DFI G586IPBS Manual de usuario

G586IPBS

Rev. 0+

System Board

User’s Manual

-D29251020-

No part of this document may be copied, reproduced in any

form, or by any means or used to make any transformation/

adaptation without the prior written consent of DFI, Inc.

DFI, Inc. makes no warranties with respect to this documen-

tation and disclaims any implied warranties of merchant-

ability, quality, or fitness for any particular purpose. The

information in this document is subject to change without

notice. DFI, Inc. reserves the right to make revisions to this

publication and to make changes to any and/or all parts of

its content, at any time, without obligation to notify any

person or entity of such changes. Further, DFI, Inc. assumes

no responsibility for any errors that may appear in this

document.

DFI is a registered trademark, and G586IPBS is a trade-

mark of Diamond Flower, Inc. All other product names

mentioned are trademarks or registered trademarks of their

respective companies.

vFCC Statement on Class B

This equipment has been tested and found to comply with the

limits for a Class B digital device, pursuant to Part 15 of the

FCC rules. These limits are designed to provide reasonable

protection against harmful interference when the equipment

is operated in a residential installation. This equipment

generates, uses and can radiate radio frequency energy and,

if not installed and used in accordance with the instruction

manual, may cause harmful interference to radio communica-

tions. However, there is no guarantee that interference will

not occur in a particular installation. If this equipment does

cause harmful interference to radio or television reception,

which can be determined by turning the equipment off and

on, the user is encouraged to try to correct the interference

by one or more of the following measures:

•Reorient or relocate the receiving antenna.

•Increase the separation between the equipment and the

receiver.

•Connect the equipment into an outlet on a circuit

different from that to which the receiver is connected.

•Consult the dealer or an experienced radio TV technician

for help.

Notice:

1. The changes or modifications not expressly approved by

the party responsible for compliance could void the

user's authority to operate the equipment.

2. Shielded interface cables must be used in order to

comply with the emission limits.

v Table of Contents v

Introduction ..............................................................................

Features and Specifications .........................................

Package Checklist ........................................................

Installation Overview ...............................................................

Preparing the Area ..............................................................

Handling the System Board ................................................

Tips in Handling the System Board ..............................

Hardware Installation...........................................................

Memory Installation .......................................................

Installing the Modules ............................................

Board Configuration ......................................................

Jumper Settings for Display Type and

CMOS Clean ..........................................................

Jumper Settings for Super I/O Setting and

IRQ Select ..............................................................

Cache Configuration .....................................................

Installing the Cache Module ..................................

VRM Header .................................................................

VRM Header and 3.3V Pentium Processor ...........

VRM Header and Future Low-Voltage CPUs ........

CPU Installation ............................................................

Jumper Settings for CPU .......................................

Jumpers JP11 and JP50 ..............................................

Installing Upgrade CPUs ..............................................

G586IPBS

vIntroduction

The G586IPBS system board offers several advanced fea-

tures integrated into the system board. Its design is based on

the new Peripheral Component Interconnect (PCI) local bus

and Industry Standard Architecture (ISA) standards.

The G586IPBS provides a 321-pin Zero Insertion Force

(ZIF) CPU socket for PentiumTM processors running at

75MHz, 90MHz, 100MHz, 120MHz, 133MHz or 150MHz

frequency. This ZIF socket allows users to easily upgrade

their CPUs. It also provides a VRM (Voltage Regulation

Module) header allowing you to upgrade to future low-

voltage CPUs.

It is equipped with four PCI slots and three ISA slots.

The system board has two bus master PCI IDE connectors.

Bus mastering reduces CPU use during disk transfer. The

system board is also equipped with two NS16C550-compat-

ible serial ports, an SPP/EPP/ECP parallel port, a floppy disk

drive controller, one PS/2 mouse port and one PS/2 or AT

keyboard connector.

The G586IPBS can support 8MB to 128MB of memory

using 1Mx36, 2Mx36, 4Mx36 and 8Mx36 72-pin SIM

modules.

G586IPBS

Features and Specifications

Processor

•Intel PentiumTM 75/90/100/120/133/150MHz

•Future PentiumTM OverDrive Processor

System Design

•Intel Triton chipset

•Four 72-pin SIMM sockets

•8MB to 128MB onboard memory

•Uses EDO or fast page mode x32 DRAM, 60 or 70ns,

•256KB or 512KB L2 cache, direct-map WB or WT

•Uses 3.3V pipeline burst or asynchronous cache SRAM

on 160-pin cache module (optional)

•EDO DRAM and pipeline burst cache SRAM give

optimal performance

•Award BIOS, Windows 95 Plug and Play compliant

•Flash EPROM for easy BIOS upgrades

Energy Efficient Design

•System power management supported

•CPU stopped clock control

•Hardware supports SMI green mode

•Microsoft/Intel APM 1.1 compliant

•External power management switch supported

Two Bus Master PCI IDE Connectors

•PIO Mode 3 & 4 Enhanced IDE (data transfer rate up to

16.6MB/sec.)

•DMA Mode 2 Bus Master IDE (data transfer rate up to

22.2MB/sec.)

