DFI G586SP Manual de usuario

G586SP

G586SPAIO

Rev. 0+

System Board

User’s Manual

-D29160226-

No part of this document may be copied, reproduced in any

form, or by any means or used to make any transformation/

adaptation without the prior written consent of DFI, Inc.

DFI, Inc. makes no warranties with respect to this documen-

tation and disclaims any implied warranties of merchant-

ability, quality, or fitness for any particular purpose. The

information in this document is subject to change without

notice. DFI, Inc. reserves the right to make revisions to this

publication and to make changes to any and/or all parts of

its content, at any time, without obligation to notify any

person or entity of such changes. Further, DFI, Inc. assumes

no responsibility for any errors that may appear in this

document.

DFI is a registered trademark, G586SP and G586SP AIO

are trademarks of Diamond Flower, Inc. All other product

names mentioned are trademarks or registered trademarks

of their respective companies.

vFCC Statement on Class B

This equipment has been tested and found to comply with the

limits for a Class B digital device, pursuant to Part 15 of the

FCC rules. These limits are designed to provide reasonable

protection against harmful interference when the equipment

is operated in a residential installation. This equipment

generates, uses and can radiate radio frequency energy and,

if not installed and used in accordance with the instruction

manual, may cause harmful interference to radio communica-

tions. However, there is no guarantee that interference will

not occur in a particular installation. If this equipment does

cause harmful interference to radio or television reception,

which can be determined by turning the equipment off and

on, the user is encouraged to try to correct the interference

by one or more of the following measures:

•Reorient or relocate the receiving antenna.

•Increase the separation between the equipment and

the receiver.

•Connect the equipment into an outlet on a circuit

different from that to which the receiver is connected.

•Consult the dealer or an experienced radio TV

technician for help.

Notice:

1. The changes or modifications not expressly approved by

the party responsible for compliance could void the

user's authority to operate the equipment.

2. Shielded interface cables must be used in order to

comply with the emission limits.

vTableofContentsv

Introduction................................................................................6

FeaturesandSpecifications.........................................................7

PackageChecklist .....................................................................9

InstallationOverview.................................................................. 10

PreparingtheArea.................................................................. 10

HandlingtheSystemBoard....................................................... 11

TipsinHandlingtheSystemBoard......................................... 11

HardwareInstallation............................................................... 12

BoardLayout ..................................................................... 13

MemoryInstallation............................................................. 14

InstallingtheModules..................................................... 16

JumperSettings................................................................. 17

CacheConfiguration............................................................ 21

CPUInstallation................................................................. 23

InstallationProcedure..................................................... 24

ClearanceRequirements................................................. 26

FanExhaust ................................................................. 26

Built-inPorts...................................................................... 27

SerialPorts................................................................... 27

PS/2MousePort............................................................ 28

ParallelPort .................................................................. 28

FloppyDiskDriveController.............................................. 28

ConnectingtheFloppyandHardDiskCable.............................. 29

ConnectingtheFloppyDisk.............................................. 29

ConnectingtheIDEHardDiskInterface............................... 30

AddingaSecondIDEHardDrive....................................... 31

PreparinganIDEDriveforUse.......................................... 31

InstallingExpansionCards........................................................ 32

SoftwareInstallation................................................................. 32

TroubleshootingChecklist........................................................... 33

AwardBIOSCMOSSetupUtility................................................... 34

StandardCMOSSetup............................................................. 35

BIOSFeaturesSetup............................................................... 38

ChipsetFeaturesSetup............................................................ 39

PowerManagementSetup......................................................... 40

PCIConfigurationSetup........................................................... 41

LoadBIOSDefaults................................................................. 42

LoadSetupDefaults................................................................ 42

PasswordSetting.................................................................... 42

IDEHDDAutoDetection........................................................... 43

HDDLowLevelFormat............................................................. 46

Save&ExitSetup................................................................... 47

ExitWithoutSaving.................................................................. 47

System Error Report................................................................. 48

AppendixA:AwardBIOSHardDiskTable....................................... 52

AppendixB:Memory&I/OMaps................................................... 54

AppendixC:PCII/OPinAssignments............................................ 56

AppendixD: ISAI/OPinAssignments........................................... 57

AppendixE:SystemOverview...................................................... 58

AppendixF:ConnectorPinAssignments....................................... 61

AppendixG:VGAMPEGSupportModeList.................................... 72

G586SP/G586SPAIO

vIntroduction

The G586SP/G586SP AIO system board offers several

advanced features integrated into the system board. Its

design is based on the new Peripheral Component Intercon-

nect (PCI) local bus and Industry Standard Architecture

(ISA) standards.

