Cross Technologies 4116-31-184 Manual de usuario

Instruction Manual

Model 4116-31-184

Tri-Band Block Downconverter

Weatherized Unit

August 2021, Rev. A

Data, drawings, and other material contained herein are proprietary to Cross Technologies, Inc., but may be

reproduced or duplicated without the prior permission of Cross Technologies, Inc. for purposes of operating

the equipment. Printed in USA.

When ordering parts from Cross Technologies, Inc., be sure to include the equipment model number,

equipment serial number, and a description of the part.

CROSS TECHNOLOGIES, INC.

6170 Shiloh Road

Alpharetta, Georgia 30005

(770) 886-8005 • FAX (770) 886-7964 • Toll Free 888-900-5588

WEB www.crosstechnologies.com

E-MAIL [email protected]

INSTRUCTION MANUAL

MODEL 4116-31-184 Tri-Band Block Downconverter, Weather Resistant*

TABLE OF CONTENTS PAGE

Warranty 2

1.0 General 3

1.1 Equipment Description 3

1.2 Technical Characteristics 4

2.0 Installation 6

2.1 Message Protocol 6

2.2 M&C Commands 7

2.3 M&C Queries 8

2.4 Ethernet Interface Installation 10

2.4.1 Methods of Connection 10

2.4.2 Ethernet Configuration 10

2.4.3 Webpage M&C 12

2.4.4 SNMP Configuration 13

2.6 Physical Interface 16

2.7 Installation/Operation 17

WARRANTY - The following warranty applies to all Cross Technologies, Inc. products.

All Cross Technologies, Inc. products are warranted against defective materials and

workmanship for a period of one year after shipment to customer. Cross Technologies,

Inc.’s obligation under this warranty is limited to repairing or, at Cross Technologies, Inc.’s

option, replacing parts, sub-assemblies, or entire assemblies. Cross Technologies, Inc. shall

not be liable for any special, indirect, or consequential damages. This warranty does not

cover parts or equipment which have been subject to misuse, negligence, or accident by the

customer during use. All shipping costs for warranty repairs will be prepaid by the

customer. There are not other warranties, express or implied, except as stated herein.

CROSS TECHNOLOGIES, INC.

6170 Shiloh Road

Alpharetta, Georgia 30005

(770) 886-8005 • FAX (770) 886-7964 • Toll Free 888-900-5588

WEB www.crosstechnologies.com • E-MAIL [email protected]

4116-31-184 Manual, Rev. A Page 2 08/19/21

MODEL 4116-31-184 Tri-Band Block Downconverter, Weather Resistant*

1.0 General

1.1 Equipment Description

The 4116-31-184 Block Downconverter converts one of three RF bands to 0.95 - 2.05 GHz. Front panel LEDs

provide indication of DC Power, and PLL Alarm. The RF to L-band gain is +30 dB. Connectors are Type N

female for the L-band, RF and RF Monitor and SMA female for the external reference input and reference

output. Gain, band select, and internal 10 MHz frequency are controlled by the Ethernet M&C or via the

Status/Control connector. In AUTO, the 10 MHz reference stays in external if the external level is in the +2 to

+8 dBm range. It is powered by a 100-240 ± 10% VAC power supply, and in a 8” W X 6” H X 16” D Weather

Resistant* enclosure.

NOTE: *Weather Resistant enclosures are designed to be water resistant for installation in an outdoor enclosure/antenna hut OR

mounted outdoors on an antenna assembly at their specified temperature ranges. They are designed to be located “out in the

elements” (water, sleet, snow, etc.) but they are not designed to be “submerged under water”. If an extended temperature range is

required, there is an Extended Temperature option (Option W21; -30˚C to +60˚C) available at an additional cost. Contact Cross for

quote.

L-BAND OUT

10M IN

STATUS /

CONTROL ETHERNET

RF INPUT

J1 J2

POWER

ALARM

J3 J4

10 M OUT

FUSE

AC IN

J6 J7

RF MON

MODEL 4116 TRI-BAND

DOWNCONVERTER

CROSS TECHNOLOGIES INC.

• •

• • • •

• • • • • •

• • • •

• •

FIGURE 1.1 Model 4116-31-184 Tri-Band Block Downconverter Front Panel

4116-31-184 Downconverter

Block Diagram

L-BAND

OUT

5.85

18.4

GHz

EXT

10 M

5.85 to 6.425 GHz BP

10 M

PLLS

13.75 to 14.5 GHz BP SW,PLL,ATT,

VCC CONTROL

M&C

CONTROLLER

17.3 to 18.4 GHz BP

10 M

MON

+10

MON 1 - 7.90

2 - OFF

3 - OFF

1 - 12.8

2 - 12.8

3 - OFF

1 - OFF

2 - OFF

3 - 16.35

FIGURE 1. Model 4116-31-184 Tri-Band Block Downconverter Block Diagram

4116-31-184 Manual, Rev. A Page 3 08/19/21

1.2 Technical Characteristics

Continued on page 5...

