Danfoss TP4000 Range Manual de usuario

Fig.1

TP4000

User Instructions

Fig.2

Before programming the thermostat press and release the RESET button to restart

the unit. (Fig. 1)

Setting the Clock and Day

The time is set in the factory and therefore it will not normally be necessary to do this

on site.

Accepting the Factory Pre-settings

The TP4000 has pre-set times already programmed in, which often suit most people

(see table below).

To adjust the factory pre-settings & set your own time and temperature

programmes

a) Press PROG (Fig. 2) Until 1st pre-set time and temperature appears in display(Fig.

3).

b) Use + or – buttons (Fig. 4) to adjust the TIME (press and hold to change in 10 min

increments).

c) Use Λ or V buttons (Fig. 5) to adjust the TEMPERATURE.

d) Press PROG (Fig. 2) to move to next preset time & temp (Event 2) (Fig. 6).

e) Repeat steps b, c & d for programming Events 3, 4, 5 & 6.

Returning to RUN mode

Press PROG (Fig. 2) – the colon in the LCD display will start to ash (Fig. 7).

Temporary User Overrides

Fig.5

Fig.4

Fig.6

Fig.7

Event Time Temp. °C

1 06:30 20

2 08:30 15

3 11:30 20

4 13:30 15

5 16:30 21

6 22:30 15

RESET

Fig.3

Fig.9

Fig.10

Selection of time

or actual room

temperature in main

LCD display

Temporary

override of

programmed

temperature

press

together

Frost

Protection

Fig.8

The TP4000 has several useful overrides which can be selected without aecting the

thermostat programming.

• Selection of time or actual room temperature in main LCD display – press +

and – together to change between settings (Fig. 8).

• Temporary override of programmed temperature – press Λ or V until required

temperature is displayed (override will automatically cancel at beginning of next

programmed event) (Fig. 9).

• Frost Protection – a constant low temperature can be selected whilst away from

home - press Λ and V together (Fig.10). Then use Λ or V to select the required

temperature. To return to automatic programming press Λ and V together

again.

The TP4000 is both a programmer and a room thermostat. It allows you to programme

up to 6 times and temperatures at which your heating will come on and go o each

day.

Danfoss Ltd

Ampthill Road

Bedford, MK42 9ER

Tel: 0845 1217 400

Fax: 0845 1217 515

Email: [email protected]

Website: www.heating.danfoss.co.uk

Fig.11

• A low battery symbol will ash in the LCD display (Fig. 11)

• You have 15 days to replace the battery before the unit will switch o.

• Remove old batteries and insert new ones. All settings including time are

maintained.

• Press and release the RESET button to restart the unit. (Fig. 1)

NB. If the display ever goes blank during normal operation, the batteries will need

to be renewed with high quality alkaline cells.The reset button should be pressed

to restart the unit. All times, dates and events will be retained and need not be

re-programmed.

Battery Replacement

Otros manuales para TP4000 Range

Tabla de contenidos

Otros manuales de Termostato de Danfoss

Danfoss

Danfoss GreenCon RC-T2 Manual de usuario

Danfoss

Danfoss CF-RP 088U0211 Manual de usuario

Danfoss

Danfoss MTD Instrucciones de montaje

Danfoss

Danfoss Icon Wireless Dial Manual de usuario

Danfoss

Danfoss ECL Comfort 210 Manual de usuario

Danfoss

Danfoss CP10C Manual de usuario

Danfoss

Danfoss ECL Comfort 210 Manual de usuario

Danfoss

Danfoss RET2001RF Manual de usuario

Danfoss

Danfoss MBC 8000 Manual de usuario

Danfoss

Danfoss ECtemp 130 Manual de usuario

Danfoss

Danfoss SH-E01 Manual de usuario

Danfoss

Danfoss RT51 Manual de usuario

Danfoss

Danfoss TP5001 series Instrucciones de uso

Danfoss

Danfoss HP75-1 Manual de usuario

Danfoss

Danfoss RTD 3120 Manual de usuario

Danfoss

Danfoss TP4 Instrucciones de montaje

Danfoss

Danfoss ORT-01 Manual de usuario

Danfoss

Danfoss Devireg 535 Instrucciones de uso

Danfoss

Danfoss GET B-RF Guía

Danfoss

Danfoss TPOne-M Manual de usuario

Danfoss

Danfoss TP4 Instrucciones de funcionamiento

Danfoss

Danfoss Icon Master Manual de usuario

Danfoss

Danfoss ECL Comfort 310, A361 Manual de usuario

Danfoss

Danfoss ECL Comfort 310, A376 Manual de usuario

Manuales populares de Termostato de otras marcas

EWELLY

EWELLY EW-181 Manual de usuario

Prolon

Prolon T1100 Instrucciones de instalación

Computherm

Computherm Q20 Manual de usuario

Heatmiser

Heatmiser neoStat Manual de usuario

Aube Technologies

Aube Technologies TH111GFCI-NP 240 VCA Manual de usuario

Mars

Mars HEAT CONTROLLER IR Wireless Thermostat Manual de usuario

Saswell

Saswell SAS920XWHB-7-S-RF Guía

Aircalo

Aircalo TFP1-ET85P2 Manual de usuario

Honeywell

Honeywell CM721 Manual de usuario

Carrier

Carrier DEBONAIR 33CS Manual de usuario

Lennox

Lennox iHarmony Zone Thermostat Instrucciones de montaje

Gemtech

Gemtech GT7000 Manual de instrucciones

Rollei

Rollei Smartes 45000 Manual de usuario

Sinope

Sinope TH1300RF Manual de usuario

Honeywell

Honeywell RLV4305 Manual de usuario

Honeywell

Honeywell Prestige 2.0 THX9421 Manual de usuario

NuTone

NuTone NTBZ48 Instrucciones de funcionamiento originales

Stelpro

Stelpro MAESTRO ASMT402AD Manual de usuario