Crux Logic ACPBM-77Y Manual de usuario

Smart-Play

Power/Video Harness

USB Extension Cable Microphone

ACPBM-77Y

Smart-Play Integration with Rear-View Camera Input for

E & F Series BMW Vehicles with CIC Infotainment Systems

INTERFACING SOLUTIONS

Crux Interfacing Solutions • 21541 Nordhoff Street, Unit C, Chatsworth, CA 91311

phone: (818) 609-9299 • fax: (818) 996-8188 • www.cruxinterfacing.com

rev.0724191 of 13

- Smart-Play Integraon system allows connecon of Android and other devices to the iDrive infotainment system.

- Control Apps using smartphone’s voice control feature or the factory iDrive Knob.

- Adds aermarket rear view camera input.

- Picture-in-picture mode combining aer-market rear-view picture with factory parking sensor graphics.

- Built-in on-screen display and setup.

- 1 trigger output (+12V max. 1A) for the camera power.

*NOTE: Android Phones must have a rmware version of 8 and above.

PRODUCT FEATURES:

PARTS INCLUDED:

ACPBM-77Y Module Power/CAN Harness 1 (E-Series) Power/CAN Harness 2 (F-series)

ACPBM-77Y Vehicle Harness 3.5mm to RCA Adapter Smart-Play Interface Module

NOTE:

This kit has two seperate POWER/CAN harnesses. Only use the harness that’s designed for your

vehicle.

POWER/CAN 1 - E-Series Trims

POWER/CAN 2 - F-Series Trims

LVDS 1 Cable (to vehicle) LVDS 2 Cable (to radio)

Setting the DIP switches of the Interface Box.

DIPs 1 and 2 on the back of the interface-box is used to set the monitor size. DIP 3 must be set to OFF.

After each change of the DIP switch settings you have to execute a power reset of the interface box!

Crux Interfacing Solutions • 21541 Nordhoff Street, Unit C, Chatsworth, CA 91311

phone: (818) 609-9299 • fax: (818) 996-8188 • www.cruxinterfacing.com

rev.072419

2 of 13

INSTALLATION DIAGRAM:

INTERFACING SOLUTIONS

ACPBM-77Y

DIP SWITCH SETTINGS:

+12V Switching

Output 1 (Pink Wire)

Rear-View

Camera

(Not Included)

Back of Headunit

CRUX LVDS 1

Cable

CRUX LVDS 2

Cable

*If using OEM Back-up

camera, leave REAR CAM

input unoccupied.*

Pink factory

LVDS Cable

*If installing after-market Back-Up

camera, use the pink wire to provide power to

to the camera, if not, please ignore this connection*

ACPBM-77Y

Vehicle Harness

UART

POWER/VIDEO

Smart-Play Module

Vehicle Auxiliary

Input (AUX input)

Female RCA to

3.5mm jack

Male L & R RCA

Outputs (Audio)

AUX

POWER / CAN

FRONT

CAM

REAR

CAM

UPDATE

Smartphone Cable

USB Input

12V Green Output 2

to ACC power

(on Smart-Play Harness)

Power/CAN

Harness

iDrive Knob

Retention Cable

ACPBM-77Y Module

ACC Power

Ground

Constant

LVDS

OUT

v. 123

Intelligent Solution

LVDS OUT

LVDS IN

Crux Interfacing Solutions • 21541 Nordhoff St., Unit C, Chatsworth, CA 91311

phone: (818) 609-9299 • fax: (818) 996-8188 • www.cruxinterfacing.com

rev.040119

2 of 12

INSTALLATION DIAGRAM:

INTERFACING SOLUTIONS

DIP SWITCH SETTINGS:

VEHICLE / SCREEN SIZE DIP 1 DIP 2 DIP 3

CIC-E (E-Series) / 6.5” OFF OFF

CIC-E (E-Series) / 8.8” OFF ON

CIC-F (F-Series) / 7” ON OFF

CIC-F (F- Series) / 10.2” ON ON

VRFBM-77EF

Front and Rear View Integration Interface

for Select BMW Vehicles with CIC Navigation Systems

BM-77EF Module

LVDS1 Cable

4-Pin HSD

Female LVDS

Vehicle Harness

BM-77EF

Harness

Power/CAN or

Power/CAN2

Harness

Back of Headunit

+12V Switching

Output 1 (Pink Wire)

