CrimeStopper REVO-1 Series Manual de usuario

REVO-1 & REVO-4 SERIES

1 - Way Remote Start System

INSTRUCTIONS

CONGRATULATIONS on your choice of a Crimestopper Revo Start 1-Way Remote Start System.This system is

an RF Antenna Decoder that plugs directly into a Fortin or ADS Data module. No additional remote start module is

needed. The features of the system, depends on the vehicle and data module used. This system requires a Fortin

or ADS data module with a programmer to load correct vehicle software. You willneed the vehicle install guide from

Fortin or ADS iDatalink website. Many vehicles have a “Plug n Play” T harness available to simplify the installation.

The remotes needtobeprogrammed after installation of data module beforeoperation. If any questions arise,

contact your installation dealer or Crimestopper Security Products.

CRIMESTOPPER SECURITY PRODUCTS

600 S. ROCKFORD DR., TEMPE, AZ 85281

REV 09-2015

This device complies with FCC Rules part 15. Operation is

subject to the following two conditions: 1) This device may not

cause interference, and (2) this device must accept any

interference that may be received, including interference that

may cause undesired operation. The manufacturer is not

responsible for any radio or TV interference caused by

unauthorized modification to this equipment. Such modification

could void the user's authority to operate the equipment.

USING THE REMOTE TRANSMITTER

REVO-1 Series REVO-4 Series

For REVO-1 Series

The transmitter supplied has one Start button.

For REVO-4 Series

REVO-4

Aux Channels

AUX 1 = Trunk + Lock

AUX 2 = Trunk + Unlock

AUX 3 = Trunk + Start

AUX 4 = Lock + Start

VEH

UNLOCK

START

DISARM /

ARM /

LOCK

TRUNK

VEHICLE

SELECT

VEH 1 = Blue LED

VEH 2 = Red LED

The transmitter supplied with this system has 5 buttons - Lock, Unlock, Trunk Release, Vehicle Select and Start.

This remote can control up to 4 AUX functions thru data depending on the vehicle and data module. This is typically

used for operating the left and right sliding doors and Gas Cap release. Consult with your installer about the

optional AUX functions.

BATTERY REPLACEMENT

To replace the battery on a REVO 1 Series 1 button remote:

Simply remove the screw on the back of the transmitter and slide the cas apart as shown. Remove the (2) CR-1620

Lithium batteries and replace. Put the case back together and tighten the screw.

BATTERY REPLACEMENT

The Remote Control uses two CR-2025 Lithium 3 Volt Batteries. Simply remove the Phillips screw located behind

key ring (see diagram below). Use a small screw driver as shown in Figure 2 to remove the back cover. Slide old

batteries out. Insert the new batteries into plastic cover and slide into place with the (+) end facing up. The plastic

cover keeps the batteries from shorting out against the side of metal housing.

VEH

UNLOCK

START

DISARM /

ARM /

LOCK

TRUNK

Vehicle SelectCR2025

2 Screws

Back Cover

Remove

2 Screws &

Slide Key Ring Off

Blue / Red

To Replace the Battering in the REVO 4 Series

Fig. 1 Fig. 2 Fig. 3

TRANSMITTER PROGRAMMING

ADS iDatalink Programming:

Fortin EVO-ALL Programming:

1. Insert the key into the ignition, if you have a proximity key just be sure you can start the vehicle.

2. This step must be completed within 7 seconds: Cycle the ignition (5) times with the 5th time leaving it in the

ON position.

3. The parking lights will flash (1) time (this is only if the parking lights are offered through the integration module or

if connected via an output from the module) confirming you have entered the remote learning sequence.

4. This step must be completed in 5 seconds: Press the Start button on the REVO-1 or Lock button on the

REVO-4 on the remotes you want to program.

5. The Parking lights will flash (1) time for each remote paired. (This is only if the parking lights are offered through

the integration module or if connected via an output from the module)

6. The system will automatically exit the remote learning procedure after (5) seconds of inactivity or by turning the

ignition off. The parking lights will flash (2) times to confirm programming exit.

Note: The EVO-ALL must have the CrimeStopper RF kit enabled under the Supported RF kits menu.

Note: Programming of the Data Module to the vehicle must be completed FIRST!

The system can learn up to 4 different transmitter codes.

There are 3 methods of programming remotes depending on the type of Data Module used to operate your vehicle.

TRANSMITTER PROGRAMMING

1. Press and hold the programming button on the EVO-ALL.

2. Insert the 4-pin Data-Link connector that comes with the EVO-ALL into the open 4-pin power on the power

adaptor next to the 2-pin power/ground harness.

Fortin EVO-ALL Programming (cont’d):

3. After the Blue and Red LED’s turn on simultaneously, release the programming button.

4. Press and hold the programming button on the EVO-ALL for (5) seconds. The Blue and Red LED’s will turn OFF

and back ON after (5) seconds. After the LED’s turn back ON release the programming button.

5. Turn the ignition ON. The yellow LED will turn ON.

6. Press the Start button on the REVO-1 or the Lock button on the REVO-4, you may have to hold the button for up

to 3 seconds. The Blue and Red LED’s will flash (1) time to confirm that the remote has coded. Repeat this

step for each remote you want coded. You can have up to (4) remotes at a time.

7. Turn the ignition off to exit remote programming.

TRANSMITTER PROGRAMMING

Fortin EVO-ONE Programming:

Note: Before you save your settings for programming of the EVO-ONE, ensure that you have Fortin 2 checked on

the remote starter options menu. Then save, disconnect and program the EVO-ONE to the vehicle.

