Code Alarm SRT 5500 Manual de usuario

IMPORTANT NOTE: TheoperationoftheSecurityandConvenienceSystem asdescribedinthis

manualisapplicabletomostvehicles.However, due to theconfigurationof some vehicles, some

functionsAND/ORSAFETYPRECAUTIONS may not apply. Please see your installingdealerformore

information.

Owner's Manual

SRT 5500

Remote Vehicle Control System

Deluxe Vehicle Keyless Entry and

Remote Start System with 900Mhz

Remote Control

Table of Contents

Using Your Remote Control ................................................................................................................ 3

Lockingthesystem

Unlockingsystem

Disabling/Enabling confirmation chirps

Twostage door unlock*

Activatingthe trunk releasefeature*

Using Your Remote Control, continued....................................................................................... 4

Turningonthe vehicle’s headlights*

Activatingoptional AUX 1*

Activatingoptional AUX 2*

Activatingoptional AUX 3*

Activatingoptional AUX 4*

Using the progressive car finder feature

Usingthepersonal protection alarm

Using Your Remote Vehicle Starter ............................................................................................... 5

Remotestarting your vehicle

Enteringyourvehicle while it is running via remote vehicle start

Usingthesafety(red handled) control switch

Preheating or Precooling the vehicle’s interior

Usingthe “quick-stop” feature

Using Your Remote Vehicle Starter, continued ........................................................................... 6

Operatingthe2/4hour start up timer mode

Operatingthe temperature startmode

Using Your Remote Vehicle Starter, continued ........................................................................... 7

Operatingthe daily start timer

Remotestartsafetyfeatures

Usingvalet mode

Usingthe optional Turbo Timer feature*

Quick Reference Button Operation Guide.................................................................................... 8

Replacingremotecontrolbatteries

Emergencyoverride procedure

* Mayrequire additional installation labor, components and installation cost

Using Your Remote Control

Locking the System

Tolockthesystem, press the LOCK button. The parking lightswill flash 2 times and the horn willsound2times

indicatingthe system has lockedthedoors(if equipped and connected) andactivatedthe starter disable feature.

Thestatusindicator (blue warning light on the dash) will blink steadily, once per second. To lock the system

silently, press and hold the LOCK button for 1second. The parkinglights will flash 2 times, indicating the system

haslocked the doors (if equipped andconnected)andactivated the starter disable feature. Thestatusindicator

(bluewarninglightonthedash)willblinksteadily,oncepersecond.

Unlocking the System

Tounlockthe system press the UNLOCK button. The parkinglightswill flash 1 time and the hornwill sound 1 time

indicatingthe system has unlockedthedoors (if equipped andconnected)anddeactivated the starter disable

feature. Todisarmthe system silently, press and hold the UNLOCK buttonfor 1 second. The parkinglightswill

flash1 time, indicating the systemhasunlockedthe doors (if equipped andconnected)anddeactivated the starter

disablefeature.

Disabling/Enabling Confirmation Chirps

1. Turn the ignition key ON then OFF.

2. Within10 seconds pushandrelease the valet/override button3times.

3. Thesystemwillsound2timestodisable confirmation chirps or 1 time to enable confirmation

chirps.

Two Stage Door Unlock (Optional)

Ifthis feature is enabled on your system, pressing theUNLOCKbuttonone time on the remote control will unlock

onlythe driver’s door. Press UNLOCK again to unlock theremaining doors.

Activating the Trunk Release Feature (Optional)

Ifthisfeatureisenabledonyoursystem,pressingandholdingtheTRUNKbutton on the remote control for 2

secondswill open the vehicle’s trunk or hatch.

*Throughout this manual, ‘press’ refers to pressing for less than 1 second; ‘press and hold’ refers to pressing for

morethan2seconds.

Using Your Remote Control, continued

Turning on the Vehicle’s Headlights (Optional)

Ifthis feature is enabled on your system, pressing and holding the LOCK button on the remote control for 3

secondswillturnonthevehicle’sheadlightsfor30seconds.

Activating Optional AUX 1 (Optional)

Ifthis feature is enabledonyour system, press and releasetheOPT button on the remotecontrolto activate an

optionalfeature. This feature can be programmed for a widerangeoffunctions like power window or sunroof

automation,please consult yourinstallingdealer to determinefunctionalityof your system.

Activating Optional AUX 2 (Optional)

Ifthis feature is enabled on your system, pressing and holding the KEY buttonontheremotecontrolfor 2 seconds

willactivate an optional feature. Thisfeaturecanbe programmed for a wide rangeoffunctions like power window

orsunroof automation, please consultyourinstalling dealer to determinefunctionalityof your system.

