Cross Technologies 1584 Manual de usuario

Instruction Manual

Model 1584-18/18S

RF Splitter

November 2018, Rev. C

MODEL 1584 CROSS TECHNOLOGIES INC.

POWER

SPLITTER

BLNB VOLTAGE

GND +DC

Data, drawings, and other material contained herein are proprietary to Cross Technologies, Inc.,

but may be reproduced or duplicated without the prior permission of Cross Technologies, Inc.

for purposes of operating the equipment.

When ordering parts from Cross Technologies, Inc., be sure to include the equipment

model number, equipment serial number, and a description of the part.

CROSS TECHNOLOGIES, INC.

6170 Shiloh Road

Alpharetta, Georgia 30005

(770) 886-8005

FAX (770) 886-7964

Toll Free 888-900-5588

WEB www.crosstechnologies.com

E-MAIL [email protected]

INSTRUCTION MANUAL

MODEL 1584-18/18S, 16-Way Splitter

TABLE OF CONTENTS PAGE

Warranty 2

1.0 General 3

1.1 Equipment Description 3

1.2 Technical Characteristics 4

2.0 Installation 5

2.1 Mechanical 5

2.2 Rear Panel Input/Output Connectors 6

2.3 Front Panel Monitors and Indicators 6

2.4 Operation 7

2.5 Environmental Use Information 8

WARRANTY - The following warranty applies to all Cross Technologies, Inc. products.

All Cross Technologies, Inc. products are warranted against defective materials and

workmanship for a period of one year after shipment to customer. Cross Technologies,

Inc.’s obligation under this warranty is limited to repairing or, at Cross Technologies, Inc.’s

option, replacing parts, subassemblies, or entire assemblies. Cross Technologies, Inc. shall

not be liable for any special, indirect, or consequential damages. This warranty does not

cover parts or equipment which have been subject to misuse, negligence, or accident by the

customer during use. All shipping costs for warranty repairs will be prepaid by the

customer. There are no other warranties, express or implied, except as stated herein.

CROSS TECHNOLOGIES, INC.

6170 Shiloh Road

Alpharetta, Georgia 30005

(770) 886-8005

FAX (770) 886-7964

Toll Free 888-900-5588

WEB www.crosstechnologies.com

E-MAIL [email protected]

1584-18/18S Manual_ Rev. C Page 2 11/07/18

MODEL 1584-18/18S Splitter

1.0 General

1.1 Equipment Description

The Model 1584-18/18S* is one eight-way, 0.95 - 2.05 GHz, 0 dB gain splitter in a 1RU rack mount chassis

with redundant 100-240 ± 10% VAC power supplies. The splitter provides fused LNB DC power insertion and

surge protection on the RF input, and provides excellent RF characteristics. The splitter has eight outputs on the

back panel, and fused LNB power can be inserted on the input. Two individual 100-240 ± 10% VAC input

power supplies provide diode OR’d redundant power to the unit*. The LNB power line is separately fused. A

surge suppressor on the splitter input protects against high voltage transients. On the front panel, two green

LED’s indicate the presence of DC voltage from each of the two power supplies, and another green LED

indicates LNB power insertion. LNB voltage test points are also provided on the front panel to monitor the LNB

voltage. *LNB Power Insertion feature NOT available on 1584-18S model.

MODEL 1584 CROSS TECHNOLOGIES INC.

POWER

SPLITTER

BLNB VOLTAGE

GND +DC

FRONT PANEL*

AC A AC B

GND

J2J3J4

J5J6J7J8J9

J10J11J12

J17 J13J14J15J16

FUSE F1

SPLITTER

OUT OUTOUTOUTOUTOUTOUT OUTOUTOUT OUT OUTOUTOUT OUTOUT

REAR PANEL*

FIGURE 1.1 MODEL 1584-18/18S FRONT AND REAR PANELS

1584-18/18S Block Diagram

AMP

INS

SURGE

SUPPRESS

FUSE

8 WAY

SPLITTER

OUT 1

OUT 2

OUT 8

1 - 2

GHz

1 - 2 GHz OUT

FIGURE 1.2 MODEL 1584-18/18S Block Diagram

*NOTE: Model 1584-18/18S has a single non-redundant, switching power supply.