4116-31-184 Manual, Rev. A Page 4 08/19/21

<-40 dBc at 0 dBm out, 0.95 to 2.50 GHz out (Band 3); at Gmax

Harmonics

In Band

+30 ±3 dB, ( 0 to +30 dB variable in 0.5± 0.5 dB dB steps)

Gain @ Fc

±2 dB, over RF band; ± 0.5 dB, 40 MHz BWFre

uenc

Res

onse

Channel Characteristics

LO Characteristics

± 0.05

m maximum over tem

internal reference; external reference in

utFre

uenc

Accurac

Non-invertin

Fre

uenc

Sense

<-50 dBc for two carriers at 4 MHz spacing, each at -5 dBm out; at Gmax

Intermodulation

<-50 dBm

0.5 - 0.94 GHz and 2.06 - 2.50

;

GHz

;

at GmaxS

urious

Out of Band

SIGNAL RELATED <-50 dBc, -20 to 0 dBm out;

SIGNAL INDEPENDENT,<-60 dBm; all at Gmax

urious, Inband

ut = +2 dBm to +8 dBm in

Monitor Out

ut = in

ut level ± 1.0 dB

50 ohms10 MHz Level In/Mon

Band S

ecificLO Fre

uenc

> 60 dB

minimumIma

e Re

ection

Controls

Indicators

Green LEDPower

Gain, band select and internal 10 MHz frequency via

Ethernet M&C or Status/Control Connector

Gain, Band, 10M Fre

uenc

Red LED, External Contact ClosurePLL, Alarm

TABLE 1.0 4116-31-184 Downconverter Specifications*

Band 3 - 17.3 to 18.4

Band 2 - 13.75 to 14.5

+10 dBm, at maximum

ainOut

ut 1 dB Com

ression

Band 3 - 0.95 to 2.05

Band 2 - 0.95 to 1.70

-20 to -40 dBmIn

ut Level Ran

e15 dB maximum

ainNoise Fi

ure, Maximum

Band 1 - 5.85 - 6.425Fre

uenc

(

GHz

)

-20 to 0 dBmOut

ut Level Ran

Out

ut Characteristics

Band 1 - 0.95 to 1.525Fre

uenc

(

GHz

)

50Ω/ 12 dBIm

edance / Return Loss

50Ω/ 12 dBIm

edance / Return Loss

1.2 Technical Characteristics (continued)

Size 8” Wide X 6” High X 16” Deep Weather Resistant* Enclosure

Power 100-240 ±10% VAC, 47 - 63 Hz, 25 watts max./ FCI Clipper Series CL1M1102 Connector

*Weather Resistant enclosures are designed to be water

resistant for installation in an outdoor enclosure/antenna hut

OR mounted outdoors on an antenna assembly at their

specified temperature ranges. They are designed to be located

“out in the elements” (water, sleet, snow, etc.) but they are not

designed to be “submerged under” water.

If an extended temperature range is required, there is an

Extended Temperature option (Option W21; -30˚C to +60˚C)

available at an additional cost. Contact Cross for quote.

4116-31-184 Manual, Rev. A Page 5 08/19/21

RJF6GRJF21B

Ethernet Connector / RJ45

CL1F1101CL1M1102

AC In

ut Connector**

MS3116F14-18PMS3112E14-18S

Status/Control Connector

Matin

Connector P/NConnector P/NConnectors*

* All cable connectors are Weather resistant. ** AC mating connector PROVIDED preassembled onto standard NEMA 5-15 U.S. power cord.

M&C Interface

Additional Connector S

ecifications*

RS232/422/485;

Ethernet: Web

Browser, SNMP &

TCP/IP STD.

10 MHz In/Out

SMA (Female)

50 Ω

L-Band Out

Type N (F)

50 Ω

RF In/ Mon

Type N (F)

50 Ω

2.0 Installation

The 4116-31-184 Tri-Band Block Downconverter consists of a 8”W X 6 “H X 16”D Weather resistant*

enclosure. A switching, ± 12, +24, +5 VDC power supply provides power for the internal assemblies.

The 4116-31-184 can be secured to a mounting plate using the 4 holes on the bottom of the front and rear

panels. See Figure 2.5 for mounting dimensions.

2.0.1 Connection to AC Input Power

The 4116-31-184 utilizes a pre-assembled AC power input cable as described below.