Front

Camera

(Not Included)

Rear-View

Camera

(Not Included)

+12V Switching Output 2 (Green Wire)

Reverse Gear Signal Input

+12V (White Wire)

Female Quadlock

Vehicle Harness

DVD Player (Not Included)

Portable

Video

Player

(Not Included)

LVDS2 Cable

NOTES:

1. The Interface is installed behind the headunit and needs a constant +12V power source.

Smart-Play Integration with Rear-View Camera Input for

E & F Series BMW Vehicles with CIC Infotainment Systems

Refer to P. 7 for the CAN com-

municaon wiring for F-Series

vehicles, if needed.

Crux Interfacing Solutions • 21541 Nordhoff Street, Unit C, Chatsworth, CA 91311

phone: (818) 609-9299 • fax: (818) 996-8188 • www.cruxinterfacing.com

rev.072419

3 of 13

INTERFACING SOLUTIONS

ACPBM-77Y

INSTALLATION INSTRUCTIONS:

1. Installaon is done behind the front

panel.

2. Carefully remove the dashboard

front panel using a trim removal tool.

3. Carefully remove the hazard/door-

unlock panel and unplug the harness.

4. Remove the push-to-start panel and

its connector to fully take o the front

panel.

5. Remove the A/C control panel using

a trim removal tool, along with the

cables connected to it.

6. Carefully remove the Headunit

panel.

7. Remove the 4 screws bracing the

Headunit.

8. Remove the Headunit to gain access

to its backside.

9. Unplug the Quadlock connector

from behind the radio.

Smart-Play Integration with Rear-View Camera Input for

E & F Series BMW Vehicles with CIC Infotainment Systems

Crux Interfacing Solutions • 21541 Nordhoff Street, Unit C, Chatsworth, CA 91311

phone: (818) 609-9299 • fax: (818) 996-8188 • www.cruxinterfacing.com

rev.072419

4 of 13

INTERFACING SOLUTIONS

ACPBM-77Y

10. Unplug the 2-pin ber opc cable

from the factory Quadlock connector.

11. Plug in the 2-pin ber opc connec-

tor to the ACPBM-77Y harness (Female

side).

12. Tap the Black GND wire from the

Smart-Play Power/Video harness to the

black Ground wire on the ACPBM-77Y

vehicle harness (Male Side).

15. Tap the RED ACC wire from the

Smart-Play Power/Video harness to the

green +12V output on the ACPBM-77Y

harness.

13. Tap the Yellow constant wire from

the Smart-Play Power/Video harness to

the Red constant wire on the ACPBM-

77Y vehicle harness (Male Side).

14. Connect the male 8-pin connector

from the ACPBM-77Y to the female

8-pin connector on the Power/CAN

harness.

*Make sure you use the correct Power/CAN har-

ness for your vehicle trim (refer to NOTE on p.1)*

16. Plug the factory Quadlock connec-

tor in to the male side of the ACPBM-

77Y harness.

17. Plug in the female side of the

ACPBM-77Y harness to the Headunit.

18. Unplug the PINK LVDS factory cable

from the Headunit.

Smart-Play Integration with Rear-View Camera Input for

E & F Series BMW Vehicles with CIC Infotainment Systems

Crux Interfacing Solutions • 21541 Nordhoff Street, Unit C, Chatsworth, CA 91311

phone: (818) 609-9299 • fax: (818) 996-8188 • www.cruxinterfacing.com

rev.072419

5 of 13

INTERFACING SOLUTIONS

ACPBM-77Y

19. Connect the LVDS 2 cable in place

of the PINK LVDS factory cable.

20. Connect the factory PINK LVDS

cable to the male end of the LVDS 1

cable (CYAN colored connector).

21. Plug the otherside of the LVDS 1

cable into to the LVDS OUT port on

the ACPBM-77Y module. And plug the

otherside of the LVDS 2 cable into the

LVDS IN port on the same module.

22. If your vehicle is an F-series trim,

we will need to access the CAN data

from beneath the iDrive knob. This

only applys to you if you are using the

Power/CAN 2 Harness. If you are in-

stalling on an E-series trim (Power/CAN

1) you can skip steps 23 - 28.