•Bus mastering reduces CPU utilization during disk

transfer

•ATAPI IDE CD-ROM supported

G586IPBS

Integrated I/O

•Super I/O controller:

-Winbond W83787F,

-Winbond W83877F,

-SMC FDC37C665GT or

-SMC FDC37C669GT

•Two NS 16C550-compatible high speed UARTs

•One SPP/EPP/ECP parallel port

•One 720KB/1.2MB/1.44MB floppy controller

(Winbond W83787F only) or

One 720KB/1.2MB/1.44MB/2.88MB floppy controller

(Winbond W83877F, SMC FDC37C665GT,

SMC FDC37C669GT)

•Plug and Play compliant (Winbond W83877F,

SMC FDC37C669GT)

Integrated Audio System

•Compatible with Sound Blaster™, Sound Blaster Pro™

and Windows Sound System™

•Plug and Play compliant

•Industry leading Delta-Sigma data converters

•Dual DMA support w/FIFOs, full duplex operation

•MPC 2 compatible mixer

•Joystick port and MPU-401 compatible MIDI interface

•External FM and Wavetable synthesis support

•Serial audio data port

•Uses Crystal CS4232 multimedia audio system

controller

Connectors

•Serial ports: 2 connectors

•Parallel port: 1 connector

•IDE: 2 shrouded headers

•Floppy: 1 connector

•PS/2 mouse connector

•PS/2 keyboard connector or AT keyboard connector

•Audio DIP header

•One wavetable connector on the TWT-100 audio

expansion board

G586IPBS

Expansion Slots

•Four PCI slots (all bus masters)

•Three ISA slots (one shared with PCI slot)

CPU Socket

•VRM (Voltage Regulation Module) header allows

upgrade to future low-voltage CPUs

•321-pin ZIF socket (Intel Socket 7)

PCB

•4 layers

•280mm (11.02") x 220mm (8.66")

Slot Limitations

Due to the size of the CPU with its accompanying

heatsink/fan component, the length of the add-on cards

in PCI Slot 2, 3 and 4 is limited to 205 mm (measured

from the bracket of the card).

The length of the add-on card in PCI Slot 1 is limited to

205 mm only if its components protrude more than

5 mm from the components and/or solder side of the

card.

G586IPBS

Package Checklist

The G586IPBS package contains the following items:

•The G586IPBS system board

•The G586IPBS user’s manual

•One set of IDE driver diskettes

•One 34-pin floppy disk drive cable

•Two 40-pin IDE hard disk cables

•One 25-pin printer port cable for chassis mounting

•One card-edge bracket with serial and mouse port cables

•One TWT-100 audio expansion board

•One wavetable daugher board (optional)

•Cache module (optional)

If any of these items is missing or damaged, please contact

your dealer or sales representative for assistance.

G586IPBS

vInstallation Overview

This chapter summarizes the steps in installing the

G586IPBS system board into your system unit. It also

includes a description of the area in which you must work

and directions for memory installation. Before installing the

system board, obtain the memory you plan to install. Please

refer to the memory chart, page 9, for the number and type

of SIM modules needed for the amount of memory you

require.

Preparing the Area

Before unpacking the system board, make sure the location

you have selected is relatively free of dust and static electric-

ity. Excessive exposure to dust, static electricity, direct

sunlight, excessive humidity, extreme cold, and water can

damage the operational capabilities of your system board.

Avoid placing the unit on surfaces such as carpeted floors.

These areas also attract static electricity which can damage

some circuits on your system board.

Make sure the power source has a properly grounded, three-

pronged socket. It is essential that the power connection be

properly grounded for correct functioning of your system

board. For further protection, we recommend that you use a

surge suppressor. This will protect the system board from

damage that may result from a power surge on the electrical

line.

Move items that generate magnetic fields away from your

system board, since magnetic fields can also

damage your system board. Once you have selected the ideal

location, unpack the G586IPBS system board carefully.

Tabla de contenidos

Manuales populares de Placa madre de otras marcas

ASROCK

ASROCK ROMED8-2T Manual de usuario

Asus

Asus P2L97A Manual de usuario

Winmate

Winmate IC70 Manual de usuario

Asus

Asus MES-B Manual de usuario

Grantech

Grantech SYS8F377VGGA-3OMN Manual de usuario

Telit Wireless Solutions

Telit Wireless Solutions SL869-3DR Manual de usuario

Gigabyte

Gigabyte GA-9IVDT Manual de usuario

Texas Instruments

Texas Instruments ADS8372EVM Manual de usuario

Commell

Commell MS-C73 Manual de usuario

IBT Technologies

IBT Technologies MB860 Manual de usuario

Nvidia

Nvidia TEGRA DG-04927-001_V01 Manual de usuario

Biostar

Biostar M7VIT Bravo Instrucciones de funcionamiento e instalación

Intel

Intel D33217CK Manual de usuario

Asus

Asus F1A55-M LX PLUS R2.0 Manual de usuario

EPC

EPC EPC9147C Manual de usuario

Asus

Asus EX-B760M-V5 D4 Manual de usuario

EPOX

EPOX MU-8KHA0010 Manual de usuario

Ski-Doo

Ski-Doo Bombardier MPEM 219 700 090 Manual de usuario