D-Link DES-1016D - Switch Manual de usuario
D-Link DES-1016D
16-port 10/100 Ethernet Switch
Manual
Building Networks for People
RECYCLABLE
(May. 2005)
Ver. 1.02
P/N : 2907D1016D16004
i
TABLE OF CONTENTS
ABOUT THIS GUIDE ................................................................1
PURPOSE .................................................................................................................... 1
TERMS/USAGE........................................................................................................... 1
OVERVIEW OF THIS USER’S GUIDE ........................................................................... 1
INTRODUCTION .......................................................................2
FAST ETHERNET TECHNOLOGY ................................................................................ 2
SWITCHING TECHNOLOGY ........................................................................................ 3
FEATURES.................................................................................................................. 4
UNPACKING AND SETUP .......................................................5
UNPACKING ............................................................................................................... 5
SETUP ........................................................................................................................ 5
DESKTOP INSTALLATION........................................................................................... 6
RACK MOUNTING...................................................................................................... 6
IDENTIFYING EXTERNAL COMPONENTS........................8
TECHNICAL SPECIFICATION ............................................10
1
ABOUT THIS GUIDE
Congratulations on your purchase of the DES-1016D 16-port
10/100Mbps Auto-negotiation Fast Ethernet Switch. This device
integrates 100Mbps Fast Ethernet and 10Mbps Ethernet network
capabilities in a highly flexible package.
Purpose
This guide discusses how to install your DES-1016D.
Terms/Usage
In this guide, the term “Switch” (first letter upper case) refers to DES-1016D
16-port 10/100Mbps Fast Ethernet Switch, and “switch” (first letter lower
case) refers to other Ethernet switches.
Overview of this User’s Guide
Introduction. Describes the Switch and its features.
Unpacking and Installation.Helps you get started with the basic installation
of the Switch.
Identifying External Components. Describes the front panel, rear panel and
LED indicators of the Switch.
Technical Specifications. Lists the technical (general, physical and
environmental, and performance) specifications of the Switch.
2
INTRODUCTION
This chapter describes the features of the DES-1016D and some background
information about Ethernet/Fast Ethernet switching technology.
Fast Ethernet Technology
The growing importance of LANs and the increasing complexity of desktop
computing applications are fueling the need for high performance networks.
A number of high-speed LAN technologies have been proposed to provide
greater bandwidth and improve client/server response times. Among them,
100BASE-T (Fast Ethernet) provides a non-disruptive, smooth evolution
from the current 10BASE-T technology. The non-disruptive and smooth
evolution nature, and the dominating potential market base, virtually
guarantee cost-effective and high-performance Fast Ethernet solutions in the
years to come.
100Mbps Fast Ethernet is a new standard specified by the IEEE 802.3 LAN
committee. It is an extension of the 10Mbps Ethernet standard with the
ability to transmit and receive data at 100Mbps, while maintaining the
CSMA/CD Ethernet protocol. Since the 100Mbps Fast Ethernet is compatible
with all other 10Mbps Ethernet environments, it provides a straightforward
upgrade and takes advantage of the existing investment in hardware, software,
and personnel training.
3
Switching Technology
Another approach to pushing beyond the limits of Ethernet technology is the
development of switching technology. A switch bridges Ethernet packets at
the MAC address level of the Ethernet protocol, transmitting among
connected Ethernet or Fast Ethernet LAN segments.
Switching is a cost-effective way of increasing the total network capacity
available to users on a local area network. A switch increases capacity and
decreases network loading by dividing a local area network into different
segments, which don’t compete with each other for network transmission
capacity.
The switch acts as a high-speed selective bridge between the individual
segments. The switch, without interfering with any other segments,
automatically forwards traffic that needs to go from one segment to another.
By doing this the total network capacity is multiplied, while still maintaining
the same network cabling and adapter cards.
For Fast Ethernet networks, a switch is an effective way of eliminating
problems of chaining hubs beyond the “two-repeater limit.” A switch can be
used to split parts of the network into different collision domains, making it
possible to expand your Fast Ethernet network beyond the 205-meter network
diameter limit for 100BASE-TX networks. Switches supporting both
traditional 10Mbps Ethernet and 100Mbps Fast Ethernet are also ideal for
bridging between the existing 10Mbps networks and the new 100Mbps
networks.
Switching LAN technology is a marked improvement over the previous
generation of network bridges, which were characterized by higher latencies.
Routers have also been used to segment local area networks, but the cost of a
router, the setup and maintenance required make routers relatively
impractical. Today switches are an ideal solution to most kinds of local area
4
network congestion problems.
Features
The DES-1016D is designed for easy installation and high performance in an
environment where traffic on the network and the number of users increase
continuously.