4115-

1 Power Input Connector, FCI Clipper Series, CL1M1102 & Crimp Pins

Matin

Mating Connector FCI Clipper Series, CL1F1101, Crimp Pins

and CCL101021

and CL101021 Backshell

Pin Input Connector Pin Description

1 100-240 ±10% VAC, 47-63 Hz, 20 watts max.

2 Neutral

3 Ground

2.1 Message Protocol

The serial format for the RS232/RS422/RS485 port is 9600 baud, 8 data bits, no parity, and 1 stop bit.

All messages consist of ASCII printable characters so standard terminals and terminal emulator programs may

be used to control and monitor the unit. All messages begin with the open bracket character “{”(ASCII 0x7B)

and end with the close bracket character “}” (ASCII 0x7D). Messages consisting of commands to set or change

operating parameters and modes of the unit begin with “C” (ascii 0x43) followed by a command specific

character. Messages consisting of queries to report operating parameters and modes begin with “S”

(ASCII 0x53) followed by a parameter specific character.

4116-31-184 Manual, Rev. A Page 6 08/19/21

2.2 M&C Commands

The following tables summarize the commands and status queries applicable to the

4116-31-184 Tri-Band Block Downconverter.

*PLEASE NOTE: The two character {aa} prefix, shown in the table below, is present ONLY when RS485 is selected.

Table 2.0 Model 4116-31-184 M&C Commands

select

auto

reference

x = 2 to select external reference

x = 1 to select internal reference

where:{aaCEx}Set 10 MHz reference mode

Range: +2000 to -2000

select

RS232

xxxxx = 5 characters

where:{aaCOxxxxx}Set Int. 10 MHz reference offset

Range: 00 to 31

xx = 2 characters

where:{aaCRxx}Set RS485 address

x = 2 to select RS485

x = 1 to select RS422

where:

{aaCIx}

Set Serial Interface

Range: 000 to 300 (00.0 to 30.0 in 0.5 dB steps)

xxx = 3 characters

where:

{

aaCGxxx

}

Set

Gain

x = 3 to select band 3: in = (17.3 to 18.4 GHz)

out

(

950

2050

MHz

)

x = 2 to select band 2: in = (13.75 to 14.5 GHz)

out

(

950

1700

MHz

)

x = 1 to select band 1: in = (5.85 to 6.425 GHz)

out

(

950

1525

MHz

)

where:

{

aaCBx

}

Set

Fre

uenc

Band

DescriptionSyntaxCommand

Table 2.0: Model 4116-31-184 M&C Commands

4116-31-184 Manual, Rev. A Page 7 08/19/21

2.3 M&C Queries

Table 2.1 Model 4116-31-184 M&C Commands

x = 0 if RS232 is selected

Example: {aaSG245} indicates the current gain

setting is 24.5 dB

Range: 00 to 31

RS485

selected

Auto

MHz

reference

selected

xx = 2 characters

Returns {aaSAxx} where:

{

aaSR

}

RS485 address

x = 1 if RS422 is selected

Returns {aaSIx} where:{aaSI}

Serial Interface

x = 2 if External 10 MHz reference is selected

x = 1 if Internal 10 MHz reference is selected

Returns {aaSEx} where:{aaSE}

10 MHz reference

Range: 0 to 300 ( in 0.5 dB steps)

xxx = 3 characters

Returns {aaSGxxx} where:

{

aaSG

}

Gain

x = 3 if band 3 is selected: in = (17.3 to 18.4 GHz)

out

(

950

2050

MHz

)

x = 2 if band 2 is selected: in = (13.75 to 14.5 MHz)

out

(

950

1700

MHz

)

x = 1 if band 1 is selected: in = (5.85 to 6.425 GHz)

out

(

950

1525

MHz

)

Returns {aaSBx} where:

{

aaSB

}

Fre

uenc

Band

DescriptionSyntaxCommand

Table 2.1: Model 4116-31-184 M&C Queries

Continued on page 9...

4116-31-184 Manual, Rev. A Page 8 08/19/21

Table 2.1 Model 4116-31-184 M&C Commands (continued from page 8)

Unit Status

y = oven status: 0 = normal, 1 = oven warmup

x = ref. source: 1 = internal, 2 = extenal

summar

alarm:

off,

returns

{

aaSSwx

where:

{aaSS}

x = 0 if no summary alarm, x = 1 if summary alarm

returns

{

aaSVxxxxxxxx

yyyy}

where:

{aaSV}

Model

and

firmware

revision

Ran

+2000

-2000

xxxxx

characters

yyyy = unit firmware rev.

xxxxxxxx = unit model number

Range (-99 to +99) degrees Celsius

xxx = 3 characters

Returns {aaSTxxx} where:{aaST}

Internal Temperature

Returns {aaSAx} where:

{

aaSA

}

Summar

Alarm

Returns {aaSOxxxxx} where:

{

aaSO

}

Int.

