Danfoss 088U0215 Manual de usuario
088U0215
GB Instruction CF-RF Room Thermostat with Infrared Floor Sensor
Danfoss Heating Solutions VIUHR402 © Danfoss 05/2011
2
Instruction CF-RF Room Thermostat with Infrared Floor Sensor
3
© Danfoss 05/2011 VIUHR402 Danfoss Heating Solutions
Index
1. Functional Overview ...............................4
2. Installation.........................................5
3. Temperature Settings...............................6
4. Transmission Test...................................9
5. Mounting.........................................10
6. Uninstallation.....................................10
7. Specifications .....................................11
8. Troubleshooting ..................................12
Figures and illustrations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Instruction CF-RF Room Thermostat with Infrared Floor Sensor
Danfoss Heating Solutions VIUHR402 © Danfoss 05/2011
4
1. Functional Overview
Front (fig. 1)
Up/down selector
Push button
Red LED (behind the cover)
InfraRed floor sensor
LED modes
Permanent light . . . . . . ON
No light .............. OFF
Slow flashing . . . . . . . . . Flashes
Fast flashing. . . . . . . . . . Flickers
Back (fig. 2)
Back plate
Back plate lock/unlock (turn 90°)
Screw hole for wall mounting
Battery placement
Screw and wall plug
Note: To activate batteries please remove enclosed strips
from batteries.
Instruction CF-RF Room Thermostat with Infrared Floor Sensor
5
© Danfoss 05/2011 VIUHR402 Danfoss Heating Solutions
2. Installation
Note: Assignment of Room Thermostats to Master Controller
should be within a distance of 1.5 m.
Activate Install mode on Master Controller (fig. 1)
• Use the menu selection button to select the Install
mode. Install LED flashes.
• Activate Install mode by pressing OK. Install LED
goes ON.
Activate Install mode on room thermostat
• Press the push button . LED and flicker during
communication.
Select output on Master Controller
• All available output LEDs on Master Controller light
up, and the first one flashes.
• Press output selection button to select desired
output (flashes). Accept with OK .
• All output LEDs go OFF. Selected output stays ON
shortly.
Room thermostat installation status
• Satisfactory: LED goes OFF.
• Not satisfactory: LED flashes 5 times.
Note: A room thermostat can be assigned to several outputs
if needed by repeating the installation process.
Instruction CF-RF Room Thermostat with Infrared Floor Sensor
Danfoss Heating Solutions VIUHR402 © Danfoss 05/2011
6
3. Temperature Settings
Digital Display (fig. 1)
SET Set value adjustment
MIN Minimum temperature limitation
MAX Maximum temperature limitation
Transmission link icon
Low battery indicator
Alarm icon
Settings only available from CF-RC Remote controller:
Lock icon
Timer icon
Room temperature icon
Floor temperature icon
Changing default display temperature (fig. 1)
1. The actual room temperature is shown in the display
as default.
2. To change default display from actual room tempera-
ture to actual floor surface temperature, press and
hold the push button until SET MAX is shown in the
display.
3. Press the button shortly and repeatedly until or
is flashing in the display.
4. Press the up/down selector to select the new default
display temperature:
Room temperature Floor surface temperature.
Instruction CF-RF Room Thermostat with Infrared Floor Sensor
7
© Danfoss 05/2011 VIUHR402 Danfoss Heating Solutions
Setting of room temperature
1. Make sure actual room temperature is shown in the
display.
2. Press the up/down selector to set the desired room
temperature value. SET is shown in the display.
3. When releasing the up/down selector the display
returns to actual temperature.
Note: The thermostat regulates the floor heating system
according to room temperature set point, within the
maximum and minimum limitations defined for the
floor surface temperature.
Room temperature limitation
1. Make sure actual room temperature is shown in the
display.
2. Press the push button until SET MAX is shown in
the display.
3. Press the up/down selector to set the maximum
room temperature limitation.
4. Press the push button shortly, SET MIN is shown in
the display.
5. Press the up/down selector to set the minimum
room temperature limitation.
6. Press the push button shortly and the actual floor
surface temperature is shown in the display.
Instruction CF-RF Room Thermostat with Infrared Floor Sensor
Danfoss Heating Solutions VIUHR402 © Danfoss 05/2011
8
Floor surface temperature limitation
1. Ensure actual floor surface temperature is shown in
the display illustrated by .