Refer to P. 7 for the wiring diagram for

the F-series if needed.

23. Carefully remove the center trim

using a trim removal tool to get under-

neath the iDrive knob.

24. Your vehicle may have a 4-pin or

10-pin connector for the iDrive knob.

Remove the iDrive connector.

25. Using a pin removal tool, remove

the Green(CAN LO Pin 4) and Orange/

Green(CAN HI Pin 3) wires from the

iDrive connector.

Both 4 & 10 pin connectors have the same pin posions.

26. Insert the two pins (Orange/Green

--> Pin1 & Green --> Pin2) into the

empty 2-pin connector aatched to the

Yellow/Black & Blue/Black wires from

the Power/CAN 2 harness.

27. Insert the Yellow (CAN HI) --> Pin3

and Blue (CAN LO) ---> Pin4 wires into

the 4-pin iDrive connector (inplace

of the Green & Orange/Green wires

removed earlier).

Smart-Play Integration with Rear-View Camera Input for

E & F Series BMW Vehicles with CIC Infotainment Systems

28. Plug in the the modied iDrive con-

nector back into the port underneath

the iDrive knob.

29. Plug the Video Out from the Smart-

Play Power/Video harness into the

FRONT CAM input on the module.

30. Plug the otherside of the LVDS 1

cable into to the LVDS OUT port on

the ACPBM-77Y module. And plug the

otherside of the LVDS 2 cable into the

LVDS IN port on the same module.

31. If installing an aermarket back-up

camera, plug the camera’s video out

to the REAR CAM input on ACPBM-77Y

module. Use the PINK power output 1

wire provided on the Power/CAN har-

ness to power the camera. An image

is displayed in step 26. If retaining an

OEM camera or if you’re not installing

a back-up camera, skip steps 25 and 26.

32. Tap the camera power wire to the

PINK power output 1 wire.

33. Connect the audio out RCAs from

the Power/Video harness to the RCA

inputs on the 3.5mm to RCA adapter.

34. Plug in the 3.5mm jack into the

vehicle’s factory AUX input.

35. Mount the microphone to a loca-

on of your choice.

36. Connect the 3.5mm microphone

jack to the MIC input on the Power/

Video harness.

Crux Interfacing Solutions • 21541 Nordhoff Street, Unit C, Chatsworth, CA 91311

phone: (818) 609-9299 • fax: (818) 996-8188 • www.cruxinterfacing.com

rev.072419

6 of 13

INTERFACING SOLUTIONS

ACPBM-77Y

Smart-Play Integration with Rear-View Camera Input for

E & F Series BMW Vehicles with CIC Infotainment Systems

Crux Interfacing Solutions • 21541 Nordhoff Street, Unit C, Chatsworth, CA 91311

phone: (818) 609-9299 • fax: (818) 996-8188 • www.cruxinterfacing.com

rev.072419

7 of 13

INTERFACING SOLUTIONS

ACPBM-77Y

37. Connect the white wire with the

4-pin connector from the Power/CAN

harness to the UART port on the Smart-

Play module.

38. Connect the USB extenon cable to

the USB input on the Power/Video har-

ness for easier access when connecng

your smart-phone or USB.

39. Connect the Power/Video harness

to the POWER/VIDEO port on the

Smart-Play module.

41. Check the OSD sengs and make sure they match those on the next page.

Test the Back-Up camera. Put gear in reverse and check for rear camera image on

screen. Go to Smart-Play mode and test for funconality.

Once the cameras and Smart-Play validaon is complete, mount the ACPBM-77Y

and Smart-Play modules. And nally, reinstall all the components to their original

set-up.

40. Test the communicaon. Turn on

the ignion and check if LEDs are on.