MHz

reference

offset

DescriptionSyntaxCommand

Table 2.1: Model 4116-31-184 M&C Queries - Continued...

4116-31-184 Manual, Rev. A Page 9 08/19/21

2.4 ETHERNET Interface Installation and Operation

The 4116-31-184 Tri-Band Block Downconverter is equipped with a 10/100 Base-T compatible Ethernet

interface for control and monitoring of its operating parameters. An HTML script interface allows the user to

monitor and control the converter using a standard web browser. SNMP (Simple Network Management

Protocol) is also supported. Contact Cross Technologies for the SNMP MIB file.

2.4.1 Methods of Connection

Directly Connected to a PC:

For control from a local PC, attach the 4116-31-184’s Ethernet port to the Ethernet network connector on the

PC using a crossover RJ-45 cable.

LAN Connection

For LAN connections, attach the 4116-31-184 Ethernet port to the LAN using a normal RJ-45 cable.

Use any PC on the LAN to connect to the 4116-31-184.

2.4.2 Ethernet Configuration

Each 4116-31-184 must be configured with an appropriate IP address, Netmask, and Gateway assigned by your

network manager. The 4116-31-184 is set at the factory with a static address that is written on a tag attached to

the unit. The device server in the 4116-31-184 has a built in HTTP based configuration manager that is used to

configure network settings. To access the configuration manager open a web browser and enter the IP address

of the 4116-31-184 in the browser's address field. The window shown in Figure 2-A will appear. As

delivered, there is no password set. Choose your user name and password here or leave those fields blank and

click OK to proceed to the configuration manager web page.

4116-31-184 Manual, Rev. A Page 10 08/19/21

Tabla de contenidos

Otros manuales de Convertidor de medios de Cross Technologies

Cross Technologies

Cross Technologies 2017-93 Manual de usuario

Cross Technologies

Cross Technologies 2116-21-1014 Manual de usuario

Cross Technologies

Cross Technologies 2116-140T120 Manual de usuario

Cross Technologies

Cross Technologies 2015-03A Manual de usuario

Cross Technologies

Cross Technologies 2015-05 Manual de usuario

Cross Technologies

Cross Technologies 2115-275-1845 Manual de usuario

Cross Technologies

Cross Technologies 2416-x02 Manual de usuario

Cross Technologies

Cross Technologies 2017-0923 370 Series Manual de usuario

Cross Technologies

Cross Technologies 2005 Manual de usuario

Cross Technologies

Cross Technologies 2016-03A Manual de usuario

Cross Technologies

Cross Technologies 2009-2425-1750 Manual de usuario

Cross Technologies

Cross Technologies 3116-22-23 Manual de usuario

Cross Technologies

Cross Technologies 4116-285-2450 Manual de usuario

Cross Technologies

Cross Technologies 2016-95 Manual de usuario

Cross Technologies

Cross Technologies 2117-8485 Manual de usuario

Cross Technologies

Cross Technologies 2117 Manual de usuario

Cross Technologies

Cross Technologies 2115-122 Manual de usuario

Cross Technologies

Cross Technologies 2416 25 Series Manual de usuario

Cross Technologies

Cross Technologies 3116-145-1600 Manual de usuario

Cross Technologies

Cross Technologies 2116-182193 Manual de usuario

Cross Technologies

Cross Technologies 2015-7075 Manual de usuario

Cross Technologies

Cross Technologies 4115-300 Manual de usuario

Cross Technologies

Cross Technologies 2016-25-01 Manual de usuario

Cross Technologies

Cross Technologies 1584 Manual de usuario

Manuales populares de Convertidor de medios de otras marcas

SoundTraxx

SoundTraxx Blunami BLU-2200 Manual de usuario

SPROLINK

SPROLINK VA1 Manual de usuario

Acclaim Lighting

Acclaim Lighting DDC-1-AC Manual de usuario

Nikon

Nikon AF-S TC-20E III Manual de usuario

Axis

Axis AXIS Q7406 Manual de usuario

Omega

Omega TAC80B-J Manual de usuario

Zoom

Zoom Thunderbolt TAC-2R Manual de usuario

OST

OST iConverter 10/100M Manual de usuario

Vertiv

Vertiv Netsure Manual de usuario

birddog

birddog MINI Manual de usuario

Roland

Roland GI-10 Manual de usuario

Wallenstein

Wallenstein WX310 Manual de usuario

Pace

Pace MSS 200-1 Manual de usuario

Solar Converters

Solar Converters EQ 12/24-50 Manual de usuario

CYP

CYP EL-7400V Manual de usuario

TIE

TIE MIDI 1i1o Manual de usuario

DCS

DCS Vivaldi Upsampler Manual de usuario

Westermo

Westermo MCW-211 SERIES Manual de usuario