1.Using the antenna cable that comes with the REVO kit, plug 1 end into the antenna and the other into the RF port

of the EVO-ONE. The RF port is the Blue 4-pin port next to the White port on the EVO-ONE. You will not need to

connect the power adaptor that comes with the REVO kit. NOTE: There are (2) Blue ports next to each other. Be

sure to use the Blue port furthest from the programming button.

TRANSMITTER PROGRAMMING

Fortin EVO-ONE Programming (cont’d):

2. Turn the Ignition to the ON position, do not start the vehicle. Press and hold the programming button until the

Red LED flashes in the opening where the yellow wires come out. None of the LED’s on top of the module

should be flashing.

3. Release the programming button.

4. Press and release the programming button (5) times.

5. Press and release the brake pedal once.

6. Press the Start button on the REVO-1 or the Lock button on the REVO-4, you may have to hold the button for up

to 3 seconds. The Red LED will flash (1) time to confirm that the remote has codded. Repeat this

step for each remote you want coded. You can have up to (4) remotes at a time.

7. Turn OFF the ignition to exit programming.

2 VEHICLE OPERATION

A single Remote Control can control two different vehicles.

To set up the 2-Vehicle operation you must first program your remotes to Vehicle #2. Follow the “Transmitter

Programming” steps (Pg. 6 - 9) at the second vehicle and learn YOUR remote, along with vehicle #2’s existing

remotes.

REVO-4 Series

VEH

VEH 1 = Blue LED

VEH 2 = Red LED

To change from Vehicle 1 to Vehicle 2, press the VEH button on the remote for about 2 seconds. The LED on the

remote will change from Blue to Red. The VEH button can be used the keep the remote control from accidentally

operating your vehicle.

POWER ADAPTOR WIRING

NOTE: The power connections are only needed for the EVO-ALL and ADS-ALCA integration modules. The

EVO-ONE will not require these connections. If you are using a T-Harness with the EVO-ONE or ADS modules

then you will NOT need to connect the power and ground connections. If you are NOT using a T-Harness, then you

WILL need to connect the power and ground wires. These wires will supply the power to the module as well as the

REVO antenna.

Connect the Red wire from the 2-pin power adaptor to a 12V constant source.

Connect the Black wire from the 2-pin power adaptor to a paint free, solid metal surface using a crimped on ring

terminal and self-tapping screw. For best results, use a nutsert and bolt.

Otros manuales para REVO-1 Series

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Arranque remoto de CrimeStopper

CrimeStopper

CrimeStopper ezee Start EZ-777 VII Manual de usuario

CrimeStopper

CrimeStopper COOL START RS-901 Manual de usuario

CrimeStopper

CrimeStopper Cool Start RS-7 Manual de usuario

CrimeStopper

CrimeStopper Cool Start RS-3 Manual de usuario

CrimeStopper

CrimeStopper EZEE START EZ-10 Manual de usuario

CrimeStopper

CrimeStopper PS01-G5 Manual de usuario

CrimeStopper

CrimeStopper RS-901.II Manual de usuario

CrimeStopper

CrimeStopper CS-2016DPII-FM Informer II Manual de usuario

CrimeStopper

CrimeStopper EZEE Start EZ-3 Manual de usuario

CrimeStopper

CrimeStopper CS-845RKE Series II Manual

CrimeStopper

CrimeStopper RS900/RS901 Manual de usuario

CrimeStopper

CrimeStopper RS800ER Manual de usuario

CrimeStopper

CrimeStopper EZ-31DP/33DP/34DP Manual de usuario

CrimeStopper

CrimeStopper SP-400 Manual de usuario

CrimeStopper

CrimeStopper RS-901.III Manual de usuario

CrimeStopper

CrimeStopper RS700 IIIER Manual de usuario

CrimeStopper

CrimeStopper COOL START RS-900 Manual de usuario

CrimeStopper

CrimeStopper EZEE Start EZ-1 Manual de usuario

CrimeStopper

CrimeStopper RS700 IIIER Manual de usuario

CrimeStopper

CrimeStopper LC-1 Manual de usuario

CrimeStopper

CrimeStopper Cool Start RS-1405DP Manual de usuario

CrimeStopper

CrimeStopper EZ-45DP/55DP Manual de usuario

CrimeStopper

CrimeStopper Ezee Start EZ-90 Manual de usuario

CrimeStopper

CrimeStopper SP-500 Manual de usuario

Manuales populares de Arranque remoto de otras marcas

AstroStart

AstroStart 803U Manual de usuario

Durite

Durite 0-649-20 Manual

EINHELL

EINHELL BT-PS 1000 Manual

Linear

Linear ACCESS AK-21 Especificaciones técnicas

Soundstream

Soundstream TARANTULA RS.2 Manual de usuario

Jaycar Electronics

Jaycar Electronics MB3752 Manual de usuario

Ultra Start

Ultra Start 72 Series Manual de usuario

ADS

ADS FLASHLOGIC FLRSVW1 Manual de usuario

Selecta

Selecta JS012 Manual de usuario

Black Widow Security

Black Widow Security BW RAS 400 Manual de usuario

Vector

Vector Power City DK080706 Suplemento

Code Alarm

Code Alarm CA-535 Manual de usuario

Ozito

Ozito OJS-800 Manual de usuario

Profi-Partner

Profi-Partner 46387 Manual de usuario

EZ STARTER

EZ STARTER EZ-45 Manual de usuario

Viper

Viper 4204 Manual de usuario

Essex Electronics

Essex Electronics KE-1701 Manual de usuario

EINHELL

EINHELL EGS 3600 Manual