Danfoss FH-CWP Manual de usuario
Instruction
FH-CWP Thermostat
2VI.CU.C2.02 Produced by Danfoss Floor Heating Hydronics 05.2011
Instruction FH-CWP Thermostat
1. Functional Overview . . . . . . . . . . . . . . . . . . . . . . . . . . 3
2. Mounting ..................................... 4
3. Installation.................................... 4
4. Manual Operating Mode (factory setting) . . . . . . 5
5. ON/OFF Timer Function. . . . . . . . . . . . . . . . . . . . . . . . 6
6. Advanced Programmable Timer Function . . . . . . 7
7. Choosing room temperature control or both
room and floor temperature control. . . . . . . . . . . . 10
8. Maximum floor temperature protection . . . . . . . . 11
9. Frost protection ............................... 12
10. Error messages................................ 12
11. Technical Specifications . . . . . . . . . . . . . . . . . . . . . . . 13
12. Figures and illustrations . . . . . . . . . . . . . . . . . . . . . . . 16
Index
IMPORTANT!
Protect the thermostat from dirt, fluids, concrete and do NOT in-
sert any objects into it. Do not cover the thermostat, for instance
by hanging towels directly in front of it.
Installation must be done by an authorized electrician.
3
Produced by Danfoss Floor Heating Hydronics 05.2011 VI.CU.C2.02
Instruction FH-CWP Thermostat
1. Functional Overview
Front - fig. 1
Push button
Push button M
Push button
Up/down selectors
Back - fig. 2
Screw hole for flush mounting
Terminals for cable mounting
Symbols in the display - fig. 3
Room Sensor
Floor Sensor
Actual temperature indication
Clock
Floor heating – Active
Set Room temperature
Set Floor temperature
ON/OFF Timer Function (Active or being
SET)
Indication that timer is ON or OFF
Advanced Programmable Timer Function
(Active or being SET)
Frost Protection – (Active or being SET)
Su. Actual weekday
4VI.CU.C2.02 Produced by Danfoss Floor Heating Hydronics 05.2011
Instruction FH-CWP Thermostat
2. Mounting
Placing the Room Thermostat - fig. 4
! Wherever possible, the room thermostat should be
installed where the effects of sunlight, draught, and
other heaters (eg. TV’s), etc. are avoided.
3. Installation
Installing the Room Thermostat- fig. 5 and fig. 6
• Remove the connection cable between front and
back part.
• Connect the thermostat correctly to mains supply
according to the Wiring Diagram - fig 6.
• Mount the thermostat by using the enclosed
screws to the wall box.
• Mount the front correctly.
Wiring Diagram – fig 6
The product must be connected to the following
leads:
• Term L: Phase (L) AC85-250V, 50/60 Hz
• Term NO: Valve (NO)
• Term NC: Valve (NC)
• Term N: Neutral (N)
• Term 2: Empty
• Terminal S2: Floor sensor
• Terminal S1: Floor sensor
5
Produced by Danfoss Floor Heating Hydronics 05.2011 VI.CU.C2.02
Instruction FH-CWP Thermostat
4. Manual Operating Mode
(factory setting)
Turn the thermostat ON or OFF by pressing Fig. 1.
Selecting Manual Mode
Turn ON the thermostat by pressing Fig. 1.
• Press M for 3 seconds - Fig.1.
• Select 01 = Manual Mode via Fig. 1.
Setting the Clock Fig. 3
Su. Mo. Tu. We. Th. Fr. Sa.
• Press Fig. 1 shortly, hour will flash.
• Use Fig. 1 to select the hour.
• Press Fig. 1 again, minutes will flash.
• Use Fig. 1 to select the minutes.
• Press Fig. 1 shortly, actual weekday will flash.
• Use Fig. 1 to select the day of the week.
Displaying the Room Temperature Fig. 3
• The actual room temperature is shown in the
display as default .
Setting and changing the desired Room
Temperature
• Press or Fig. 1 anytime to change the desired
room temperature value, is shown in the
display.
6VI.CU.C2.02 Produced by Danfoss Floor Heating Hydronics 05.2011
Instruction FH-CWP Thermostat
• When releasing the or Fig. 1 the display
returns to showing the actual room temperature
.
5. ON/OFF Timer Function
The ON/ OFF timer function allows you to program
the thermostat for one period with heating turned
OFF and one period with heating turned ON per day.
During the ON period the thermostat will regulate in
relation to the set temperature and TIMER ON will be
shown in the display. During the OFF period, the heat
is off, and TIMER OFF is shown in the display.
Turn ON the thermostat by pressing Fig. 1.
Selecting the Simple ON/OFF Timer Mode
• Press M Fig.1 for 3 seconds.
• Select 02 = Setting an ON/OFF timing, via Fig.
1 is shown in the display.
Setting the Clock Fig. 3
Su. Mo. Tu. We. Th. Fr. Sa.
• Press Fig. 1 shortly, hour will flash.
• Use Fig. 1 to select the hour.
• Press Fig. 1 again, minutes will flash.
• Use Fig. 1 to select the minutes.
• Press Fig. 1 shortly, actual weekday will flash.
• Use Fig. 1 to select the day of the week.
7
Produced by Danfoss Floor Heating Hydronics 05.2011 VI.CU.C2.02
Instruction FH-CWP Thermostat
Setting the timing ON/OFF
• Press Fig. 1, and TIMER ON and hour
flashes in the display.
• Use Fig. 1 to select the hour.
• Press Fig. 1 again, minutes will flash.
