Danfoss 103E5 Manual de usuario
Installation and User Guide
Danfoss Heating
103E5
Electronic Timeswitch
for Controlling Hot Water and Heating
(Including Factory Replacement Units FRU)
2
INDEX
Index
Installation
Product specication 3
Installation 4-6
Wiring 6-9
Replacement 10-11
User
What is a timeswitch 12
Your timeswitch 13
Setting the clock 14
Factory preset programmes 15
Setting the programme - 24 hour 16
Setting the programme - 5/2 day 17
Running the programme 18
Temporary user overrides 19
Battery backup 20
Contact details 24
Danfoss can accept no responsibility for possible errors in catalogues, brochures, and other printed
material. All trademarks in this material are property of the respective companies. Danfoss and the
Danfoss logotype are trademarks of Danfoss A/S. All rights reserved.
®
Certification Mark
3
Please Note:
This product should only be installed by a qualied
electrician or competent heating installer, and should be
in accordance with the current edition of the IEEE wiring
regulations.
Specication
Power supply 230 Vac ± 15%, 50 Hz
Switching action 1 x SPST, Type 1B
Switch rating 264 Vac, 50/60Hz, 3(1)A
Timing Accuracy ±1 min./month
Power Reserve Minimum 14 days
Enclosure Rating IP30
Max. Ambient Temperature 45°C
Dimensions, mm (W, H, D) 102 x 136 x 47
Design standard EN 60730-2-7
Control Pollution Situation Degree 2
Rated Impulse Voltage 2.5kV
Ball Pressure Test 75°C
Product specication
Specication
Installation Instructions
4
Installation
NB. For FRU units - go straight to point 6.
1. Loosen the xing screw in the base of the unit to release the
Wiring Cover.
2. Holding the unit face downwards, press rmly in the
centre of the wallplate and slide it apart and lift it from the
module.
3. Fix the wallplate and terminal block to the wall, or plaster
box, as required. Ensure that the screw heads do not
protrude beyond the vertical centre rib of the wallplate,
or this will prevent the module correctly locating onto the
wallplate.
4. Surface cables can only enter from below the unit. Cut
an appropriate cable aperture in the wiring cover. If the
wallplate is mounted on a plaster box, cables can enter
from the rear below the terminal block.
Installation
Screw xing holes
(screwheads MUST
NOT protrude above
centre rib)
Vertical centre rib
Wallplate & Terminals
5
5. Electrical connections are simplied by using a Wiring
Centre. However, if this is not used, the wallplate terminal
identication is as shown.
If the system being controlled is 230 Vac then terminals
3 and L must be linked with insulated cable capable of
carrying full load current. Whilst the unit does not require
an earth connection, a terminal is provided on the wallplate
for earth continuity purposes.
6. Referring to the wiring diagrams on page 6-9, connect the
unit as shown.
7. Find out from the user whether the unit is required to
operate in 24-hour mode (factory preset) or weekday/
weekend mode (5/2 day). To convert to 5/2 day mode
remove the small two-way connector from the pins towards
the left of the recess on the rear of the module, then press
the SELECT/ADVANCE/+/- buttons all at the same time to
RESET the unit.
8. Ensure all dust and debris are cleared from the area. Plug
the module into the wallplate by locating it onto the
wallplate and, when ush with it, sliding it down, ensure
the hook at the top of the wallplate engages with the slot
at the back of the module.
9. Before setting the programme, check the unit and circuit.
Press the SELECT button until the bar in the display lines up
with the word ON. Adjust the remote thermostats to check
the system operates correctly.
Installation
LOAD Mains Supply
(via 3 amp. fuse)
ON SPARE COM N L
123 5 6
6
103, 103E5
Wiring
Wiring
10. Then press the SELECT button until the bar lines up with
the word OFF and check the system does not operate.
11. When the circuit check has been completed, replace the
wiring cover and tighten the xing screw. Cut any cable
aperture in the wiring cover which may be necessary to
accommodate surface mounted cables.
12. Finally set time of day and programmes required, noting
that the unit is supplied with a pre-set programme, as
stated on Page 14.