Activating Optional AUX 3 (Optional)

Ifthis feature is enabled onyoursystem, pressing and holding theLOCKbuttonand the Trunk button ontheremote

controlsimultaneously for 2 seconds will activate anoptionalfeature.This feature can be programmed for awide

rangeof functions like power windoworsunroofautomation, please consult your installing dealertodetermine

functionalityofyour system.

Activating Optional AUX 4 (Optional)

Ifthis feature is enabled on your system, pressing and holding the UNLOCK button and the TRUNK button onthe

remotecontrol simultaneously for 2 seconds willactivateanoptional feature. This feature can beprogrammedfor

awide range of functions like power window orsunroofautomation,please consult your installing dealer to

determinefunctionalityofyour system.

Using the Progressive Car Finder Feature

Pressthe LOCK button and the UNLOCK button ontheremotecontrol to locate your vehicle. The system will

sound5 times at low volumeincreasinginvolume each of 3 timesthebuttonis pressed.

Using the Personal Protection Alarm (Panic)

Pressand hold the LOCKbuttonandthe UNLOCK button on theremotecontrol for 2 seconds toactivatethe

personalprotection alarm. The system will sound for 30 seconds. Pressing any button on the remote control will

turnthe personal protection alarm off.

Using Your Remote Vehicle Starter

Remote Starting Your Vehicle

Toactivate the remote vehiclestartfunction,pressand release the KEY button ontheremote control 2 times within

2seconds. The system will sound, the parking lights will flash 1 time and the system will check the vehicle to

ensureit is safe to start, if all safety parameters are correct, the vehiclewill start within 5 seconds (diesel

vehicles will take longer). The vehicle’s parking lights will turn on (or flash depending on system settings) as a

visualindication that the vehicle has started and is running. Press andreleasetheKEYbutton on the remote

control2 times within 2 seconds again to turn the vehicle off.

Ifyour vehicle stalls or does not start, the system will pause 5 seconds, then try 3 more times to start thevehicle(a

totalof 4 attempts). The systemwillpause 5 seconds between eachstartattempt. If the vehicle doesnotstart

afterthe 4th attempt, thesystemwill abort the remotevehiclestart process.

Entering the Vehicle while it is running via Remote Vehicle Start

1. Unlockthevehicle’sdoors.

2. Enter the vehicle. DO NOT PRESS THE BRAKE PEDAL!

3. Insertthe key into the ignition switch and turn tothe ON or RUN position.

4. Press the brake pedal. The remote vehicle starterwill disengage and the vehicle will operate normally.

Using the Safety (Red Handled) Control Switch

Thesafety (red handled) control switch allows you to temporarily disable the remote vehicle starter feature,thisis

especiallyhelpfulwhen having yourvehicleserviced or valetparked. Todisablethe remote start,movethesafety

(redhandled)control switch to the OFF position.

Preheating or Precooling the Vehicle’s interior

Beforeexiting the vehicle, set the temperaturecontrolstothe desired setting and operation. After the system

startsthevehicle, the heater or air conditioning will activate and heat or cool the vehicle’sinteriortoyour setting.

Using the “Quick-stop” Feature

Ifyou want to make ashortstopand keep your vehicle running(tokeepthe interior warm or cool),thequick-stop

featureallows youto dothiswhile keepingyourvehicle secureand your keyswith you.

To engage quick stop:

1. Stopthe vehicle and place the transmission in PARK.

2. Withyour foot offthebrake pedal, press andreleasethe KEY button ontheremote control 2

times within 2 seconds. The parking lights will turn on indicating the vehicle is now running

via remote vehicle start.

3. Removethe keys fromtheignition and exitthevehicle. Press the LOCKbuttonon the remote

control to lock the vehicle’s doors if desired.

Note: Donot leave children or animals unattended in the vehicle when using the quick-stop feature.

Using Your Remote Vehicle Starter, continued

Operating the 2 / 4 Hour Start Up Timer Mode

Thesystem has the ability to start the vehicle every 2 or 4 hours over a 48 hour period. This feature is especially

usefulin cold climates where the only means to keep the engine and engine fluids warm is to periodicallystartthe

engine.

WARNING!

Becertainthat the vehicle is outdoors before using this or any remote starting device. Arunningengineproduces

dangerouscarbon monoxide fumes which can be harmful or fatal if prolonged exposure occurs. DO NOT remote

start the vehicle if it is garaged.