The G586SP/G586SP AIO system board provides a 321-pin

Zero Insertion Force (ZIF) CPU socket for PentiumTM

processors running at 75MHz, 90MHz, 100MHz, 120MHz,

133MHz or 150MHz frequencies. This ZIF socket allows

users to easily upgrade CPUs.

The difference between the G586SP and G586SP AIO is that

the G586SP AIO comes with a built-in video accelerator for

ultimate graphic displays. The VGA controller can display

graphic resolutions up to 1024 x 768, 256 colors, 75Hz at

1MB DRAM, and up to 1280x1024, 256 colors, 60Hz at

2MB DRAM. The built-in VGA function also supports video

playback, VESA DDC1 and DDC2B.

Both the G586SP and G586SP AIO are equipped with three

dedicated PCI slots, two dedicated ISA slots, and one shared

PCI/ISA slot. The board has two bus master PCI IDE con-

nectors. Bus mastering reduces CPU utilization during disk

transfer resulting more efficient use of CPU resources. The

system board is also equipped with two NS16C550A-compat-

ible serial ports, one SPP/ECP/EPP parallel port, one analog

VGA port (G586SP AIO model only), a floppy disk drive

controller, and one PS/2 keyboard or AT keyboard connector.

The board can support 2MB to 256MB of EDO or fast page

mode DRAM (x32 or x36, 60 or 70ns) using 72-pin SIMMs

(Single In-line Memory Module).

G586SP/G586SPAIO

Features and Specifications

Processor

•Intel®PentiumTM Processor 75/90/100/120/133/150MHz

•Future PentiumTM OverDrive Processor

Chipset

•SiS chipset:

SiS5511: PCI/ISA system and cache memory controller

SiS5512: PCI local data buffer

SiS5513: PCI system I/O

SiS6205 PCI graphics and video accelerator (G586SP AIO)

•Winbond W83787F/83877F super I/O controller

System Design

•Unified Memory Architecture (G586SP AIO): 64-bit main

memory is shared between the CPU and the graphics

controller

•Four 72-pin SIMM sockets

•2MB to 256MB onboard memory

•Uses EDO or fast page mode x32 or x36 DRAM, 60 or

70ns

•Supports 256KB, 512KB, or 1MB L2 cache, direct-map

WB or WT

•Uses 32Kx8, 64Kx8, or 128Kx8 SRAM

•Onboard asynchronous SRAM cache

•Uses Intel®COAST-compatible (Rev. 1.2) 160-pin cache

module slot for optional pipelined burst or synchronous

cache

•Award BIOS, Windows 95 Plug and Play compatible

•Flash EPROM for easy BIOS upgrades

Energy Efficient Design

•System power management supported

•CPU stopped clock control

•Hardware supports SMI green mode

•Microsoft/Intel APM 1.1 compliant

G586SP/G586SPAIO

•Four power saving modes: Normal, Doze, Sleep, and

Suspend

High-Performance 64-Bit Graphics Accelerator (G586SP AIO)

•Accelerated 64-bit graphics controller

•Built-in video accelerator

•Supports VESA DDC1 and DDC2B

•Graphic resolutions (Non-interlaced mode):

1MB: 640x480, 16M colors, 60Hz

800x600, 64K colors, 60Hz

1024x768, 256 colors, up to 75Hz

2MB: 640x480, 16M colors, 75Hz

800x600, 16M colors, 75Hz

1024x768, 64K colors, 75Hz

1280x1024, 256 colors, 60Hz

Two Bus Master PCI IDE Connectors

•PIO Mode 3 & 4 Enhanced IDE (data transfer rate up to

16.6MB/sec.)

•DMA Mode 2 Bus Master IDE (data transfer rate up to

22.2MB/sec.)