1584-18/18S Manual_ Rev. C Page 3 11/07/18

1.2 Technical Characteristics

TABLE 1.0 1584-18/18S SPECIFICATIONS

Characteristics Specifications**

Input Characteristics

Input Impedance 75Ω(50Ω, Option -D)

Return Loss 12 dB minimum; 14 dB typical

Input Level -20 dBm total maximum

(No Damage +10 dBm)

Output Characteristics

Impedance 75Ω(50Ω, Option -D)

Return Loss 12 dB minimum.; 14 dB typical

In-Band Characteristics

Gain +0 dB ±1.0 dB

Frequency Response ± 1.0 dB; 0.95 to 2.05 GHz

± 0.5 dB, any 20 MHz increment

Port to Port Isolation > 18 dB, 20 dB typical

Indicators

AC Power Green LED indicates DC voltage prior to diode OR

LNB DC Voltage Green LED indicates LNB power insertion on splitter input (J17)

Other

LNB DC Voltage 22 ± 2 VDC

Output LNB current 300 ma, maximum

Surge Suppressor SiDACTOR

RF connectors Type-F (female)

AC Power Redundant switching power supplies,

100-240 ± 10% VAC, 4 -63 Hz, 30 watts maximum

*NOTE: Model 1584-18S has a single non-redundant, Switching

Power Supply and does NOT provide the LNB Power Insertion Feature.

Mechanical 19 inch standard chassis 1.75” high X 12” deep

Options

-B 75ΩBNC, RF Connectors

-D 50ΩBNC, RF Connectors

-E External 10 MHz Reference Input with Insertion

-W9 DC (24 vdc/2.5A) Power By-pass

**+10˚C to +40˚C; Specifications subject to change without notice.

1584-18/18S Manual_ Rev. C Page 4 11/07/18

2.0 Installation

2.1 Mechanical - The 1584-18/18S consists of one RF printed circuit board (PCB) housed in a 1 RU (1.75 inch

high) by 12 inch deep chassis. Redundant, switching, +24 VDC power supplies with the DC output diode OR’d

provide redundant power for the internal and external amplifiers and LEDs. (Model 1584-18/18S has a single

non-redundant, switching power supply). Connectors are type F, female for the RF connections (BNC, female

option -B or -D). The 1584-18/18S can be secured to a rack using the 4 holes on the front panel. Figure 2.0

shows how the 1584-18/18S is assembled. J25 connects DC Power to the fuse as shown and J30 and J29

connect the DC voltage from the power supplies to the PCB as shown.

POWER

SUPPLY

2 1

J29

+24 PS IN (AC A)

PIN 1, +24 VDC

PIN 2, GROUND

POWER

SUPPLY

NOTE:

Model 1584-18S has

a single

non-redundant,

switching power

supply.

J30

+24 PS IN (AC B)

PIN 1, +24 VDC

PIN 2, GROUND

J25

LNB FUSE

PIN 1, LNB SIDE

PIN 2, +22 VDC SIDE

2 1

FIGURE 2.0 1584-18/18S MECHANICAL ASSEMBLY

1584-18/18S Manual_ Rev. C Page 5 11/07/18

2.2 Rear Panel Input/Output Connectors

The input and output connectors on the rear panel are shown in Figure 2.1.

CAUTION! IF A FUSE IS INSTALLED IN THE FUSE F1 HOLDER, +22 VDC WILL APPEAR

ON THE SPLITTER INPUT CONNECTOR (J17) CENTER PIN.

AC A INPUT

100-240 ±10% VAC,

47-60 HZUses 2 amp

Slow Blo, 5mm fuse.

J17 - SPLITTER INPUT

Type F (female) 75 Ω.

See Table 2.0 for other

connector options.

J16, J15, J14, J13, J12, J11, J10, J9 - SPLITTER OUTPUTS

Type F (female) 75Ω. Terminate when not used.

See Table 2.0 for other connector options.

AC B INPUT

100-240 ±10% VAC, 47-

60 HZ. Uses 2 amp

Slow Blo, 5mm fuse.