916-port 10/100BASE Ethernet Switch with RJ-45 connectors
9Supports Auto-negotiation of speed and duplex modes for each port
9Supports Auto-MDI/MDI-X for each port
9Wire speed reception and transmission
9Store-and-Forward switching method
9Integrated address Look-Up Engine, supports 8K absolute MAC
addresses
9Supports 160KbytesRAM fordatabuffering
9Front-panel diagnostic LEDs
9Broadcast storm protection
9IEEE 802.3x flow control for full-duplex
9Back pressure flow control for half-duplex
5
UNPACKING AND SETUP
This chapter provides unpacking and setup information for the DES-1016D.
Unpacking
Open the shipping carton for the Switch and carefully unpack its contents.
The carton should contain the following items:
9One DES-1016D 16-port 10/100Mbps Fast Ethernet Switch
9One AC power cord, suitable for your area’s electrical power
connections
9Four rubber feet to be used for shock cushioning
9Screws and two mounting brackets
9Quick Installation Guide
9This User’s Guide
If any item is found missing or damaged, please contact your local reseller
for replacement.
Setup
Please consider the following when setting up the Switch:
1. The surface must support at least 5 kg.
2. The power outlet should be within 1.42 meters (6 feet) of the device.
3. Visually inspect the power cord and see that it is secured fully to the AC
power connector.
6
4. Make sure that there is proper heat dissipation from and adequate
ventilation around the Switch. Do not place heavy objects on the Switch.
Desktop Installation
When installing the Switch on a desktop, the rubber feet included
with the device must be attached first. Attach these cushioning
feet on the bottom at each corner of the device. Allow enough
ventilation space between the device and the objects around it.
Fast Ethernet Switch installed on a Desktop or Shelf
Rack Mounting
The DES-1016D can be mounted in an EIA standard-size, 19-inch rack,
which can be placed in a wiring closet with other equipment. Attach the
mounting brackets at the switch’s front panel (one on each side), and secure
them with the provided screws.
7
Attaching the mounting brackets to the Switch
Then, use screws provided with the equipment rack to mount each switch in
the rack.
Installing the Switch in an equipment rack
8
IDENTIFYING EXTERNAL COMPONENTS
This section identifies all the major external components of the DES-1016D.
The figure below shows the front panels of the DES-1016D.
16-port 10/100Mbps Fast Ethernet Switch
1. LED Indicator Panel
Refer to the detailed information about each of the DES-1016D’s LED
indicators.
Power
This indicator lights green when the switch is receiving power; otherwise, it
is off.
Link / Act (Link/Activity)
This indicator lights on when the port is connected to a Fast Ethernet or
Ethernet device; if the light is blinking, it indicates that data is being
transmitted or received.
FDX / Col (Full-duplex/Collision)
This LED indicator lights green when a respective port is in full duplex (FDX)
Otros manuales para DES-1016D - Switch
5
Tabla de contenidos
Otros manuales de Enrutador de red de D-Link
D-Link
D-Link DSL-524B Manual de usuario
D-Link
D-Link DI-824VUP+ 2.4GHz Wireless VPN Router and Print... Manual de usuario
D-Link
D-Link DIS-100E Series Manual de usuario
D-Link
D-Link xStack DXS-3350SR Manual de instrucciones
D-Link
D-Link 504T Manual de usuario
D-Link
D-Link DIR-827 Manual de usuario
D-Link
D-Link Xtreme N DIR-614 Manual de usuario
D-Link
D-Link DIR-827 Manual de usuario
D-Link
D-Link DSL-526B Manual de usuario
D-Link
D-Link DSL-514 Manual de usuario
D-Link
D-Link DSL-510 Manual de usuario
D-Link
D-Link DES-5016 Manual de usuario
D-Link
D-Link DI-701 iShare Manual de usuario
D-Link
D-Link DSR-500 Manual de usuario
D-Link
D-Link DES-3010F Manual de usuario
D-Link
D-Link DES-3026 Manual de usuario
D-Link
D-Link DSL-124 Manual de usuario
D-Link
D-Link DIR-827 Manual de usuario
D-Link
D-Link xtreme n duo dap-1522 Manual de usuario
D-Link
D-Link TM DES-6500 Manual de usuario
Manuales populares de Enrutador de red de otras marcas
NETGEAR
NETGEAR FS526T - Switch Manual de usuario
Korenix
Korenix JetNet 5710G Series Manual de usuario
Automated Logic
Automated Logic ZN551 Manual del propietario
Cisco
Cisco ASR 1000 Series Manual del operador
EnGenius
EnGenius ESR-9710 Manual de usuario
Cisco
Cisco 805 Series Instrucciones de funcionamiento y seguridad