Danfoss TP6000M Manual de usuario

User Instructions

TP6000M & TP6000MA Electronic Programmable Room Thermostats

Product Features

• 2 or 4 programmed events each day, set by installer

• 5/2 day programming, provides dierent set of

programmes for weekend

• AM/PM or 24 hour clock display set by user

• Centigrade or Fahrenheit temperature display, set by user

•Mains powered

• Factory pre-set programmes which can be edited by user

• Built-in & remote sensor versions

LCD DISPLAY

Heating Temperature

Event Number

Thermometer Mode Indicator

Temperature Override - Up

Temperature Override - Down

Thermostat Calling for Heat

Main Display

Time or Temperature

Day of week (1 = Monday)

Keyboard

Locked

BUTTONSLCD DISPLAYS

A) Important note; Resetting the unit - To ensure correct operation press reset button

before commencing with programming.

Important note; If no buttons are pressed for two minutes the unit will automatically go

back to run mode. All changes made will be saved.

B) USER PREFERENCES

Before programming the thermostat it is recommended that the user preferences as regards

clock display and temperature scale are set. Details of the available user preferences are shown

below:

Clock display: press both - and  buttons and hold for 2 seconds to change display between

AM/PM & 24 hour. Repeat to return to original setting.

Temperature scale: to select between centigrade and farenheit temperature displays, follow

the steps below:

1. Press - and  buttons for 2 seconds to enter temperature display mode

2. Press - and + buttons for 2 seconds to change between centrigrade and farenheit display

3.Press - and  buttons for 2 seconds to change display back to time display mode prior to

programming.

Display actual room temperature: to permanently display actual room temperature press both

- and  and hold for 2 seconds. Repeat to return to time display.

C) SETTING THE TIME OF DAY AND DAY OF WEEK

1 Press PROG button to enter programming mode.

2. Press + or – buttons to adjust time of day, if in AM/PM mode remember to ensure that AM/PM

setting is correct.

3. Press PROG to move on to select current day of week.

4. Press + or - button repeatedly until correct day of week is displayed. Day 7 is Sunday.

5. Press PROG button to advance to“Programming event times and temperatures”.

D) PROGRAMMING EVENT TIMES AND TEMPERATURES

Reminder - The thermostat can be set by the installer to provide 2 or 4 programme events per

day. The thermostat provides 5-day / 2-day Programming with one set of programmes for days

1-5, (Monday to Friday), and another set of programmes for days 6-7, (Saturday and Sunday).

Reminder - If thermostat has been set by building owner or installer for 2 events per day, only

2 events can be programmed.

Reminder – The time setting of all events are made in increments of 10 minutes.

Setting the time and temperatures events for Days 1-5.

1. Press + or – buttons to adjust event time for event 1.

plus 

plus

plus 

PROG

then

plus 

then

plus 

RESET

BUTTONSLCD DISPLAYS

2. Press PROG to advance to temperature setting.

3. Press  or  buttons to adjust heating temperature

OPTIONAL: If heating is not required, “O”can be selected below 5°C.

Press PROG button to move onto event 2 programming and follow details below:

1. Press + or – buttons to adjust event time.

2. Press PROG to advance to temperature setting.

3. Press  or  buttons to adjust heating temperature

OPTIONAL: If heating is not required, “O”can be selected below 5°C.

Press PROG button to move onto next event 3 programming and follow details below:

1. Press + or – buttons to adjust event time.

2. Press PROG to advance to temperature setting.

3. Press  or  buttons to adjust heating temperature

OPTIONAL: If heating is not required, “O”can be selected below 5°C.

Press PROG button to move onto next event 4 programming and follow details below:

1. Press + or – buttons to adjust event time.

2. Press PROG to advance to temperature setting.

3. Press  or  buttons to adjust heating temperature

OPTIONAL: If heating is not required, “O”can be selected below 5°C.

Press PROG to advance to programming of days 6 & 7.

Setting the time and temperatures events for Days 6-7.

