CYP CDPS-4S2HSS Manual de usuario

CDPS-4S2HSS

4×2 SDI to HDMI Seamless Splitter with PIP

Operation Manual

DISCLAIMERS

The information in this manual has been carefully checked and

is believed to be accurate. Cypress Technology assumes no

responsibility for any infringements of patents or other rights of third

parties which may result from its use.

Cypress Technology assumes no responsibility for any inaccuracies

that may be contained in this document. Cypress also makes no

commitment to update or to keep current the information contained

in this document.

Cypress Technology reserves the right to make improvements to this

document and/or product at any time and without notice.

No part of this document may be reproduced, transmitted,

transcribed, stored in a retrieval system, or any of its part translated

into any language or computer le, in any form or by any means—

electronic, mechanical, magnetic, optical, chemical, manual, or

otherwise—without express written permission and consent from

Cypress Technology.

Version 1.1 August 2011

TRADEMARK ACKNOWLEDGMENTS

All products or service names mentioned in this document may be

trademarks of the companies with which they are associated.

SAFETY PRECAUTIONS

Please read all instructions before attempting to unpack, install or

operate this equipment and before connecting the power supply.

Please keep the following in mind as you unpack and install this

equipment:

• Always follow basic safety precautions to reduce the risk of re,

electrical shock and injury to persons.

• To prevent re or shock hazard, do not expose the unit to rain,

moisture or install this product near water.

• Never spill liquid of any kind on or into this product.

• Never push an object of any kind into this product through any

openings or empty slots in the unit, as you may damage parts

inside the unit.

• Do not attach the power supply cabling to building surfaces.

• Use only the supplied power supply unit (PSU). Do not use the PSU

if it is damaged.

• Do not allow anything to rest on the power cabling or allow any

weight to be placed upon it or any person walk on it.

• To protect the unit from overheating, do not block any vents or

openings in the unit housing that provide ventilation and allow for

sufcient space for air to circulate around the unit.

REVISION HISTORY

VERSION NO. DATE (DD/MM/YY) SUMMARY OF CHANGE

VR0 21/08/15 Preliminary release

CONTENTS

1. Introduction............................................ 1

2. Applications........................................... 1

3. Package Contents ................................ 1

4. System Requirements............................ 1

5. Features.................................................. 2

6. Operation Controls and Functions....... 3

6.1 Front Panel ........................................3

6.2 Rear Panel.........................................4

6.3 Remote Control................................5

6.4 OSD Menu.........................................6

6.5 RS-232 Protocol...............................16

6.6 RS-232 and Telnet Commands .....17

6.7 Software Application.....................24

6.8 Telnet Control .................................25

6.9 WebGUI Control .............................27

6.9.1 Image Adjust .........................27

6.9.2 Output Resolution .................27

6.9.3 Window Setup .......................28

6.9.4 OSD Settings ..........................29

6.9.5 Window Convert...................29

6.9.6 Chromakey Setup.................30

6.9.7 Ethernet..................................30

7. Connection Diagram .......................... 31

8. Specications ...................................... 32

9. Acronyms ............................................. 33

1. INTRODUCTION

The 4 by 2 SDI to HDMI Seamless Quad PIP Splitter is a high performance,

high speed zooming/shrinking system that can be easily congure

and control for quad or picture-in-picture video processing. Allowing

4 different SDI input sources to be freely selected and arranged on

to HDMI displays with total of 8 different types of settings. Supporting

resolution up to WUXGA@60RB, 1080p and audio up to 8CH with

sampling rate 48kHz for both inputs and outputs. Screen setting hot

keys, OSD, RS-232 and Telnet allows instant control and switching on

the output displays.