Smart-Play Integration with Rear-View Camera Input for

E & F Series BMW Vehicles with CIC Infotainment Systems

Female 10-Pin

iDrive Connector

CAN-Low Pin 4 (Green)

CAN-High Pin 3 (Green/Orange)

CAN-Low (Blue)

CAN-High (Yellow)

F-Series

Power/CAN2

Harness

ACPBM-77Y Module

CAN Connecon for F-Series

Crux Interfacing Solutions • 21541 Nordhoff Street, Unit C, Chatsworth, CA 91311

phone: (818) 609-9299 • fax: (818) 996-8188 • www.cruxinterfacing.com

rev.072419

8 of 13

INTERFACING SOLUTIONS

ACPBM-77Y

OSD Menu

Use the following buons to enter the ACPBM-77Y OSD Menu:

BMW

OSD SETTINGS:

To ensure that Smart-Play works, make sure

these input sengs are in eect:

FRONTCAM (FVC) = SmartPhone

To retain the factory Back-Up Camera:

REARCAM (RVC) = OEM

To acvate an aermarket Back-Up Camera:

REARCAM (RVC) = ON

Press the menu button to

change the video sources

Crux Interfacing Solutions • 21541 Nordhoff St., Unit C, Chatsworth, CA 91311

phone: (818) 609-9299 • fax: (818) 996-8188 • www.cruxinterfacing.com

rev.070919

11 of 13

INTERFACING SOLUTIONS

ACPAD-81Y

Smart-Play Integration with Multi Camera Inputs & USB Player

for AUDI Vehicles with MMI MIB/MIB2 Systems

OSD Menu Menu Item

OSD

POS. X 0-xxx

POS. Y 0-xxx

Size Small Small OSD menu window

Large Large OSD menu windows

Osd TimeOut 2-20

Info Version X.XX.XX Displays the current SW-version

Factory Reset

CONNECTING THE SMART-PLAY INTERFACE:

plugged in to the USB port using the smartphone’s OEM charger/data cable. The USB port on the

ACPBM-77Y can be used to charge the Apple device or play videos or music from a USB thumb drive.

to the next enabled input. If all inputs are enabled the order is:

Rear CAM > Video Input (Smart-Play) > Repeat ...



ACPBM-77Y

To exit the Smart-Play menu, hold the “Menu” button for 3-5 sec.

Switch the vehicle’s audio source to the AUX source. This will allow us to hear the Smart-Play audio



Smart-Play Integration with Rear-View Camera Input for

E & F Series BMW Vehicles with CIC Infotainment Systems

NOTE: To exit back-up camera

image, press the iDrive button once

Use knob to navigate menu

and make selections

Hold for 3 sec to enter

OSD menu

to exit, hold for 3 sec

Hold for 3 sec to enter

Smart-Play menu

to exit, hold for 3 sec

Crux Interfacing Solutions • 21541 Nordhoff Street, Unit C, Chatsworth, CA 91311

phone: (818) 609-9299 • fax: (818) 996-8188 • www.cruxinterfacing.com

rev.072419

9 of 13

INTERFACING SOLUTIONS

ACPBM-77Y

Crux Interfacing Solutions • 21541 Nordhoff St., Unit C, Chatsworth, CA 91311

phone: (818) 609-9299 • fax: (818) 996-8188 • www.cruxinterfacing.com

rev.070919

12 of 13

INTERFACING SOLUTIONS

ACPAD-81Y

Smart-Play Integration with Multi Camera Inputs & USB Player

for AUDI Vehicles with MMI MIB/MIB2 Systems

1. Picture above shows the HOME screen of the Smart-

with a USB thumb drive plugged in to the USB port.

2. Using the iDrive knob of the vehicle, navigate the

cursor to the Bluetooth icon (scrolling right). Image above

will appears on the screen the BT device name and

pairing code (0000).

device and connect to “CRUX Smart-Play_XXXX”.

4. Once the ACPBM-77Y has connected via Bluetooth, it

5. Use the iDrive knob to navigate the cursor to the 6. Image above shows the “Home Screen” once the

smartphone is connected.

Smart-Play Integration with Rear-View Camera Input for

E & F Series BMW Vehicles with CIC Infotainment Systems

NOTE:

Make sure the audio source on the factory system is set to AUX mode (not AM/FM/Bluetooth). Also, if your smart-

phone is set to automatically connect to your factory bluetooth, make sure you void the connection. One way is to forget the

device (your vehicle) on your phone. This will avoid Smart-Play connection interferences. If you are using the wireless feature

and notice degraded audio or video quality, switch to the wired alternative, for it is a higher quality connection, unlike bluetooth.

