D-Link DWL-P200 Manual de usuario
1
DWL-P200
Power Over Ethernet
Adapters
48V DC Power Adapter
©2004 D-Link Systems, Inc. All rights reserved. Trademarks or registered trademarks are the property of their respective holders. Software and
specifications subject to change without notice.
About Power Over Ethernet.
Check Your Package Contents
DWL-P200 Base Unit and Terminal Unit
Female-to-Female Power Connector
Ethernet (CAT5 UTP/Straight Through) Cable
Using a power supply
with a different voltage
rating will damage and void
the warranty of this product.
If any of the above items are missing, please contact your reseller.
The DWL-P200 Power Over Ethernet (POE) Adapters are designed to supply
operational power to a Network Device. These adapters eliminate the need to use an
additional AC/DC power supply at the Network Device giving you the ability to mount
an Network Device virtually anywhere in a building where power outlets are not
available, ( for example in, ceilings, attics). D-Link’s DWL-P200 Adapters take
advantage of the unused cable pairs within Ethernet Cat 5 cabling. The Base Unit
inserts DC voltage into the unused wires therefore allowing the single Category 5
cable to carry both Ethernet data and DC power to an Network Device. The POE
Terminal Unit splits the data and DC power apart, which is then supplied to the
Network Device.
Warning: Please follow the
instructions in this guide carefully.
Connecting these adapters
incorrectly may result in damage to
you network devices.
2
Connecting The DWL-P200
Base Unit
Terminal Unit
P+DATA OUT:
provides the data and
power to the terminal
unit. Connect this port
to the P+DATA IN on
the Terminal unit.
LAN IN: connect an RJ-45
straight-through cable to
your computer or switch.
Power In: using the
supplied 48V power
supply, connect to a
wall power outlet.
P+DATA IN: connect
a CAT 5 RJ-45
straight-through
cable from the P +
Data Out port on the
Base Unit.
LAN OUT: connect a
CAT 5 RJ-45 straight-
through cable to an
Ethernet enabled device.
Voltage
Selector: used
to select DC 5V/
2.5A or 12V/1A
DC Out: supplies 5V 2.5
or 12V 1 amps of power.
Using the included power
cable, connect to your
Ethernet enabled device’s
power.
3
Connecting The DWL-P200
Insert one end of a Cat 5 Ethernet RJ-45 cable into the “LAN IN” port
of the Base Unit. Connect the other end of the cable to your network
switch or PC.
DO NOT use two Base units together, or two Terminal units together.
In configuring your network, pair one Base unit with one Terminal unit.
Plug one end of the Power Adapter into the “DC 48V IN” Base Unit
and the other end into your electrical outlet. The green “PWR” LED
on the Base Unit should light up.
Do Not mistake the “LAN IN” port with the “P + DATA OUT” port.
Incorrectly plugging the wrong Ethernet cable into the wrong Ethernet
port may cause serious damage to your network devices. D-Link will not
replace or repair products or reimburse customers for devices that become
damaged due to incorrect installation, nor is liable for any loss of business
resulting in the incorrect installation of this product.
4
Connect another Cat 5 Ethernet cable from the Base Unit “P + DATA
OUT” to the “P+DATA IN” of the Terminal Unit.
Connecting The DWL-P200
Insert one end of the DC Power Cable that is provided into the
Terminal Unit, and the other end into the DC of the Network Device.
The Power LED of the Terminal Unit should light up.
Only use a CAT 5 Ethernet straight-through cable.
Use Voltage Selector to set DC output to 5V/2.5A or 12V/1A for the
Network Device.
5
Connecting The DWL-P200
At this point, your Network Device should have power and data, and
function normally.
Connect the provided Cat 5 Ethernet cable from the Terminal Unit
“LAN OUT” to the RJ-45 LAN port of the Network Device.