2. APPLICATIONS

• Broadcasting room and control

• Surveillance room and control

• Public advertisement and control

• SDI signal extending

3. PACKAGE CONTENTS

• 1×4 by 2 SDI to HDMI Seamless Splitter

• 1×Remote Control (CR-124)

• 1×12 V/3 A DC Power Adaptor

• 1× Rack Ear Sets

• Operation Manual

4. SYSTEM REQUIREMENTS

Input source equipment such as SNG camera or SDI signal, PC/Laptop

or RS-232 control devices and output HD TV/monitors with connection

cables.

5. FEATURES

• Supports SD-SDI (SMPTE 259M-C, at bitrates of 270 Mbit/s) input

signals up to 250M

• Supports HD-SDI (SMPTE 292M, at bitrates of 1.485Gbit/s and

1.485/1.001 Gbit/s) input signals up to 200M

• Supports 3G-SDI (SMPTE 424M/425M-AB, at bitrates of 2.970 Gbit/s

and 2.9701/1.001 Gbit/s) input signals up to 100M

• HDMI output compatible with DVI

• Combine four SDI inputs single into HDMI and output on to two

synchronize HD screen

• Seamless switching between channels and windows

• Zoom and Shrink 4CH input image and or to overlay them

• Supports PIP, POP and multi-windows display

• Supports OSD, RS-232 Remote and on-panel controls

• Fade-In-Out, Chromakey, Mirror and Rotation (90˚ left & right and

180˚ up & down) functions

• 8 Screen setting hot keys and extra 4 customized favorite screen

setting

• Easily to adjust size, position and setting of 4 input images via

WebGUI, only drag and few clicks can achieve output display

format setting

6. OPERATION CONTROLS AND FUNCTIONS

6.1 Front Panel

POWERPOWER

WINDOW

1FAV234

ABCDEFGH

CH 1CHANNEL IN CH 2CH 3CH 4FAV SELECT ENTER

AUDIO

INFO

720P/60Hz

WINDOW CDEFGH

1 2 3 5 6 9 10 487

4 5

1POWER Button & LED: Press this button to power on the device and

the LED will illuminate in green or set it to standby mode and the

LED will illuminate in Red.

2IR Window: Accept IR signal from the device’s remote control

included in the package only.

3CHANNEL IN 1~4: Press these buttons to rotate SDI 1~4 input source

on each channel to be display on screens. All channels can select

the same input or each channel a different input.

4WINDOW A~H & LEDs: Press these hot keys to select the screen

setting where A~D are display a full screen of each channel and

E~H are a different combination of a full screen setting with all 4

channels.

Windows A~D's channel input selection is corresponding to

channel input no. 1~4. That is, to change window A's input channel

must press channel input 1's button. Channel input 2~4's button

will not activate under window A's selection. Windows E~H's size

are adjustable through the OSD menu setting and only window

G & H is PIP(Picture in Picture) where E & F are POP (Picture out Of

picture) settings.

Under window E~H when the size setting is overlapping one

another, channel display sequence is CH4>CH3>CH2 >CH1. That is,

CH4 will cover CH3 and CH3 will cover CH2 and so on. Under some

display the borderline may have interference, adjusting display's

motion setting may resolve the interference issue.

5FAV SELECT & LEDs: Press this button to recall the favor setting from

1~4 and the LED will illuminate accordingly.

6MENU: Press this button to bring up the OSD menu on screen.

7ENTER: Press this button to enter into MENU selection and conrm

the selection.

8-/+ Buttons: Press these buttons to scroll down/up the OSD

selections.

9INFO: Press this button to bring up the information section from the

OSD menu.

10 AUDIO: Press this button to select audio channel.

Note:Press the 'INFO & AUDIO' buttons together to switch output

resolution to 720p@60Hz instantly.

6.2 Rear Panel

SDI IN

4321

BA SERVICE

HDMI OUT CONTROL RS232 DC 12V

1 2 3 4 5 6

1SDI IN: Connect with source equipment such as SNG camera or

SDI signal devices.

2HDMI OUT: Connect with HD TV/monitor for output image display.

3SERVICE: This slot is reserved for factory use only.

4CONTROL: Connect from PC/Laptop for Telnet control with RJ-45

cable.

