

Dimavery

Dimavery EPOD-50 Overdrive Manual de usuario

TREX

TREX ToneBug Totenschläger Manual de usuario