CYP PU-507RX-SCD Manual de usuario
PU-507RX-SCD
5-Play™ HDBaseT™ Receiver with integrated video scaling
& audio breakout (inc. PoE & single LAN, up to 100m) -
stereo audio only
OPERATION MANUAL
3
DISCLAIMERS
The information in this manual has been carefully checked and is
believed to be accurate. CYP (UK) Ltd assumes no responsibility for any
infringements of patents or other rights of third parties which may result
from its use.
CYP (UK) Ltd assumes no responsibility for any inaccuracies that may be
contained in this document. CYP (UK) Ltd also makes no commitment to
update or to keep current the information contained in this document.
CYP (UK) Ltd reserves the right to make improvements to this document
and/or product at any time and without notice.
COPYRIGHT NOTICE
No part of this document may be reproduced, transmitted, transcribed,
stored in a retrieval system, or any of its part translated into any language
or computer le, in any form or by any means—electronic, mechanical,
magnetic, optical, chemical, manual, or otherwise—without express
written permission and consent from CYP (UK) Ltd.
© Copyright 2011 by CYP (UK) Ltd.
All Rights Reserved.
Version 1.1 August 2011
TRADEMARK ACKNOWLEDGMENTS
All products or service names mentioned in this document may be
trademarks of the companies with which they are associated.
4
SAFETY PRECAUTIONS
Please read all instructions before attempting to unpack, install or operate
this equipment and before connecting the power supply.
Please keep the following in mind as you unpack and install this
equipment:
• Always follow basic safety precautions to reduce the risk of re,
electrical shock and injury to persons.
• To prevent re or shock hazard, do not expose the unit to rain,
moisture or install this product near water.
• Never spill liquid of any kind on or into this product.
• Never push an object of any kind into this product through any
openings or empty slots in the unit, as you may damage parts inside
the unit.
• Do not attach the power supply cabling to building surfaces.
• Use only the supplied power supply unit (PSU). Do not use the PSU if
it is damaged.
• Do not allow anything to rest on the power cabling or allow any
weight to be placed upon it or any person walk on it.
• To protect the unit from overheating, do not block any vents or
openings in the unit housing that provide ventilation and allow for
sucient space for air to circulate around the unit.
REVISION HISTORY
VERSION NO. DATE SUMMARY OF CHANGE
v1.00 06/11/2013 First release
v1.01 21/11/2013 Added RS-232 commands
5
CONTENTS
1. Introduction...........................................6
2. Applications ...........................................6
3. Package Contents ..................................6
4. System Requirements ...........................6
5. Features..................................................7
6. Operation Controls and Functions.......8
6.1 Front Panel................................................... 8
6.2 Rear Panel..................................................... 9
6.3 IR Cable Pin Assignment.......................10
6.4 RS-232 Pin Denitions ...........................10
6.5 RS-232 Commands .................................11
6.5 Remote Control........................................12
6.6 OSD Menu..................................................14
6.7 Output Resolution Support.................16
7. Connection Diagram .......................... 17
8. Specications...................................... 18
8.1 Technical Specications ........................18
8.2 CAT5e/6/7 Cable Specication ...........19
9. Acronyms............................................. 19
6
1. INTRODUCTION
The PU-507RX-SCD Receiver allows uncompressed HDMI signals and
IP data to be received over a Single CAT5e/6/7 cable. With full 5-Play
convergence, this solution features RS-232, 2-way IR control functionality,
and LAN serving over the same CAT5e/6/7 cable for transmission
distances up to 100m. This receiver also features an on-board scaler
with audio breakout enabling the installer to maximise video resolution
support to the display whilst de-embedding stereo audio via an optical
connection within the zone.
2. APPLICATIONS
Extend the operating distance of an HDMI signal
Up-scale standard denition video to High-Denition TVs/displays
Lecture room/Showroom/Meeting room/Classroom display and control
Up-scale HDMI output to HDTV/PC resolutions
3. PACKAGE CONTENTS
CAT5e/6/7 to HDMI with LAN/IR/RS-232/Bidirectional PoE Receiver
1×IR Receiver
1×IR Blaster
24V/2.7 A DC Power Adaptor
Remote control (CR-128)
Operation Manual
4. SYSTEM REQUIREMENTS
HDBaseT compatible Transmitter (input) and output to display with an
HDMI input connection.
7
5. FEATURES
Supports all v1.3 HDMI resolutions
Supports uncompressed video/audio up to 10.2Gbps
Video scaling ensuring maximum compatibility and optimum video
resolution support.
Supports Audio breakout via Optical output: Note: This device
supports stereo audio input/output only.
Common supported resolutions: HDTV: 480p, 576p, 720p, 1080i,
1080p, 1080p24; PC: VGA, SVGA, XGA, WXGA, SXGA, UXGA, WUXGA.