1. Press + or – buttons to adjust event time.



PROG



PROG



PROG



PROG



PROG

then

BUTTONSLCD DISPLAYS

2. Press PROG to advance to temperature setting.

3. Press  or  buttons to adjust heating temperature

OPTIONAL: If heating is not required, “O”can be selected below 5°C.

Press PROG button to move onto event 2 programming and follow details below.

1. Press + or – buttons to adjust event time.

2. Press PROG to advance to temperature setting.

3. Press  or  buttons to adjust heating temperature

OPTIONAL: If heating is not required, “O”can be selected below 5°C.

Press PROG button to move onto next event 3 programming and follow details below:

1. Press + or – buttons to adjust event time.

2. Press PROG to advance to temperature setting.

3. Press  or  buttons to adjust heating temperature

OPTIONAL: If heating is not required, “O”can be selected below 5°C.

Press PROG button to move onto next event 4 programming and repeat steps F1 – F3 above.

1. Press + or – buttons to adjust event time.

2. Press PROG to advance to temperature setting.

3. Press  or  buttons to adjust heating temperature

OPTIONAL: If heating is not required, “O”can be selected below 5°C.

PROG



then



PROG

then



PROG

then



PROG

then

BUTTONSLCD DISPLAYS

DAILY USE INSTRUCTIONS

E) TEMPORARY CHANGES TO PROGRAMMED TEMPERATURES

Press either  or  buttons to view programmed temperatues.

Note: If O is selected this option does not operate.

Then use  button to temporarily raise temperature, a  symbol will appear in the LCD dis-

play.

Or use  button to temporarily lower temperature, a  symbol will appear in the LCD display.

Reminder - Limited temperature adjustment:The amount of temperature adjustment may have

been limited by the building owner or the installer.

Reminder - Automatic cancellation of overrides: Any temporary override of temperature is

cancelled at the next event.

F) SELECTING WEEKEND INTO WEEKDAY OVERRIDE

Week-end into week day override

To temporarily copy weekend programmes into weekdays press both  and  buttons together

and hold down for 2 seconds.

To cancel the weekend into weekday override press both  and  buttons twice.

Advice:

During weekdays, this allows weekend programmes to be temporarily be copied into the current

day. The programme reverts to normal operation at the end of the day.

G) SELECTING THERMOSTAT MODE

Thermostat mode options

Programmes can be permanently overridden by selectingTHERMOSTAT mode, this feature is used

if xed temperatures are required for extended periods of operation.

1. To enter THERMOSTAT mode press both  and  buttons together and hold down for 2

seconds to enter WEEKDAY into WEEK END override.

2. Press both  and  buttons together for a second time and hold down for 2 seconds to enter

THERMOSTAT mode. The default setting is heat only.

3. Once in THERMOSTAT mode it is possible to select the required heating temperatures and the

thermostat operating mode, see below for setting details.

4. Use  or  buttons to select required heating temperature.

Advice: THERMOSTAT mode can be cancelled at any time by pressing both and buttons

together and holding down for 2 seconds. This will return the unit to normal running mode.







and



and



and

then



and

Danfoss can accept no responsibility for possible errors in catalogues, brochures and other printed material. Danfoss reserves the right to alter its products without notice. This also applies to

products already on order provided that such alterations can be made without subsequent changes being necessary in specications already agreed.

Part No. 33074v07 07/07

Danfoss Randall Ltd

Ampthill Road,

Bedford, MK42 9ER

Tel: 01234 364621 Fax: 01234 219705

Email: danfossrandall@danfoss.com

Website: www.danfoss-randall.co.uk

Event Setting Time/ temp Days 1-5 Days 6-7

Time: 6:30 7:30

Temp. Heat: 20.0°C 20.0°C

User Time:

Temp. Heat:

Factory Time: 8:30 9:30

Temp. Heat: 15.0°C 20.0°C

User Time:

Temp. Heat:

Factory Time: 16:30 16:30

Temp. Heat: 21.0°C 21.0°C

User Time:

Temp. Heat:

Factory Time: 22:30 22:30

Temp. Heat: 15.0°C 15.0°C

User Time:

Temp. Heat:

OTHER FEATURES AND FUNCTIONS

H) DISPLAYING ROOM TEMPERATURE

To enter thermometer mode to display current room temperature press both - and  buttons

and hold for 2 seconds. To return to time display repeat press and hold operation.