Selecting between 2 and 4 hour start up: (default 4 hour)

1. Beginwith the safety (red handled) control switch in the ON position.

2. Turn the ignition switch ON then OFF.

3. Within 10 seconds move the safety (red handled) control switch OFF,ON, OFF, ON (2 switch

cycles) to select a 2 hour start timer. After 10 seconds the parking lights

willflashand the system will sound 2 times indicating that the 2 hour starttimeris selected.

3a. Within10 seconds move the safety (red handled) control switch OFF,ON,OFF, ON,

OFF, ON, OFF, ON (4 switch cycles) to select a 4 hour start timer. After 10 seconds the

parkinglights will flash and the system will sound 4 times indicating that the 4 hourstart

timeris selected.

To begin the 2 / 4 hour start up timer mode:

1. Turn the ignition key ON then OFF.

2. Within10 seconds press the KEY button on the remote control four (4) times.

Theparking lights will flash and thesystem will sound 4 times indicatingthe 2 / 4 hour start

uptimer mode has been activated. The vehiclewillstartevery 2 or 4 hours and run

forthepresettimelimit(5,10, 15 or 20 minutes) and then shutdown. This will continue

for48 hours unless the 2 / 4hour start up timer is cancelled.

To begin the 2 / 4 hour start up timer mode from the remote control:

1. Activatethe remote vehicle start feature usingtheremotecontrol.

2. Shutdownthe remote vehicle starter using the remotecontrol.

3. Within10 seconds press KEY button on the remotecontrol4times.

Theparking lights will flash and thesystem will sound 4 times indicatingthe 2 / 4 hour start

uptimer mode has been activated. The vehicle will start every 2 or4hoursandrun for the preset

timelimit(5,10,15or20minutes) and then shutdown. This will continue for 48 hours unless the

2 / 4 hour start up timer is cancelled.

To cancel the 2 / 4 hour start up timer mode:

1. Startthevehicleusingthe ignition key, then press thebrakepedal.

2. Activatethe remote vehicle start feature usingtheremotecontrol.

Operating the Temperature Start Mode

Thesystemhastheabilitytostartthe vehicle when the temperature reaches 0 degrees. To toggle this feature ON/

OFFusingthe remote control press the UNLOCK and TRUNK buttons simultaneously for1second.

Note: Thisfeature must be turned ON in options programming. Check with your installing dealer to insure this

featureis set to the ON position.

Using Your Remote Vehicle Starter, continued

Operating the Daily Start Timer

Thesystem has the ability to start your vehicle based on a 24-hour countdown timer. This feature requiresatwo-

partactivationsequence.Fromtheremote,pressingboththeTRUNK&LOCKbuttonstogetherwillactivatethe

24hour countdowntimer. Next, Whenyouare finished operating thevehiclefor the day, perform thefollowing

stepstocompletethisprocess.

1. Turn theignition ON/OFF (vehicle must be disarmed).

2. Within10 seconds, while pressing the brake, press and release the TRUNK button twice.

3. The vehicle will flash the parking lights 2 times.

Remote Start Safety Features

Forsafety and security reasons, the systemwillshutdownor prevent the remote vehicle starter fromactivatingif

anyof the following occur:

1. Thevehicle’s hood isopen.

2. Thebrake pedal is pressed priortoturning the ignition key to the ON position.

3. The enginereaches 3 times its normal idle speed.

4. Thesafety (red handled) control switch is moved totheOFFposition.

Using Valet Mode

To engage valet mode:

1. Turnthe ignition key to the ON position.

2. Pressand holdtheemergency override button.

3. Theblue dashboard mounted LED will light solid indicating that the system is in valet mode.

Whenvalet mode is activated the dash mounted status LED will light solid, and all security functionswillbe

disabled.

To disengage valet mode:

1. Turnthe ignition key to the ON position.

2. Pressand release theemergencyoverridebutton.

3. Theblue dashboardmountedLED will turnoffindicating that thesystemhas exited valetmode.

Whenthe valet modehasbeen deactivated the dashmountedstatus LED willturnoff and all securityfunctionswill

beenabledthenexttimethe systemis armed.

Using the optional Turbo Timer Feature

To engage the turbo timer feature:

1. Withthe vehicle running viatheignition key, and yourfootoffof the brake pedal.

2. Engagethevehicle’sparking brake.

3. Thevehicle’sparkinglightswillturnontoverifytheturbotimerfeaturehasbeenactivated.

4. Turn the ignition key OFF, the vehicle will continue to run for an additional 5 minutes.

To disengage the turbo timer feature:

1. Pressthe vehicle’s brake pedal.

2. Turnthesafety(redhandled) control switch to the OFF position.

Quick Reference Button Operation Guide.

