CYP QU-18WE Manual de usuario
OPERATION MANUAL
QU-18WE
v1.3 HDMI 1 to 8
Mountable Splitter
QU-18WE_Manual_EN.indd 1 06/05/2011 13:29:28
Table of Contents
1. Introduction 1
2. Features 1
3. Package Contents 1
4. Operation Controls and Functions 2
4.1 Front Panel Diagram 2-3
4.2 Bottom Panel Diagram 4
5. Connection Diagram 4
6. Specications 4-5
QU-18WE_Manual_EN.indd 2 06/05/2011 13:29:42
Page 1
1. Introduction
All the PUMA, HDMI over CAT5e/6 transmitters and receivers are the perfect
solution to extend HDMI signals via CAT cabling up to 40m. For even longer
distances, use the PU-108 repeater, these can also be cascaded. The PU-1106 also
allows you to use your existing Remote Control to control your device with the
included IR Receiver & Blaster.
2. Features
• v1.3 HDMI, HDCP 1.1 and DVI 1.0 compliant.
• HDMI 1 to 8 Mountable Splitter.
• Resolutions supported: PC - VGA to UXGA; HDTV - 480i to 1080p plus
1080p24fps.
• High Denition Audio supported: Dolby TrueHD, Dolby Digital Plus and DTS-
HD Master Audio plus LPCM.
• Auto signal amplication & equalisation improves signal transmission
distances.
• Supports CEC bypass.
• Supports ‘Deep Colour’ (10 & 12 bit).
• Selectable EDID settings - TV (downstream) and STD (xed).
• System reset function switch generate a command every 10 minutes to the
connected display which resets them to the correct HDMI input.
3. Package Contents
• 1 by 8 HDMI 1.3 Splitter
• Power adaptor
• Operational Manual
QU-18WE_Manual_EN.indd 1 06/05/2011 13:29:42
Page 2
4. Operation Controls and Functions
4.1 Front Panel
1
2
5
3
4
HDMI INPUT DC 5V
1
2
3
4
5
6
7
8
QU-18W
1X8 HDMI V1.3 Splitter
HDMI OUTPUT
EDID
Power
Sys.Reset
ON
OFF
8 Bit
12 Bit
2CH
Multi CH
STD
TV
ON
OFF
1. HDMI OUTPUT 1~8: Connect your LCD TV or HD monitor with EHDMI cables.
2. EDID selection: STD/TV – By switching to STD user can select both deep colour
and audio channels function, if switching to TV the unit will read TV’s EDID and
send the image from source accordingly.
Note:
1. When in STD mode the deep colour
is suggest switching to 8 bit for longer
distant display.
QU-18WE_Manual_EN.indd 2 06/05/2011 13:29:43
Page 3
1. 2CH/Multi CH – Support 2 channels or Multi audio channels audio function This
selection is only available when EDID is in STD mode.
Note:
When Multi CH is selected TV/
display must also support Multi CH function
otherwise, TV/display will have no audio output unless, HDMI output connect
to AVR and then to TV/display. 8/12 bit – Supports 8 or 12 bit’s deep colour
function. This selection is only available when EDID is in STD mode.
Note:
When both 8 bit and 12 bit displays are connected to the HDMI output
, switch
the unit to 8 bit using the selector switch to ensure all screens display a signal.
On the other hand, if all screens are 12 bit or all 8 bit then switch the selector
switch to 12 bit or 8 bit to ensure the correct output is displayed. The splitter
cannot output 8 bit and 12 bit simultaneously, so the lesser bitrate must be
selected to ensure the displays operate correctly.
2. Sys. Reset: System reset function. It is suggest having this function switch OFF
always except when doing system reset. By switching to ON the system will
reset HDMI output to HDMI 1 within 8~10 minutes, switching to OFF means CEC
bypass.
Note:
The system reset function only
functioning when the display has built-in CEC
functionality.
3. Power & LED: Power switch On/O Red LED illuminate when power is on.
4. HDMI INPUT: Connect your source equipment with HDMI cables. 3
QU-18WE_Manual_EN.indd 3 06/05/2011 13:29:43
Page 4
2
4.1 Bottom Panel
1. DC 5V: Plug the 5VDC power supply into the unit and connect the adaptor to AC
wall outlet. Red LED will illuminate when the Power is On.
6. Connection Diagram
7. Specications
Frequency Bandwidth 2.25Gbps (single link)
Input Port 1 x HDMI Female Ports
Output Port 8 x HDMI female Ports
HDMI Output Resolution 480i~1080p, 1080p24, VGA~UXGA
QU-18WE_Manual_EN.indd 4 06/05/2011 13:29:48
Page 5
Power Supply 5VDC/3.2A (US/EU standards, CE/FCC/UL certied)
Dimensions (mm) 94mm (W) x 220mm (D) x 32mm (H)
Weight (g) 460g
Chassis Material Aluminium
Silk Skin Colour Black
Operating Temperature Operating from 0°C ~ 40°C
QU-18WE_Manual_EN.indd 5 06/05/2011 13:29:48
Notes:
QU-18WE_Manual_EN.indd 6 06/05/2011 13:29:49
www.cypeurope.com
QU-18WE_Manual_EN.indd 7 06/05/2011 13:30:02
Tabla de contenidos
Otros manuales de Cables y conectores de CYP
CYP
CYP CPRO-2E Manual de usuario
CYP
CYP CDPS-4KQ Manual de usuario
CYP
CYP CPRO-2A Manual de usuario
CYP
CYP HDBT CHDBT-1H7CL Manual de usuario
CYP
CYP CLUX-18EU Manual de usuario
CYP
CYP CLUX-14EP Manual de usuario
CYP
CYP DT-12 Manual de usuario
CYP
CYP CSDI-14 Manual de usuario
CYP
CYP CLUX-18S Manual de usuario
CYP
CYP DT-12 Manual de usuario
CYP
CYP qu-2-4k22 Manual de usuario
CYP
CYP CPLUS-V8PT Manual de usuario
CYP
CYP CDVI-2DDS Manual de usuario
CYP
CYP CHDBT-1H4CPLV Manual de usuario
CYP
CYP CLUX-14E Manual de usuario
CYP
CYP CHDBX-1H1CPL Manual de usuario
CYP
CYP CHDBT-1H2CE Manual de usuario
CYP
CYP CLUX-18E Manual de usuario
CYP
CYP Clux-8 Manual de usuario
CYP
CYP CPLUS-V4E Manual de usuario