2. Press and hold the push button until SET MAX is
also shown in the display.
3. Press the up/down selector to set the maximum
floor surface temperature limitation.
4. Press the push button shortly, SET MIN is also
shown in the display.
5. Press the up/down selector to set the minimum
floor surface temperature limitation.
IMPORTANT!
As heat emission from the floor may vary slightly depending on
floor covering - and thereby cause inaccurate temperature
measurement - it may be necessary to adjust the setting of
max. and min. floor surface temperatures accordingly.
It is important always to follow recommendations from the
floor manufacturer regarding max. floor surface tempera-
ture.
It is recommended always to include mixing shunt for floor
heating circuits in order to ensure optimal flow tempera-
ture. - In addition to minimised energy consumption, correct
setting of the flow temperature will eliminate the risk of
excessive heat transfer to the floor.
Instruction CF-RF Room Thermostat with Infrared Floor Sensor
9
© Danfoss 05/2011 VIUHR402 Danfoss Heating Solutions
4. Transmission Test
Initiate transmission test on room thermostat (fig. 1)
• Press the push button .
• LED goes ON.
Link test is satisfactory
• LED goes OFF.
Link test is unsatisfactory
• LED flashes 5 times.
No Link connection to room thermostat
• Try to relocate room thermostat in the room.
• Or install CF-RU Repeater Unit and locate between
Master Controller and room thermostat.
Note: When connected to a room thermostat, the Master
Controller output LED(s) flash(es) during Link test.
Instruction CF-RF Room Thermostat with Infrared Floor Sensor
Danfoss Heating Solutions VIUHR402 © Danfoss 05/2011
10
5. Mounting
Placing a room thermostat (fig. 3)
• A room thermostat should be placed in accordance
with fig. 3.
IMPORTANT!
Wherever possible, a room thermostat should be installed
at a place where the effect of sunlight, strong artificial
light (e.g. halogen spotlight), draught, other heat-emitting
equipment (e.g. TVs) etc. is avoided.
Please note that no furniture, rugs etc. should be perma-
nently placed within the area of the InfraRed Floor Sensor as
shown in fig. 3.
6. Uninstallation
Activate Uninstall mode on Master Controller (fig. 1)
• Use the Menu selection button to choose the Unin-
stall menu. Uninstall LED flashes.
• Activate Uninstall mode by pressing OK . Uninstall
LED goes ON.
Deselect output on Master Controller
• Select output to be removed by output selection
button .
• Remove flashing output with OK .
Instruction CF-RF Room Thermostat with Infrared Floor Sensor
Tabla de contenidos
Otros manuales de Termostato de Danfoss
Danfoss
Danfoss RET 230 HC-1 Manual de usuario
Danfoss
Danfoss TP7000M Manual de usuario
Danfoss
Danfoss LinkFT Manual de usuario
Danfoss
Danfoss TP4 Instrucciones de funcionamiento
Danfoss
Danfoss 060L2150 Manual de usuario
Danfoss
Danfoss ECL Comfort 210 Manual de usuario
Danfoss
Danfoss ECtemp 330 Manual de usuario
Danfoss
Danfoss RET 230 Manual de usuario
Danfoss
Danfoss Icon Wireless Dial Manual de usuario
Danfoss
Danfoss TP75M Manual de usuario
Danfoss
Danfoss RT1 Instrucciones de montaje
Danfoss
Danfoss TP5E Manual de usuario
Danfoss
Danfoss ECL Comfort 310, P314 Manual de usuario
Danfoss
Danfoss TS715Si Manual de usuario
Danfoss
Danfoss MBC 8000 Manual de usuario
Danfoss
Danfoss DEVIreg 532 Manual de usuario
Danfoss
Danfoss RET2001 Manual de usuario
Danfoss
Danfoss TP75H Manual de funcionamiento
Danfoss
Danfoss TS715 Si Manual de usuario
Danfoss
Danfoss TP5001 series Manual de usuario
Manuales populares de Termostato de otras marcas
EWELLY
EWELLY EW-181 Manual de usuario
Prolon
Prolon T1100 Instrucciones de instalación
Computherm
Computherm Q20 Manual de usuario
Heatmiser
Heatmiser neoStat Manual de usuario
Aube Technologies
Aube Technologies TH111GFCI-NP 240 VCA Manual de usuario
Mars
Mars HEAT CONTROLLER IR Wireless Thermostat Manual de usuario