Operation Function Lock Unlock Trunk KEY

OPT F Operation Method

Lock X Press and Release

Unlock X Press and Release

Headlight X Press and Hold for 3 seconds

Trunk X Press and Hold for 2 seconds

Car Finder X X Press and Release

Panic X X Press and Hold for 2 seconds

Remote Start X Press two times in 2 seconds

Temp Start X X Press and Release

Daily Start X X Press and Release

AUX1 X Press and Release

AUX2 X Press and Hold for 2 seconds

AUX3 X X Press and Hold for 2 seconds

AUX4 X X Press and Hold for 2 seconds

Check Status X X X Press both together for 1 second

Check Temp X X Press both together for 1 second

Battery Saver X X Press and Release, When System is Disarmed

Vibrate X X Press and Release

2/4 hour start X Press 4 times after remote start shut down

Shock Bypass X Press and release 2, 3, or 4 times

Parking Meter Timer X X Press and release 1, 2, 3, 4, 5 or 6 times

Alarm clock X X Press and Release

Fahrenheit / Celsius X X X Press and Release

Replacing Remote Control Batteries

1-Way 5 Button Remote Control:

Thetwo3 volt lithium batteries (model CR2032 or Code Alarm part#6BA) inside each remote control should last

approximately1 yearundernormal use. When thebatteries become weakyouwill noticetheremote control range

(thedistance from the vehicle the remote control will work) deteriorate and the small LED on the remote control will

dim. Toreplacetheremote control batteries:

1. Usinga small (#1) philips screwdriver, remove the 2 screwsonthebackoftheremote control.

2. Gentlyunsnap thehalvesof theremote controlapart.

3. Slidethe lithium batteries out of the circuit board, observing the +/- symbols on the batteries

andreplace with new lithium 3 volt batteries (model CR2032 or Code Alarm part # 6BA)

4. Gentlysnap the halves of the remote controlbacktogetherandreinstall the philips screws

onthe backofthe remote control.

5. Testoperation of theremotecontrol.

Emergency Override Procedure

If your transmitter is lostordisabled, it will be necessary use the emergency override button to turn the starter

disablefeature off.

1. Enterthevehicle.

2. TurntheignitionkeytotheONposition.

3. Pressandreleasetheemergencyoverridebutton.

Code Systems, Inc. Limited Lifetime Warranty

CodeSystemsInc.(“CODE”)warrants to the ORIGINAL PURCHASER of this CODE vehicle security

product (the “Product”), purchased from an authorized CODE dealer, that (except as provided below) should this

Productundernormal useandconditions,beproven defectiveinmaterialorworkmanship DURINGTHE LIFETIMEOF

THE VEHICLE INWHICH IT WAS ORIGINALLYINSTALLED, such defect(s) willbe repairedor replaced (atCODE’s

option)without charge for parts directly related to repairs of thedefect(s).

Switches,indicatorlights,and transmitter cases are similarly warranted to the original purchaser for a

periodof one (1) year from the date of purchaseoftheProduct.

CODEaccessories,soldseparately,arecoveredbytheapplicablewarrantyaccompanyingtheaccessory.

Thiswarranty is non-transferable, non-assignableandis voided when: (1)theProduct is removed from

thevehiclein which it was originally installed; or (2) the vehicle in whichthe Product was originally installed is trans-

ferredto anotherparty.

Thiswarrantydoesnotapplytoanyproductdamagedbyaccident,physicalorelectricalabuse,improper

installation,alteration,orusecontrarytoits intended function, fire, flood, or other natural acts.

Inorder forthe Producttobe repairedor replacedunderthe termsof thiswarranty,the defectiveProduct

mustbe returned to an authorized CODE dealer and accompanied by a copy of the retail sales receipt. Thedate of

purchaseandyear,makeandmodel ofthevehicleinwhichtheProductwas originallyinstalledmustbeclearly indicated

onthe sales receipt.

Thiswarranty isexclusive andCODE MAKESNO OTHERWARRANTIESEXPRESSED ORIMPLIED.