6
Category 5 Pin Usage
.Data: 1, 2, 3, 6
.Power: 4, 5, 7, 8
Voltage
.Input: 48VDC, 400mA
.Output: 5VDC, 2.5A or 12VDC, 1A
Ethernet
.Connector: RJ-45
.Data Rate: 10/100Mbps
.Cable: TIA/EIA - 568, Category 5
Dimensions
. Base Unit: 8.09 x 5.2 x 2.8cm
. Terminal Unit: 8.09 x 5.2 x 2.8cm
Weight
.Base + Terminal Unit: 4.1oz
Temperature
. Operating: 0°C to 40°C (32°F to 104°F)
. Storage: -40°C to 70°C (-40°F to 158°F)
Operating Humidity
.10% to 80%
Warranty
.1 Year
Specifications
Features
. Provides DC power over existing CAT 5 cabling to Access Points.
. Transforms incoming AC power into low-voltage DC power.
. Base and Terminal Power Over Ethernet modules powers any Network Device
requiring 5V or 12V DC input.
. Protects Access Points from possible damages due to power-surges.
. Output: 5VDC, 2.5A or 12VDC, 1A
LAN Computer
D-Link Wireless
Access Point
DWL-P200
Power Over Ethernet
(Base Unit)
DWL-P200
Power Over Ethernet
(Terminal Unit)
Ethernet Cable
DC Power Cable
AC/DC Power Adapter
Ethernet Cable
7
8
Technical Support
You can find software updates and user documentation on the D-Link website.
D-Link provides free technical support for customers within the United States and
within Canada for the duration of the warranty period on this product.
U.S. and Canadian customers can contact D-Link technical support through our
website, or by phone.
Tech Support for customers within the United States:
D-Link Technical Support over the Telephone:
(877) 453-5465
24 hours a day, seven days a week.
D-Link Technical Support over the Internet:
http://support.dlink.com
email:[email protected]
Tech Support for customers within Canada:
D-Link Technical Support over the Telephone:
(800) 361-5265
Monday to Friday 8:30am to 9:00pm EST
D-Link Technical Support over the Internet:
http://support.dlink.ca
email:[email protected]
Tech Support for customers within the Europe:
D-Link Europe (United Kingdom) Ltd:
4th Floor, Merit House, Edgware Road, Colindale, London
NW9 5AB United Kingdom
TEL: 44-020-8731-5555 SALES: 44-020-8731-5550
FAX: 44-020-8731-5511 SALES: 44-020-8731-5551
BBS: 44 (0) 181-235-5511
D-Link Technical Support over the Internet:
http://support.dlink.co.uk Email:[email protected]
Tabla de contenidos
Otros manuales de Cambiar de D-Link
D-Link
D-Link xStack DGS-3420 Series Manual de usuario
D-Link
D-Link DKVM-2K Manual de usuario
D-Link
D-Link DGS-3024 Manual de usuario
D-Link
D-Link DKVM-2K Manual de usuario
D-Link
D-Link DU-H7 Manual de usuario
D-Link
D-Link xStack DGS-3426 Manual de usuario
D-Link
D-Link DGS-3710 Series Manual
D-Link
D-Link DKVM-4U Manual de usuario
D-Link
D-Link DUB-H7 - Hub - USB Manual de usuario
D-Link
D-Link DES-6300 Manual de usuario
D-Link
D-Link DUB-M520 Manual de usuario
D-Link
D-Link DES-3224 - Switch Manual de usuario
D-Link
D-Link D DGS-3048 DGS-3048 Manual de usuario
D-Link
D-Link DUB-H7 Manual de usuario
D-Link
D-Link xStack DGS-3420-28SC Manual de usuario
D-Link
D-Link DFE-916x Manual de usuario
D-Link
D-Link DE-1824EI Manual de usuario
D-Link
D-Link xStack DGS-3450 Manual
D-Link
D-Link DFE-2600 Series Manual de usuario
D-Link
D-Link xStack DGS-3620-52P Manual de usuario
