Danfoss RET2000B-RF Manual de usuario

RET2000B-RF + RX1-S

Electronic digital RF thermostat with LCD

Installation Guide

Danfoss Heating

RET2000

For a large print version of these instructions

please call Marketing on 0845 121 7400.

Danfoss can accept no responsibility for possible errors in catalogues, brochures, and other

printed material. All trademarks in this material are property of the respective companies.

Hearby, Danfoss A/S declares that the radio equipment type RET2000B-RF + RX1-S is in

compliance with directive 2014/53/EU.

The full text of the EU declaration of conformity is available at the following internet

address, http://heating.danfoss.co.uk/xdoccat/14_CATC-J_MNU17497125_SIT313.html

ERP Class

The products represented within this document are classied according to, and allow

completion of, the Energy Related Product (ErP) Directive System Package che and the

ErP system data label. ErP Labelling obligation is applicable from 26th September 2015.

ERP

Class Product Function and ErP Description Additional ef-

ciency gain

IV TPI Room Thermostat, for use with on/o output heaters

An electronic room thermostat that controls both ther-

mostat cycle rate and in-cycle on/o ratio of the heater

proportional to room temperature. TPI control strategy

reduces mean water temperature, improves room tem-

perature control accuracy and enhances system eciency.

ErP

Product

Class

Danfoss Heating 3

Product Specications

RET2000B-RF RX1-S

Operating Voltage 2.5 – 3 VDC

(2xAA alkaline batteries) 230Vac 50/60Hz

Output Relay - 1 x SPDT Type 1B

Switch rating - 3A (1) at 230Vac

Output - Volt free

Setting temp. range 5-30°C (cooling 16-36°C) -

Operating temp. range 0-45°C

Battery lifetime 2 years -

Max. range 30 metres

Operating frequency 433.92MHz <1mW ERP

IP Rating IP20 IP40

Control On-O / Chrono Proportional selectable

Operating modes Heating / Cooling selectable

Construction EN 60730-2-9 EN 60730-1

Control pollution situation Degree 2

Rated impulse voltage - 2.5kV

Ball pressure test 75°C

Dimensions H84 x W84 x D35 H84 x W84 x D28

Software classication A

Important note RF products: Ensure that there are no large metal objects, such as

boiler cases or other large appliances, in line of sight between the transmitter and

receiver as these will prevent communication between thermostat and receiver.

RET2000

Mounting

Fix at a height of 1.5m

approx from the oor,

away from draughts or

heat sources such as

radiators, open res or

direct sunlight.

Please Note: This product should only be installed by a qualied

electrician or competent heating installer and should be in accordance

with the current edition of the IET wiring regulations.

RET2000B-RF Thermostat

Danfoss Heating 5

Mounting and Wiring

ELECTRONICS

234

COM ON OFF

230Vac

RX1-S Receiver

RET2000

DIL switch settings

Slide the DIL switches

to the settings required.

ON/OFF - output switches ON when below set temperature and

OFF when above. (Reverse when in cool mode)

CHRONO -

energy saving feature which res the boiler at regular

intervals to maintain a set temperature, achieving a constant

ambient environment for the user.

use 6 or 12 Cycles for radiator systems

use 3 Cycles for underoor heating

Danfoss Heating 7

DIL Switch Settings

CHRONO

6 CYCLES

3 CYCLES

HEATING

°C

KEYS UNLOCKED

ON/OFF

3/12 CYCLES

12 CYCLES

COOLING

°F

KEYS LOCKED

NO COMP DELAY

COMP DELAY 4 MINS

N/A

HEATING

°C

KEYS UNLOCKED

COMP DELAY

COMP DELAY 2 MINS

N/A

COOLING

°F

KEYS LOCKED

Heating selection

Cooling selection

RET2000

GB If the thermostat RET2000B-RF and receiver RX1-S have been

supplied together in a combined pack, the units have been

paired in the factory and no commissioning is required. If the

thermostat and receiver have been supplied separately follow

the steps below to pair the devices.

Step 1 RX1-S - Ensure RX1-S is wired in accordance with

instructions on page 5.

Step 2 RET2000B-RF - Insert 2xAA alkaline batteries. If the

RET2000B-RF is not already paired to the RX1-S it will enter it’s

learning mode shown by the ashing aerial icon.

Step 3 RX1-S - Press and hold down both the PROG and CH

buttons. The PROG LED will light for 1 second when it has

paired with the RET2000B-RF. Release buttons

A steady aerial icon on RET2000B-RF conrms that the devices

are now paired and ready for control of your heating or cooling

systems.

