D-Link DSL-524T Manual de usuario

Before You Begin

Make sure you have all the necessary information and equipment on hand before beginning

the installation.

Check Your Package Contents

DSL-524T

ADSLRouter

specifications subject to change without notice.

DSL-524T ADSL Router

CD-ROM (containing User Manual)

Ethernet (CAT5 UTP) Cable

Telephone Cable

Power Adapter

Using a power supply

with a different voltage

rating will damage and void

the warranty for this product.

If any of the above items is missing,

please contact your reseller.

This product can be se

up using any current we

rowser, i.e., Interne

Explorer 6, Netscape

avi

ator 6.2.3, Mozill

or Firefox.

Connecting the Router to Your Computer

A. First, connect the power adapter to the receptor at the back panel of the

DSL-524T and then plug the other end of the power adapter to a wall outlet or

power strip. The Power LED will turn ON to indicate proper operation.

B. Insert one end of the cable into any Ethernet port on the back panel of the

DSL-524T and the other end of the cable to an Ethernet Adapter or available Ethernet

port on your computer.

C. Insert one end of the Telephone cable into the ADSL port on the rear panel of the

Router and insert the other end into the wall socket. If you need to install a low pass

filter, follow the instructions of your ISP.

Connecting the DSL-524T to your network

Rear Panel Connections

All cable connections to the Router are made at the rear panel. Connect the power adapter

here to power on the Router. Use the Reset button to restore the settings to the factory default

values in the next chapter for instructions on using the reset button).

ADSL port -

connect to

ADSL line

Ethernet ports -

connect to

Ethernet cable

Factory reset

button

Power input –

connect to

power adapter

Connecting the Router to Your Computer

Front Panel Connections

The LED indicators on the front panel include the Power, Status, ADSL and Ethernet indicators. The

ADSL and Ethernet indicators monitor link status and activity (Link/Act).

Your setup should resemble the one shown below.

Power: a steady light

indicates the

DSL2-524T is ready.

ADSL Link/Act: A steady green

light indicates a valid ADSL

connection. A blinking LED will

signify an active WAN session

Ethernet Link/Act: A steady green light

indicates a valid Ethernet connection while

a blinking LED indicates an active Ethernet

sess

Status: A blinking green LED

indicates the device is in proper

working order. A system failure will

result in the LED lighting solid or

Configuring the Router

To use your Web browser to access the web pages used to setup the Router, your computer

must be configured to “Obtain an IP address automatically”, that is, you must change the

IP network settings of your computer so that it is a DHCP Client. If you are using Windows

XP and do not know how to change your network settings, skip ahead to Appendix A and

read the instructions provided. You may also read the User Manual for instructions on

changing IP settings for computers running Windows operating systems.

Open your Web browser and type

“http://192.168.1.1” into the URL address

box. Then press the Enter or Return key.

The Login page appears.

Type “admin” for the User

Name and “admin” in the

Password field.

Click OK

Configuring the Router (continued)

Once you have logged in, the Home directory tab is prominent with the Setup Wizard menu

displayed. Most users will be able to use the Setup Wizard to establish the ADSL connection

to your ISP. To begin using the Setup Wizard, click on the Run Wizard button in the middle of

the web page. A pop-up menu will appear. This pop-up menu is the Setup Wizard. The Setup

Wizard procedure consists of four general steps:

1. Set the system password

2. Set the time zone

3. Set the Internet connection

4. Restart the Router

When you setup the Internet connection, you will need to enter information provided by your

ISP. The type of information you need depends on the type of connection you are setting up.

Click on the Run Wizard button.

Configuring the Router (continued)

The first Setup Wizard menu lists a summary of the steps required to complete the setup.

Click the Next button to begin setup.

Click the Next button.

Configuring the Router (continued)

Now configure the Time Zone used for the Router’s system clock. Select the appropriate time

zone and Daylight Saving Time setting for your location.

Select the Time Zone you are located

in by using the pull-down menu.

Click the Next button.

Configuring the Router (continued)

Next you will Set the Internet Connection Type for the WAN interface. Your ISP has given

this information to you. If you do not know what type of connection to use, exit the Setup

Wizard and contact your ISP for the information. The Setup wizard menu that appears when

you click the Next button depends on what connection type you select.

Select the Connection Type

used for your ADSL service.

Click the Next button.