HDMI, HDCP, & DVI compliant
Supports HDCP repeating and CEC functions
Uncompressed data transfer over single CAT cable (100m - CAT6/7;
80m - CAT5e)
Uncompressed video 1080p, 60Hz, 48bits
5-Play™ convergence: HDMI, LAN, POE & Control (IR & RS232)
Supports 3D signals
Note:
1. This system was tested with CAT6/23AWG cables, results may vary with
cables of a dierent specication.
2. The PoE function is designed for powering compatible Transmitter units
only—non-PoE Transmitters will need their own power supply. Transmitters
from other brands may not be compatible.
3. DO NOT connect the LAN connection to the CAT5e/6/7 port. Doing so may
cause a power shutdown and may damage the device
8
6. OPERATION CONTROLS AND FUNCTIONS
6.1 Front Panel
XGA
MENU ENTER
-
+
720P
SERVICE HDMI OUT
OPTICAL OUT
2 3 4 5 6 71
1SERVICE: Reserved for manufacturer use only.
2IR Receiver window: Receives only the IR signal from the supplied
remote control.
3OPTICAL OUT: Connect to an amplier or active speakers with an
optical cable.
4HDMI OUT: Connect to an HDMI TV/Monitor
5MENU: Press this button to enter the On-Screen Display (OSD) menu.
6−/+: Use these buttons to navigate down and up in the on-screen
menu.
7ENTER: Press this button to conrm the selection.
Note:
Pressing '−' (MINUS) and ENTER simultaneously will immediately switch
the output resolution of the device to 720p60.
Pressing '+' (PLUS) and ENTER simultaneously will immediately switch the
output resolution of the device to XGA (1024×768).
9
6.2 Rear Panel
IR
Blaster
IR
Extender
CAT5e/6 IN
MODE
LINK
LANRS232 OUT
DC 24V
POWER
21 3 4 5 6 7
1Power LED: This LED will illuminate when the device is connected to
an active power supply.
2DC 24V: Connect the 24V DC power supply to the unit and plug the
adaptor into an AC outlet. Only one unit requires powering if both the
Transmitter and Receiver are both PoE compatible.
3RS-232 OUT: Connect to the device that is to be controlled (via D-Sub
9 pin female cable) by RS-232 commands.
4LAN: Connect to an active network for LAN serving. When any
compatible LAN equipped receivers are connected, this allows the
network access (including internet access if available) to be shared
between any connected LAN equipped receivers. Connect any Ethernet
equipped device e.g. a Smart TV or games console to the LAN port of a
receiver for that device to share the network/internet access.
Warning: DO NOT connect the LAN connection to the CAT5e/6/7 port.
Doing so may cause a power shutdown and may damage the device.
5IR Blaster: Connect the supplied IR Blaster cable for IR signal
transmission. Place the IR Blaster in direct line-of-sight of the
equipment to be controlled.
6IR Extender: Connect to the supplied IR Receiver cables for IR signal
reception. Ensure that remote being used is within the direct line-of-
sight of the IR Extender.
7CAT5e/6 IN: Connect to the Transmitter unit with a Single CAT5e/6
cable for receiving all data signals.
MODE LED: This LED will illuminate when the power is connected.
Link LED: This LED will illuminate when connected to a Transmitter
unit that is connected to a source that is outputting a signal.
10
6.3 IR Cable Pin Assignment
3
1
3
2
2
1Power
IR Blaster Signal
NC
IR Signal
Power
Ground
IR Extender
IR Blaster
6.4 RS-232 Pin Denitions
Pin Dene TX / RX
1N/C
2TxD/RxD
3RxD/TxD
4NC
5GND
6NC
7NC
8NC
9NC
Baud Rate: 9600bps
Data bit: 8 bits
Parity: None
Flow Control: None
Stop Bit: 1
Otros manuales para PU-507RX-SCD
1
Tabla de contenidos
Otros manuales de Receptor de CYP
CYP
CYP CH-2527TXV Manual de usuario
CYP
CYP PU-1106 Manual de usuario
CYP
CYP COH-Tx Manual de usuario
CYP
CYP DCT-30RX Manual de usuario
CYP
CYP 5Play PUV-1650TX Manual de usuario
CYP
CYP PU-607BDWP-RX Manual de usuario
CYP
CYP PRO-F21RX Manual de usuario
CYP
CYP PUV-1810RX-AVLC Manual de usuario
CYP
CYP CH-2535TX Manual de usuario
CYP
CYP PUV-3050RX-UA Manual de usuario
CYP
CYP CH-2540RX Manual de usuario
CYP
CYP CA-HDMI150R Manual de usuario
CYP
CYP PU-507RX-2H Manual de usuario
CYP
CYP CA-COMP100R Manual de usuario
CYP
CYP CH-103Rx Manual de usuario
CYP
CYP PU-DVI1109TX Manual de usuario
CYP
CYP HDMI Over CAT5 Manual de usuario
CYP
CYP CH-1507TX Manual de usuario
CYP
CYP CRS-232 Manual de usuario
CYP
CYP PU-515PL-WPRX Manual de usuario