AC A AC B

GND

J2J3J4J5J6J7J8J9

J10J11J12

J17 J13J14J15J16

FUSE F1

SPLITTER

FIGURE 2.1 1584-18/18S REAR PANEL

*NOTE: Model 1584-18/18S has a single non-redundant, switching power supply.

External 10 MHz Reference Input, with insertionE -

DC (24 vdc / 2.5A) Power SupplyW9 -

BNC, 50ΩD -

BNC, 75ΩB -

STD Type F, 75Ω

RF ConnectorsOption

Table 2.0 RF Connector Options

2.3 Front Panel Monitors and Indicators

Figure 2.2 shows the front panel monitors and indicators.

DS6 - POWER LED B*

Lights green when DC voltage

is present from AC B power supply.

TP1 - +DC TEST POINT

Used to measure the LNB voltage.

22 ±2 VDC typical

DS5 - POWER LED A

Lights green when DC

voltage is present from AC A

power supply.

TP5 - GND TEST POINT

Used to measure the LNB voltage. DS1 - LNB VOLTAGE LED

Lights Green when LNB voltage is present

on the Splitter input (J17) center pin.

POWER

BLNB VOLTAGE

GND +DC

MODEL 1584

SPLITTER CROSS TECHNOLOGIES INC.

FIGURE 2.2 1584-18/18S FRONT PANEL

1584-18/18S Manual_ Rev. C Page 6 11/07/18

2.4 Operation

1. Connect RF cables to the 1584-18/18S (See Section 2.2).

2. IF DC VOLTAGE IS REQUIRED ON THE SPLITTER RF INPUT (J17) CENTER CONDUCTOR,

install 1/4”, 0.5 amp fast blo fuses in the FUSE F1 holder

3. Connect 100-240 ± 10% VAC, 47 - 63 Hz to AC A and AC B on the back panel and observe

A and B LEDs are lit on the front panel.*

4. Monitor DC voltage to the external LNB amplifier (Front panel Green ON LED should be lit if

LNB fuse is installed in the rear panel fuse holder) to insure proper voltage.

CAUTION! IF A FUSE IS INSTALLED IN THE FUSE F1 HOLDER, +22 VDC WILL APPEAR

ON THE SPLITTER INPUT CONNECTOR (J17) CENTER PIN.

NOTE: FOR OPTIMUM PERFORMANCE, THE SPLITTER PORTS SHOULD BE TERMINATED

WITH 75 OHM TYPE F TERMINATION WHEN NOT USED.

AC Fuse - The fuse is a 5mm, 2 amp slow blo and is inserted in the far slot in the drawer below the AC

input as shown in Figure 2.6. There is a spare fuse in the near slot. If a fuse continues to open, the power

supply is most likely defective. Note that each power supply module within the chassis also has a fuse

but failure of this fuse indicates the power supply may be defective.

AC Fuse - 2 amp slow blow (Type T),

5 mm X 20 mm

FUSE DRAWER

SPARE FUSE

INPUT

100-240± 10%VAC

47-63 Hz

2A MA

FUSE

TYPE T 2A GDC

250 VOL

FOR 100 - 240 V~

FIGURE 2.6 FUSE LOCATION AND SPARE FUSE

1584-18/18S Manual_ Rev. C Page 7 11/07/18

2.5 Environmental Use Information

A.Rack-Mounting - To mount this equipment in a rack, please refer to the installation instructions

located in the user manual furnished by the manufacturer of your equipment rack.

B. Mechanical loading - Mounting of equipment in a rack should be such that a hazardous condition

does not exist due to uneven weight distribution.

C.Elevated operating ambient temperature - If installed in a closed or multi-unit rack assembly,

the operating ambient temperature of the rack may be greater than room ambient temperature.

Therefore, consideration should be given to Tmra.

D. Reduced air flow - Installation of the equipment in a rack should be such that the amount of air flow

required for safe operation of the equipment is not compromised. Additional space between unit

may be required.

E. Circuit Overloading - Consideration should be given to the connection of the equipment to the supply

circuit and the effect that overloading of circuits could have on over current protection and supply wiring.