• Use Fig. 1 to select the minutes.
• Press Fig. 1, and TIMER OFF and hour
flashes in the display.
• Use Fig. 1 to select the hour.
• Press Fig. 1 again, minutes will flash.
• Use Fig. 1 to select the minutes.
Setting and changing the desired Room Tem-
perature
• Press or Fig. 1 anytime (whenever the
thermostat is ON) to change the desired room
temperature value, will be shown in the
display.
• When releasing the or Fig. 1 the display
returns to showing the actual room temperature
.
6. Advanced Programmable
Timer Function
The Advanced Programmable Timer Function allows
you to set a timer controlled program for automatic
comfort temperature and energy saving lower
8VI.CU.C2.02 Produced by Danfoss Floor Heating Hydronics 05.2011
Instruction FH-CWP Thermostat
setback temperature when standard room comfort
temperature is not required.
The function consist of two programs
Program 1: 4 events in 5 days (Mo. Tu. We. Th. Fr.)
Program 2: 4 events in 2 days (Sa. Su.)
• Turn ON the thermostat by pressing Fig. 1.
• Press M Fig. 1 for 3 seconds.
• Select 03 = Setting a 5+2 days - 4 event setback
program via Fig. 1 is shown in the
display.
Setting the Clock Fig. 3
Su. Mo. Tu. We. Th. Fr. Sa.
• Press Fig. 1 shortly, hour will flash.
• Use Fig. 1 to select the hour.
• Press Fig. 1 again, minutes will flash.
• Use Fig. 1 to select the minutes.
• Press Fig. 1 until week flashes.
• Use Fig. 1 to select the day of the week.
Program 1:
• Press Fig. 1 for 3 seconds, the number 1 and
Mo. Tu. We. Th. Fr. are displayed.
Program 1, Event 1:
• Use Fig. 1 to select the required start time.
9
Produced by Danfoss Floor Heating Hydronics 05.2011 VI.CU.C2.02
Instruction FH-CWP Thermostat
• Press Fig. 1 to accept this setting.
• Use Fig. 1 to select the required temperature.
• Press Fig. 1 to accept this setting.
Program 1, Event 2-4:
Repeat the Event 1 procedure for programming Event
2-4.
Program 2:
Sa. Su. are now shown in the display.
Program 2, Event 1:
• Use Fig. 1 to select the required start time.
• Press Fig. 1 to accept this setting.
• Use Fig. 1 to select the required temperature.
• Press Fig. 1 to accept this setting.
Program 2, Event 2-4:
Repeat the Event 1 procedure for programming Event
2-4.
The thermostat will continue the 4-event pro-
gramme based on the present time and day.
Temporarily Setting and Changing the Desired
Room Temperature
• Press or Fig. 1 anytime to change the
desired room temperature value, is shown
10 VI.CU.C2.02 Produced by Danfoss Floor Heating Hydronics 05.2011
Instruction FH-CWP Thermostat
in the display.
• When releasing the or Fig. 1 the display
returns to showing the actual room temperature
.
This temperature change is only temporary and
will be maintained only until the next programmed
setting!
7. Choosing room temperature
control or both room and floor
temperature control
Turn OFF the thermostat by pressing Fig. 1.
• Press Fig. 1 and Fig. 1 for 10 seconds. The
display will show 01.
• Press Fig. 1 to adjust desired controltype.
01=room temperature control, only with room
sensor, no floor sensor, check and setting only room
temperature.
02=both room and floor temperature control, with
room sensor and floor sensor, check and setting room
temperature and maximum floor temperature limit.
Factory setting is 01.
Otros manuales para FH-CWP
1
Tabla de contenidos
Otros manuales de Termostato de Danfoss
Danfoss
Danfoss Icon Master Manual de usuario
Danfoss
Danfoss TP7001 series Manual de usuario
Danfoss
Danfoss RT 14L Manual de usuario
Danfoss
Danfoss TP5000 si range Manual de usuario
Danfoss
Danfoss ECtemp 330 Manual de usuario
Danfoss
Danfoss TP4 Instrucciones de funcionamiento
Danfoss
Danfoss ECL Comfort 310 Manual de usuario
Danfoss
Danfoss TP7000M Manual de usuario
Danfoss
Danfoss ECL Comfort 310, A376 Manual de usuario
Danfoss
Danfoss REPI Series Manual de usuario
Danfoss
Danfoss 103E5 Manual de usuario
Danfoss
Danfoss Basic Plus2 Manual de usuario
Danfoss
Danfoss CET B-RF Instrucciones de funcionamiento
Danfoss
Danfoss RT51 Manual de usuario
Danfoss
Danfoss RET M Instrucciones de funcionamiento
Danfoss
Danfoss ECL Comfort 110 Manual de usuario
Danfoss
Danfoss Icon Master Manual de usuario
Danfoss
Danfoss ECtemp 531 Manual de usuario
Danfoss
Danfoss RET 230 HCW-3 Manual de usuario
Danfoss
Danfoss ST-S2 Manual de usuario
Manuales populares de Termostato de otras marcas
EWELLY
EWELLY EW-181 Manual de usuario
Prolon
Prolon T1100 Instrucciones de instalación
Computherm
Computherm Q20 Manual de usuario
Heatmiser
Heatmiser neoStat Manual de usuario
Aube Technologies
Aube Technologies TH111GFCI-NP 240 VCA Manual de usuario
Mars
Mars HEAT CONTROLLER IR Wireless Thermostat Manual de usuario