Commissioning

Danfoss Heating 9

The RET2000B-RF Advanced Programming Mode can be

accessed as follows:

• Press the V button when in heat mode or Λ button when in

cool mode until the standby mode is reached.

• The Λ button or V button should then be released and

then pressed and held for a further 5 seconds to enter the

Advanced Programming Mode.

• To indicate that the unit is in Advanced Programming Mode

the Standby Indicator will ash and the display will show the

setting number alternating with the current value for that

setting.

• To change the setting press either the Λ or V button.

Advanced Programming

RET2000

GB • A simultaneous push and release of both buttons will scroll

through the steps S1 to S6 and will save the current set value

if altered.

• To exit Advanced Programming Mode and return to Standby

Mode press and hold both buttons for more than 5 seconds.

• While in Advanced Programming Mode if no buttons are

pressed for more than 2 minutes the unit will automatically

return to Standby mode, and the value on the current setting

will not be saved.

S1 – Lower Temperature Limit

This setting allows for a Lower Temperature Limit to be set.

The Lower Limit can be set between 5°C (41°F) and 30°C

(86°F) in Heat mode, or between 16°C (61°F) and 36°C (97°F)

in Cool mode.

Default – 5°C/41°F for Heat mode or 16°C/61°F for Cool mode.

Este manual sirve para los siguientes modelos

Tabla de contenidos

Idiomas:

Otros manuales de Termostato de Danfoss

Danfoss

Danfoss ECtemp 550 Manual de usuario

Danfoss

Danfoss SET 3E Manual de usuario

Danfoss

Danfoss TP5000 RF Si Manual de usuario

Danfoss

Danfoss 088L5130 Manual de usuario

Danfoss

Danfoss REP24CO3 Manual de usuario

Danfoss

Danfoss BasicPlus2 WT-T Manual de usuario

Danfoss

Danfoss CF-RF Manual de usuario

Danfoss

Danfoss CET B-RF Instrucciones de funcionamiento

Danfoss

Danfoss ECtemp Touch Manual de usuario

Danfoss

Danfoss DEVIreg Room 140F1161 Manual de usuario

Danfoss

Danfoss RET MD Guía de solución de problemas

Danfoss

Danfoss RET B + RF Instrucciones de funcionamiento

Danfoss

Danfoss TP4 Instrucciones de montaje

Danfoss

Danfoss ECL Comfort 310, P318 Manual de usuario

Danfoss

Danfoss DEVIreg Smart Manual de usuario

Danfoss

Danfoss 102E7 Instrucciones de montaje

Danfoss

Danfoss ECL Comfort 310, A333 Manual de usuario

Danfoss

Danfoss TP4 Instrucciones de funcionamiento

Danfoss

Danfoss TP5000 si range Manual de usuario

Danfoss

Danfoss GreenCon RC-T2 Manual de usuario

Danfoss

Danfoss DEVIreg Opti Manual de usuario

Danfoss

Danfoss TRONE-RF Manual de usuario

Danfoss

Danfoss WP75-RF Manual de usuario

Danfoss

Danfoss ECtemp 532 Manual de usuario

Manuales populares de Termostato de otras marcas

EWELLY

EWELLY EW-181 Manual de usuario

Prolon

Prolon T1100 Instrucciones de instalación

Computherm

Computherm Q20 Manual de usuario

Heatmiser

Heatmiser neoStat Manual de usuario

Aube Technologies

Aube Technologies TH111GFCI-NP 240 VCA Manual de usuario

Mars

Mars HEAT CONTROLLER IR Wireless Thermostat Manual de usuario

Saswell

Saswell SAS920XWHB-7-S-RF Guía

Aircalo

Aircalo TFP1-ET85P2 Manual de usuario

Honeywell

Honeywell CM721 Manual de usuario

Carrier

Carrier DEBONAIR 33CS Manual de usuario

Lennox

Lennox iHarmony Zone Thermostat Instrucciones de montaje

Gemtech

Gemtech GT7000 Manual de instrucciones

Rollei

Rollei Smartes 45000 Manual de usuario

Sinope

Sinope TH1300RF Manual de usuario

Honeywell

Honeywell RLV4305 Manual de usuario

Honeywell

Honeywell Prestige 2.0 THX9421 Manual de usuario

NuTone

NuTone NTBZ48 Instrucciones de funcionamiento originales

Stelpro

Stelpro MAESTRO ASMT402AD Manual de usuario