7
Wiring
Typical Gravity DHW with pumped heating
L N L N
COM CALL
N
ROOM
' S TAT
L
N
BOILER
TERMINALS
PUMP
TERMINALS
LINK
103E5
TERMINALS
MAINS
SUPPLY
FUSED
3 AMP
123 56
Typical control of Pump for Central Heating on a Solid
Fuel System
12356
L
N
MAINS
SUPPLY
FUSED
3 AMP
L N
COM CALL
ROOM
' S TAT
N
LINK
PUMP
TERMINALS
103E5
TERMINALS
8
Wiring
Typical Heating Only system, Boiler and Pump
control
Typical control of Low Voltage System requiring
voltage free contacts
COM CALL
N
ROOM
' S TAT
L N BOILER
TERMINALS L N PUMP
TERMINALS
L
N
103E5
TERMINALS
MAINS
SUPPLY
FUSED
3 AMP
123 56
LINK
12356
103E5
TERMINALS
L
N
LOAD
MAINS
SUPPLY
FUSED
3 AMP
LOW
VOLTAGE
SUPPLY
COM CALL
LOW
VOLTAGE
ROOM
' S TAT
9
Wiring
Typical control of Heating when provided by
Combination type Boiler
Typical Heating & Hot Water control system using 3 port
mid-position valve
123 56
COM CALL
N
ROOM
' S TAT
INPUT OUTPUT NL
L
N
103E5
TERMINALS
MAINS
SUPPLY
FUSED
3 AMP
COMBI BOILER
TERMINALS
103E5
TERMINALS
123 56
MID-POSITION VALVE L N
L
N
MAINS
SUPPLY
FUSED
3 AMP
BOILER &
PUMP
TERMINALS
RED OR
ORANGE
WHITE
OR
BROWN
BLUE GREY
ROOM
' S TAT CYL.
' S TAT
SAT
CALL
COM
N
LINK
10
DANFOSS RANDALL
103E5
LOAD MAINS SUPPLY
(via 3 amp fuse)
An additional terminal block is
required where these discon-
nected leads (or pairs of leads)
should be terminated
ON SPARE COM
1 2 3 5 (N) 6 (L) A B C D
RANDALL 103, 103E, 103E7 1 2 3 5 6
RANDALL 3020 4 2 - 1,7 6 3 5
RANDALL TSR2 4 5 - 3 1,2 6 7
GRASSLIN 45, 45A, 45E 4 - 3 2 1
HORSTMANN 424 EMERALD
& PEARL AUTO RANGE 4 2 3 N L,1 5
HORSTMANN 423 PEARL,
EMERALD & TOPAZ 413 NL256
SANGAMO S254 Form 2S408
Form 5, S251 Form 2 LOAD - - N L
SANGAMO S610 F2, S611 F2,
S612 F2, S408 F4, S408 F6,
S253 F2, S255 F2
LOAD - SWITCH
LIVE N
MO-
TOR
LIVE
SANGAMO S409 Form 8 2 1 6 3,N 5,L
SANGAMO/RANDALL SET 1 4 2 5 N L
SMITHS IND. MKI, MKII P3 P1 P2 N L
Replacement
Otros manuales para 103E5
2
Tabla de contenidos
Otros manuales de Termostato de Danfoss
Danfoss
Danfoss BasicPlus2 WT-DM Manual de usuario
Danfoss
Danfoss TP4 Instrucciones de montaje
Danfoss
Danfoss ECtemp 550 Manual de usuario
Danfoss
Danfoss 088L5130 Manual de usuario
Danfoss
Danfoss Living Eco Manual de usuario
Danfoss
Danfoss Devireg 535 Instrucciones de uso
Danfoss
Danfoss TP4000 Range Manual de usuario
Danfoss
Danfoss living connect Z Manual de usuario
Danfoss
Danfoss RET 230 HCW-3 Manual de usuario
Danfoss
Danfoss GreenCon RC-C2 Manual de usuario
Danfoss
Danfoss HC6110-3 Manual de usuario
Danfoss
Danfoss FP735Si Manual de usuario
Danfoss
Danfoss TP5001 series Instrucciones de uso
Danfoss
Danfoss ECL Comfort 310 Manual de usuario
Danfoss
Danfoss living connect Manual de usuario
Danfoss
Danfoss TP5001 series Manual de usuario
Danfoss
Danfoss DEVI DEVIreg Opti Manual de usuario
Danfoss
Danfoss ECtemp 610 Manual de usuario
Danfoss
Danfoss RET 230 Manual de usuario
Danfoss
Danfoss 3020P Instrucciones de montaje
Manuales populares de Termostato de otras marcas
EWELLY
EWELLY EW-181 Manual de usuario
Prolon
Prolon T1100 Instrucciones de instalación
Computherm
Computherm Q20 Manual de usuario
Heatmiser
Heatmiser neoStat Manual de usuario
Aube Technologies
Aube Technologies TH111GFCI-NP 240 VCA Manual de usuario
Mars
Mars HEAT CONTROLLER IR Wireless Thermostat Manual de usuario