! Remember - the unit will revert to time display after Programming or Advanced Programming

Mode has been entered.

Reminder – Whilst in thermometer mode if the display ashes a row of bars the measured

temperature exceeds the display limit.

I) RESETTING THE THERMOSTAT MEMORY

Caution – Returns thermostat to factory settings: This should only be carried out should the

performance of the thermostat become erratic, this is only likely to happen as a result of severe

electro-magnetic interference such as a lightening storm.

To reset clock and re-start the thermostats micro-processor press the RESET button. After doing

this the thermostat must be re-programmed.

J) SETTING RECORD

BUTTONSLCD DISPLAYS

-

plus

RESET

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Termostato de Danfoss

Danfoss

Danfoss HC75-3 Manual de funcionamiento

Danfoss

Danfoss ECL Comfort 310, A376 Manual de usuario

Danfoss

Danfoss REPI Series Manual de usuario

Danfoss

Danfoss ORT-01 Manual de usuario

Danfoss

Danfoss ECL Comfort 210 Manual de usuario

Danfoss

Danfoss DEVIreg Opti Manual de usuario

Danfoss

Danfoss TP7000-RF Diagrama de cableado

Danfoss

Danfoss ECL Comfort 210 Manual de usuario

Danfoss

Danfoss MTD Instrucciones de montaje

Danfoss

Danfoss CET B-RF Instrucciones de funcionamiento

Danfoss

Danfoss C37 Manual de usuario

Danfoss

Danfoss HCS6101-3 Instrucciones de uso

Danfoss

Danfoss ECL Comfort 310, A302 Manual de usuario

Danfoss

Danfoss TP7000 Series Manual de usuario

Danfoss

Danfoss FH-CWT Manual de usuario

Danfoss

Danfoss TP75-RF Manual de usuario

Danfoss

Danfoss REP24CO1 Manual de usuario

Danfoss

Danfoss TP7001 series Manual de usuario

Danfoss

Danfoss ECA 30 Manual de usuario

Danfoss

Danfoss TP4000 Range Manual de usuario

Danfoss

Danfoss REP24CO3 Manual de usuario

Danfoss

Danfoss TP4 Instrucciones de montaje

Danfoss

Danfoss Link FT Manual de usuario

Danfoss

Danfoss RET2001 Manual de usuario

Manuales populares de Termostato de otras marcas

EWELLY

EWELLY EW-181 Manual de usuario

Prolon

Prolon T1100 Instrucciones de instalación

Computherm

Computherm Q20 Manual de usuario

Heatmiser

Heatmiser neoStat Manual de usuario

Aube Technologies

Aube Technologies TH111GFCI-NP 240 VCA Manual de usuario

Mars

Mars HEAT CONTROLLER IR Wireless Thermostat Manual de usuario

Saswell

Saswell SAS920XWHB-7-S-RF Guía

Aircalo

Aircalo TFP1-ET85P2 Manual de usuario

Honeywell

Honeywell CM721 Manual de usuario

Carrier

Carrier DEBONAIR 33CS Manual de usuario

Lennox

Lennox iHarmony Zone Thermostat Instrucciones de montaje

Gemtech

Gemtech GT7000 Manual de instrucciones

Rollei

Rollei Smartes 45000 Manual de usuario

Sinope

Sinope TH1300RF Manual de usuario

Honeywell

Honeywell RLV4305 Manual de usuario

Honeywell

Honeywell Prestige 2.0 THX9421 Manual de usuario

NuTone

NuTone NTBZ48 Instrucciones de funcionamiento originales

Stelpro

Stelpro MAESTRO ASMT402AD Manual de usuario