Configuring the Router (continued)

PPPoE/PPPoA Connections

If you selected the PPPoE/PPPoA connection type in the previous menu, you will see the

Setup Wizard menu pictured here. Type in the Username and Password used to identify and

verify your account to the ISP. The VPI number and VCI number should not be changed

unless you have been instructed to change them. Select the Connection Type used for

encapsulation specific to your service. Click Next when you are ready to continue to the Setup

Completed menu.

If you are not sure what Connection Type,VPI and VCI to use, please check with your ISP.

Type the

Username

and

Password

for your ISP

account.

If you have

been told to

change the

or VCI number,

Type the new

values.

Click the Next button. Skip ahead to

the Setup Completed menu below.

Use the pull-down menu to choose the

correct Connection Type. The user may

choose between PPPoA VC-Mux, PPPoE

LLC or PPPoA LLC, as instructed by your

ISP.

Configuring the Router (continued)

Dynamic IP Address Connections

For this connection type, the user may choose Bridged IP LLC or Bridged IP VC-Mux. Both

of these connections require the user to have additional software located on their computer to

negotiate the connection with the ISP. Both Bridged modes will automatically set the network

connections. If you selected the Dynamic IP Address connection type, select the Connection

Type used for encapsulation and if you have been instructed to change the VPI number and

VCI number, type in the new values. Click Next when you are ready to continue the Setup

Completed menu.

Select the

Encapsulation

as 1483

Bridged IP

LLC or 1483

Bridged IP

VcMux as

instructed by

your ISP.

If you have

been told by

your ISP,

change the

VPI or VCI

number,

Type the new

values.

Click the Next button to skip ahead

to the Setup Completed menu.

The Cloned MAC Address field is

used to copy the MAC Address of

your Ethernet Adapter to the router.

Simply enter the MAC Address into

the space provided and click the

Clone Mac Address button.

Otros manuales para DSL-524T

Tabla de contenidos

Otros manuales de Enrutador de red de D-Link

D-Link

D-Link DI-804V Manual de usuario

D-Link

D-Link DES-1016D - Switch Manual de usuario

D-Link

D-Link DSL-G804V Manual de usuario

D-Link

D-Link DSR-150 Manual de usuario

D-Link

D-Link DIR-300 - Wireless G Router Manual de usuario

D-Link

D-Link DIR-825+ Manual de usuario

D-Link

D-Link DSL-2500U Manual de usuario

D-Link

D-Link DIR-815 Manual de usuario

D-Link

D-Link DWR-921 Manual de usuario

D-Link

D-Link Ethernet Broadband Router DIR-100 Manual de usuario

D-Link

D-Link DGL-4300 - GamerLounge Wireless 108G Gaming... Manual de usuario

D-Link

D-Link AirPremier N DAP-2690 Manual de usuario

D-Link

D-Link DSL-2543B Manual de usuario

D-Link

D-Link DIR-815 Manual de usuario

D-Link

D-Link DSL-524B Manual de usuario

D-Link

D-Link DRO-250i Manual de usuario

D-Link

D-Link DIR-605L Manual

D-Link

D-Link DIR-850L Instrucciones de funcionamiento y seguridad

D-Link

D-Link mydlink DSP-W215 Manual de usuario

D-Link

D-Link M15 Manual de usuario

D-Link

D-Link Router Manual de usuario

D-Link

D-Link DES-3550 Manual de usuario

D-Link

D-Link DIR-803 Manual de usuario

D-Link

D-Link DSS-8+ Manual de usuario

Manuales populares de Enrutador de red de otras marcas

Allnet

Allnet ALL0333AU Manual de usuario

HomeSeer

HomeSeer HT-SEL Manual de usuario

Sercomm

Sercomm Genesis OC3505D Manual de usuario

Billion

Billion BIPAC 5102 Series Manual de usuario

TP-Link

TP-Link TD-8817 Manual de usuario

Motorola

Motorola MR1900 Manual de usuario

Digi

Digi IX14 Manual de usuario

Cisco

Cisco NCS 540 Manual

XAVi

XAVi X8821e Manual de usuario

BEC

BEC 6200WZL Manual de usuario

MikroTik

MikroTik hAP ac3 Series Manual de usuario

Korenix

Korenix JetNet 5428G Series Manual de usuario

NETGEAR

NETGEAR FS526T - Switch Manual de usuario

Korenix

Korenix JetNet 5710G Series Manual de usuario

Automated Logic

Automated Logic ZN551 Manual del propietario

Cisco

Cisco ASR 1000 Series Manual del operador

EnGenius

EnGenius ESR-9710 Manual de usuario

Cisco

Cisco 805 Series Instrucciones de funcionamiento y seguridad