•Bus mastering reduces CPU utilization during disk

transfer

•ATAPI IDE CD-ROM supported

I/O Interface

•Winbond super I/O controller

•Supports 360KB, 720KB, 1.2MB, and 1.44MB floppy

drives

•Two NS 16C550A-compatible enhanced serial ports

•One SPP/ECP/EPP parallel port

•One analog VGA port (G586SP AIO)

Mouse/Keyboard Connectors

•One mini-DIN-6 PS/2 or AT keyboard connector

•Option: DIP 6-pin PS/2 mouse connector

G586SP/G586SPAIO

Expansion Slots

•Three dedicated PCI slots

•Two dedicated 16-bit ISA slots

•One shared ISA/PCI slot

PCI Bus Master Drivers

•DOS 5.0 - 6.x

•Windows 95, Windows 3.x

•Windows NT

•OS/2 2.x

•Novell NetWare 3.1x, 4.x

•SCO 2.x, UNIX 3.x

CPU Socket

•321-pin ZIF socket (Intel Socket 7)

•Option: VRM header

PCB

•280mm (11.02") x 220mm (8.66")

Package Checklist

The G586SP/G586SP AIO package contains the following

items:

•G586SP/G586SP AIO system board

•G586SP/G586SP AIO user’s manual

•One 34-pin floppy disk drive cable

•One 40-pin hard disk drive cable

•One 25-pin printer port cable for chassis mounting

•One card-edge bracket with serial port cable

•One 16-pin cable for the VGA connector

•One set of IDE software drivers

•One set of VGA drivers (G586SP AIO only)

•Option: PS/2 mouse port cables

•Option: Cache module

If any of these items is missing or damaged, please contact

your dealer or sales representative for assistance.

G586SP/G586SPAIO

vInstallation Overview

This chapter summarizes the steps in installing the board

into your system unit. It also includes a description of the

area in which you must work and directions for memory

installation. Before installing the system board, obtain the

memory you plan to install. Please refer to the memory chart

on page 9 for the type of SIM modules needed.

Note:

Do not use 5V SRAM cache as they will not function prop-

erly on the system board.

Preparing the Area

Before unpacking the system board, make sure the location

you have selected is free of dust and static electricity.

Excessive exposure to dust, static electricity, direct sunlight,

excessive humidity, extreme cold, and water can damage the

operational capabilities of your system board. Avoid placing

the unit on surfaces such as carpeted floors. These areas also

attract static electricity which can damage some circuits on

your system board.

Make sure the power source has a properly grounded, three-

pronged socket. It is essential that the power connection be

properly grounded for correct functioning of your system

board. For further protection, we recommend that you use a

surge suppressor. This will protect the system board from

damage that may result from a power surge on the electrical

line.

Move items that generate magnetic fields away from your

system board since magnetic fields can also damage your

system board. Once you have selected the ideal location,

unpack the system board carefully.

Este manual sirve para los siguientes modelos

Tabla de contenidos

Manuales populares de Placa madre de otras marcas

ASROCK

ASROCK ROMED8-2T Manual de usuario

Asus

Asus P2L97A Manual de usuario

Winmate

Winmate IC70 Manual de usuario

Asus

Asus MES-B Manual de usuario

Grantech

Grantech SYS8F377VGGA-3OMN Manual de usuario

Telit Wireless Solutions

Telit Wireless Solutions SL869-3DR Manual de usuario

Gigabyte

Gigabyte GA-9IVDT Manual de usuario

Texas Instruments

Texas Instruments ADS8372EVM Manual de usuario

Commell

Commell MS-C73 Manual de usuario

IBT Technologies

IBT Technologies MB860 Manual de usuario

Nvidia

Nvidia TEGRA DG-04927-001_V01 Manual de usuario

Biostar

Biostar M7VIT Bravo Instrucciones de funcionamiento e instalación

Intel

Intel D33217CK Manual de usuario

Asus

Asus F1A55-M LX PLUS R2.0 Manual de usuario

EPC

EPC EPC9147C Manual de usuario

Asus

Asus EX-B760M-V5 D4 Manual de usuario

EPOX

EPOX MU-8KHA0010 Manual de usuario

Ski-Doo

Ski-Doo Bombardier MPEM 219 700 090 Manual de usuario