Appropriate consideration of equipment name plate rating should be used, when addressing this concern.

F. Reliable Earthing - Reliable earthing of rack-mounted equipment should be maintained. Particular

attention should be given to supply connections other than direct connection to the Branch

(use of power strips).

G. Top Cover - There are no serviceable parts inside the product so, the Top Cover should not be removed.

If the Top Cover is removed the ground strap and associated screw MUST BE REINSTALLED

prior to Top Cover screw replacement. FAILURE TO DO this may cause INGRESS and/or EGRESS

emission problems.

1584-18/18S Manual_ Rev. C Page 8 11/07/18

CROSS TECHNOLOGIES, INC.

6170 Shiloh Road

Alpharetta, Georgia 30005

(770) 886-8005

FAX (770) 886-7964

Toll Free 888-900-5588

WEB www.crosstechnologies.com

E-MAIL [email protected]

Printed in USA

1584-18/18S Manual_ Rev. C Page 9 11/07/18

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Convertidor de medios de Cross Technologies

Cross Technologies

Cross Technologies 2017-93 Manual de usuario

Cross Technologies

Cross Technologies 2017-03A Manual de usuario

Cross Technologies

Cross Technologies 2015-7075 Manual de usuario

Cross Technologies

Cross Technologies 2099-10 Manual de usuario

Cross Technologies

Cross Technologies 2115-275-1845 Manual de usuario

Cross Technologies

Cross Technologies 3016-2124 Manual de usuario

Cross Technologies

Cross Technologies 2016-75-213 Manual de usuario

Cross Technologies

Cross Technologies 2099-2424 Manual de usuario

Cross Technologies

Cross Technologies 2117-7172 Manual de usuario

Cross Technologies

Cross Technologies 2016-95 Manual de usuario

Cross Technologies

Cross Technologies 3116-145-1600 Manual de usuario

Cross Technologies

Cross Technologies 2017-03 Manual de usuario

Cross Technologies

Cross Technologies 3117-3338 720 Series Manual de usuario

Cross Technologies

Cross Technologies 4116-31-184 Manual de usuario

Cross Technologies

Cross Technologies 3016-1520-1200 Manual de usuario

Cross Technologies

Cross Technologies 2005-10 Manual de usuario

Cross Technologies

Cross Technologies 2016-25-01 Manual de usuario

Cross Technologies

Cross Technologies 2015-03A Manual de usuario

Cross Technologies

Cross Technologies 2116-21-1014 Manual de usuario

Cross Technologies

Cross Technologies 2415-x02 Manual de usuario

Cross Technologies

Cross Technologies 4116-31-2831 Manual de usuario

Cross Technologies

Cross Technologies 2016-1522 Manual de usuario

Cross Technologies

Cross Technologies 2015-123 Manual de usuario

Cross Technologies

Cross Technologies 3115-21-109 Manual de usuario

Manuales populares de Convertidor de medios de otras marcas

SoundTraxx

SoundTraxx Blunami BLU-2200 Manual de usuario

SPROLINK

SPROLINK VA1 Manual de usuario

Acclaim Lighting

Acclaim Lighting DDC-1-AC Manual de usuario

Nikon

Nikon AF-S TC-20E III Manual de usuario

Axis

Axis AXIS Q7406 Manual de usuario

Omega

Omega TAC80B-J Manual de usuario

Zoom

Zoom Thunderbolt TAC-2R Manual de usuario

OST

OST iConverter 10/100M Manual de usuario

Vertiv

Vertiv Netsure Manual de usuario

birddog

birddog MINI Manual de usuario

Roland

Roland GI-10 Manual de usuario

Wallenstein

Wallenstein WX310 Manual de usuario

Pace

Pace MSS 200-1 Manual de usuario

Solar Converters

Solar Converters EQ 12/24-50 Manual de usuario

CYP

CYP EL-7400V Manual de usuario

TIE

TIE MIDI 1i1o Manual de usuario

DCS

DCS Vivaldi Upsampler Manual de usuario

Westermo

Westermo MCW-211 SERIES Manual de usuario