ANY IMPLIED WARRANTIES, INCLUDINGANY IMPLIED WARRANTY OF MERCHANTABILITYANDFITNESS

FORAPARTICULAR PURPOSE, SHALLBE LIMITED TO THE DURATION OF THIS WRITTEN WARRANTY. IN

NO CASE SHALLCODE BE LIABLE FORANYCONSEQUENTIAL OR INCIDENTAL DAMAGES FOR BREACH

OF THIS ORANY OTHER WARRANTY, EXPRESS OR IMPLIED, WHATSOEVER.

CODE does not warrant that the Product cannot be compromised or circumvented. THE EXTENT OF CODE’S

LIABILITY UNDER THIS WARRANTY IS LIMITED TO THE REPAIR OR REPLACEMENT PROVIDEDABOVE

AND, IN NO EVENT SHALL CODE’S LIABILITY EXCEED THE PURCHASE PRICE PAID BY THE ORIGINAL

PURCHASER OF THE PRODUCTWITHOUT INSTALLATION LABOR.

Somestatesdo notallowtheexclusionor limitationof incidentalorconsequentialdamages,so theabove

limitationmay not applyto you. This warrantygivesyou specific legalrightsand you mayalsohave other rightswhich

varyfrom stateto state

FCC COMPLIANCE

This device complies with Part 15 of the FCC rules and with RSS-210 of Industry

Canada. Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and

2. This device must accept any interference received, including any interference that

may cause undesired operation.

Warning!

Changes or modifications not expressly approved by the party responsible for

compliance could void the user’s authority to operate the equipment.

Code Systems, Inc.

Customer Service 1-800-421-3209

WWW.CODE-ALARM.COM

Tabla de contenidos

Otros manuales de Alarma de coche de Code Alarm

Code Alarm

Code Alarm Power Elite PC 4100 Manual de usuario

Code Alarm

Code Alarm 420A Manual de usuario

Code Alarm

Code Alarm CATX630 Instrucciones de funcionamiento

Code Alarm

Code Alarm Ca 1053 Manual de usuario

Code Alarm

Code Alarm CA 110 Manual de usuario

Code Alarm

Code Alarm UTXPR Manual del propietario

Code Alarm

Code Alarm CATX130 Instrucciones de funcionamiento

Code Alarm

Code Alarm CATX520 Instrucciones de funcionamiento

Code Alarm

Code Alarm CA-230 Manual de usuario

Code Alarm

Code Alarm CA 510 Manual de usuario

Code Alarm

Code Alarm CA 1550 Manual de usuario

Code Alarm

Code Alarm CSI-300 Manual de usuario

Code Alarm

Code Alarm CA611 Manual de usuario

Code Alarm

Code Alarm 2000 Manual de usuario

Code Alarm

Code Alarm TW-1 Manual de usuario

Code Alarm

Code Alarm ca 2051 Manual de usuario

Code Alarm

Code Alarm CATX2LCD Instrucciones de funcionamiento

Code Alarm

Code Alarm CA 6151 Manual de usuario

Code Alarm

Code Alarm CA-330 Manual de usuario

Code Alarm

Code Alarm SRT 1600 Manual de usuario

Code Alarm

Code Alarm Professional Series CA 1050 Manual de usuario

Code Alarm

Code Alarm Professional ca6153 Manual de usuario

Code Alarm

Code Alarm CA-125 Manual de usuario

Code Alarm

Code Alarm Procomp Manual de usuario

Manuales populares de Alarma de coche de otras marcas

Clifford

Clifford 3606X Manual de usuario

Ultra Start

Ultra Start 2500M SERIES Manual de usuario

Ultra Start

Ultra Start 650 Series Manual de usuario

Audiovox

Audiovox Prestige Platinum+ APS-511C Manual de usuario

Sparkrite

Sparkrite SRA8 Manual de usuario

Viper

Viper 4708V Manual de usuario

Federal Signal Corporation

Federal Signal Corporation Pathfinder Siren Series Manual

Falcon

Falcon Predator XL3 Guía del usuario

Audiovox

Audiovox Auto Security XR91 Instrucciones de funcionamiento

Clifford

Clifford Sabre II Manual de usuario

CrimeStopper

CrimeStopper CS-8717 Guía de inicio rápido

Ultra Start

Ultra Start 450 SERIES Manual de usuario

Scytek electronic

Scytek electronic Vectra X3 Manual de usuario

Excalibur

Excalibur AL-1860-EDPB Manual de usuario

Clifford

Clifford CYBER 2 Manual de usuario

Gemini

Gemini 7057 Manual de usuario

FlashLogic

FlashLogic FLRSBA PRESTIGE Manual de usuario

Magicar

Magicar FAI-440 Manual de usuario