Crux Interfacing Solutions • 21541 Nordhoff Street, Unit C, Chatsworth, CA 91311

phone: (818) 609-9299 • fax: (818) 996-8188 • www.cruxinterfacing.com

rev.072419

10 of 13

INTERFACING SOLUTIONS

ACPBM-77Y

Video-In-Motion Function

It is possible to ac�vate and deac�vate the video-in-mo�on in the OSD menu “MISC” (Opera�on of the OSD:

see chapter “OSD-Opera�on”).

OSD-Menu

Menu Item

Setting

Description

MISC VIM

Video-In-Mo�on ac�vated

OFF

Video-In-Mo�on deac�vated

NOTE: The Video-In-Mo�on func�on is permanently ac�ve without disturbing the naviga�on performance.

Selecting the Interface as Current AV Source

BMW 2-Button iDrive Mini 2-Button iDrive

A Long press of the Menu-button will select the interface as current video source.

A Short press of the CD Button or the MENU Button will switch the video sources (cameras or other video

source). Each short press will switch to the next enabled input. If all inputs are enabled the order is:

FRONT CAM



REAR CAM



…

Inputs which are not enabled are skipped.

CCC Navigation Screen

10 / 10

Rev.040816

Smart-Play Integration with Rear-View Camera Input for

E & F Series BMW Vehicles with CIC Infotainment Systems

Display sengs for Smart-Play

Adjust brightness, contrast, and saturaon for a more dened image.

To get to the Display menu, scroll to the SETTING icon in

the Smart-Play HOME menu, and select it.

Once in the SETTING menu, scroll to the Display submenu

and adjust the brightness, contrast, and saturaon to

your desired values.

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Accesorios para automóviles de Crux

Crux

Crux VIMGM-94M Manual de usuario

Crux

Crux BEECR-35D Manual de usuario

Crux

Crux RVCCH-75E Manual de usuario

Crux

Crux Sightline RVCAD-81B Manual de instrucciones

Crux

Crux Sightline RVCCH-75E Manual de usuario

Crux

Crux SWRGM-49L Manual de usuario

Crux

Crux CFD-03E Manual de usuario

Crux

Crux Sightline RVCVW-73 Manual de usuario

Crux

Crux MG-3 Manual de usuario

Crux

Crux Sightline VIMGM-94 Manual de usuario

Crux

Crux Sightline RVCAD-81 Manual de usuario

Crux

Crux Sightline VIMCF-93C Manual de usuario

Crux

Crux RVCCH-75 Manual de usuario

Crux

Crux Sightline MRVBM-77Q Manual de usuario

Crux

Crux Sightline VIMMB-85N Manual de usuario

Crux

Crux BTI-ISO Manual de usuario

Crux

Crux BEECR-35P Manual de usuario

Crux

Crux RVCAD-81T Manual de usuario

Crux

Crux RVCMZ-72D Manual de usuario

Crux

Crux Sightline PCM-3 Manual de usuario

Crux

Crux ACPBM-77X Manual de usuario

Crux

Crux ACPAD-01W Manual de usuario

Crux

Crux VIMBM-86B Manual de usuario

Crux

Crux Sightline RVCHN-76D Manual de usuario

Manuales populares de Accesorios para automóviles de otras marcas

James Baroud

James Baroud Odyssey Manual de usuario

Motorola

Motorola i50sx Manual de usuario

Yakima

Yakima 9MM STANDARD BIKE MOUNT Manual de usuario

Feniex

Feniex T3 Manual de usuario

Renault

Renault 77 11 423 180 Manual de usuario

Kia

Kia E8300-4D000 Manual de usuario

Brink

Brink 756843 Manual de usuario

Whispbar

Whispbar K085W Manual de usuario

v.link

v.link CI-VL2-PC-HSD Manual de usuario

Viking

Viking Stack-Rack Guía de configuración rápida

Aries

Aries 203015 Manual de usuario

Choetech

Choetech AT0005 Manual de usuario

ZZ2

ZZ2 ZZAIR-PRO Manual de usuario

Holman

Holman 4A80L Manual de usuario

Thule

Thule 2075 Manual de usuario

Motorola

Motorola T325 Manual de usuario

TAUBENREUTHER

TAUBENREUTHER 16-3950 Guía de instalación

DV8

DV8 FBJL-02 Manual de usuario