5RS-232: Connect from PC/Laptop/RS-232 equipped device with

D-Sub 9pin cable for RS-232 command sending.

6DC 12V: Plug the 12V DC power supply into the unit and connect

the adaptor to an AC outlet.

6.3 Remote Control

1Power: Press this button to switch on

the device or press it again to set it to

standby mode.

2Info: Press this button to show system

information.

3Input CH 1~4: Press these buttons to

rotate SDI 1~4 input source on each

channel to be display on screen

4WA~WH: Press these hot keys to select

the screen setting where WA~WD are

display a full screen of each channel

and WE~WH are a different combination

of a full screen setting with all 4 channels.

5Mute: Press this button to mute the audio

from HDMI output port.

6 ▲/▼/►/◄ & OK Buttons: Press this

buttons to scroll through the OSD selection and press OK to enter

and conrm the setting.

7Menu: Press this button to enter into the OSD menu.

8Exit: Press this button to exit the OSD menu or the OSD settings.

9Fade-In-Out*: Press this button to switch on or off the Fade-in-out

function.

10 Chromakey*: Press this button to enter into Chroma function where

CH 1 is the background and CH 2 is the top image.

11 Mirror*: Press this button to display the screen in mirror image.

12 Rotation*: Press this button to rotate the image 90˚ left and right or

180˚ upside down.

13 Audio 1~4: Press these buttons to select audio from SDI input

source 1~4.

14 FAV. 1~4: Press these buttons to bring up the customized screen

settings.

Note:*Functions only work under Window A to D. The system will

force to switch to Window A when operate under Window E~H.

WA WE CH 1

WB WF CH 2

WC WG CH 3

WD WH CH 4

InputMute

MenuExit

Audio 1Fade In-Out FAV. 1

Audio 2 ChromakeyFAV. 2

Audio 3MirrorFAV. 3

Audio 4 RotationFAV. 4

Info Power

CR-124

6.4 OSD Menu

MAIN MENU 1ST LAYER 2ND LAYER 3RD LAYER

I/O Setup Output

Resolution

480p60

567p50

720p50

720p60

1080p24

1080p25

1080p30

1080p50

1080p60

1024x768

1280x800

1280x1024

1366x768

1440x900

1600x900

1600x1200

1920x1200

NATIVE1

Menu Back

OSD Setting Info Display On/Off

H Offset 0~20 (5)

V Offset 0~20 (5)

OSD Timeout 5~50/Off (10)

Transparent 0~10 (5)

Menu Back

Menu Exit

Tabla de contenidos

Otros manuales de Cables y conectores de CYP

Manuales populares de Cables y conectores de otras marcas

Philips

Philips SWA6310 Manual de usuario

StarTech.com

StarTech.com CRJ4550PK Manual de usuario

Nohau

Nohau EMUL-IP2K-PC Manual de usuario

Foxun

Foxun SX-SP144E-HD4K2K Manual de usuario

Philips

Philips SWA3305W Manual de usuario

opticis

opticis Stretch DVIM1-1P0x Manual de usuario

Volkswagen

Volkswagen VAS 6558A Manual de usuario

NEXIBO

NEXIBO N-13 Manual de usuario

Allen-Bradley

Allen-Bradley 1784-u2dhp Manual de usuario

Global Caché

Global Caché Flex Link Blaster Manual de usuario

Hauppauge

Hauppauge USB-Live2 Manual de usuario

Fenix

Fenix MPSV 15 Manual de usuario

BEGA

BEGA 71 085 Manual de usuario

Tesla

Tesla HPWC Manual de usuario

GAMERON

GAMERON LUXURY TV CABLE Manual de usuario

molex

molex Milli-Grid Dual row 87568 Series Manual de usuario

Burndy

Burndy Continental Industries thermOweld CRE-7 Manual de usuario

Chauvet DJ

Chauvet DJ Data Stream 8 Manual de usuario