Code Alarm CA-130 Manual de usuario

Owner's Manual

Remote Vehicle Control System

IMPORTANT NOTE: The operation of the Securityand Convenience System as described

in this manual is applicable to most vehicles. However, due to the configuration of some

vehicles, some functions AND/OR SAFETY PRECAUTIONS may not apply. Please see

your installing dealer for more information.

CA-130TM

Security and Convenience

System

CA 130 owners rev 7-04.pmd 7/28/2004, 3:34 PM1

2Table of Contents

Features and Benefits of the Code Alarm CA-130TM....................... 3

Using Your Remote Transmitter .............................................. 4

Arming the Security System

Pre-arm Mode

Disarming the Security System

Attempted Intrusion Identification

Disabling the IT-sTM Interior Theft Sensor ............................... 5

Two-Stage Door Unlock

Activating the Trunk Release Feature

Aux 1

Turning on the Vehicle Headlights/Aux 2

AUX 3

AUX 4

Using the Car Finder Feature

Personal Protection Alarm (Panic)

Using Valet Mode ....................................................................... 6

Automatic Convenience Options ............................................ 6

When Your Security System is Triggered ............................... 7

The Interior Status Indicator .................................................... 7

System Maintenance ................................................................... 7

Changing the Remote Control Battery

System Maintenance ................................................................... 8

Adding Remote Controls to Your System

Deleting Lost or Stolen Remote Controls from Your System

Emergency Disarm Procedure ............................................ 9

E-code Coded Override procedure

Emergency Disarm Button Location................................... 9

Basic Troubleshooting................................................................ 10

Installer Programmed Options .................................................. 10

Personalized Transmitters Option ............................................ 11

Your Code-Systems, Inc. Limited Lifetime Warranty .............. 12

Code Systems Theft Protection Plan........................................ 13

CA 130 owners rev 7-04.pmd 7/28/2004, 3:34 PM2

Features and Benefits of the Code Alarm CA-130TM

Two Easy-to-Use Weather-Resistant Remote Controls

The remote controls included with the Code Alarm CA-130TM utilize

durable, moisture resistant cases and sealed rubber buttons for

reliability and long life. Rolling code technology prevents the

transmitter signals from being duplicated. The button functions are

clearly labeled to make the Code Alarm CA-130TM simple to operate.

All Entrances Protected

Opening any door or entrance protected by the security system

triggers the alarm’s 125db siren (or vehicle horn) and flashes the

vehicle parking lights.

Starter Disable

The Code Alarm CA-130TM protects your vehicle from theft by

disabling the starter when the system is armed.

IT-sTM Interior Theft Sensor

This patented sensor uses infra-red technology to reliably detect

vehicle impact associated with attempted intrusion. The IT-s sensor

guards against vehicle body damage, and theft of the vehicle’s

equipment (such as airbags) and personal belongings.

Remote Keyless Entry

The Code Alarm CA-130TM conveniently locks and unlocks the

vehicle’s doors and opens the trunk or hatch (if equipped and

connected) by remote control.*

Personal Protection Features

Remote Panic Alarm, Headlight Control, Illuminated Entry,

and Car Finder are among an array of features that enhance

personal safety. **May require additional componets and/or labor

Interior Status Indicator

The bright-blue warning light is an effective visual deterrent to a

would-be thief.

PowerRangeTM Antenna

This long-range antenna allows you to operate the Code Alarm CA-

130TM from distances of up to 1/8mile.

E-Code Coded Override System

If this feature is enabled, it will allow you to enter a personal 4-digit

code that only you will know. This will be used for overriding the

system in the case of an emergency or a lost transmitter.

*If vehicle is equipped with power door locks and they are connected to the alarm system by your installer.

CA 130 owners rev 7-04.pmd 7/28/2004, 3:34 PM3

* Throughoutthismanual, ‘press’ refers to pressing

forlessthan 1 second; ‘press and hold’refersto

pressingformore than 1 second.

** ’Siren’ also refers to the vehicle horn if it is used as the alarm sounding device.*

†Ifyouhavechosen the Silent Arming Option, the siren willnotsoundwhen arming or disarming until the

appropriatebuttonis pressed a secondtime.

Arming the Security System

To arm the system, exit the vehicle, close all doors, then press* the

LOCK button. The siren** will “chirp” twice†and the parking lights will

flash twice, indicating the system is armed. The doors will also lock at

this time (if equipped and connected). The status indicator (blue

warning light on the dash) will blink steadily, once per second.

Pre-arm Mode

If the siren chirps and the parking lights flash only once, this indicates

that the vehicle courtesy light is on, or that an entrance is not closed

securely. Check to see that doors, hood, and trunk are properly

closed. Once all entrances are secured (and the courtesy light is off),

the system will chirp / flash again. The system is now fully armed.

(If the entrance is not secured within 4 minutes, the system will arm

and ignore the unsecured entrance until it is closed.)

Disarming the Security System

To disarm the system, press the UNLOCK button. The siren will chirp

and the parking lights will flash once, and the doors will unlock. The

courtesy light will turn on for 1 minute, or until the vehicle is started.

Attempted Intrusion Identification

If the siren chirps four times when disarming, this indicates that the

system was triggered in your absence. The status indicator will also

flash rapidly. Perform the following operation to determine the protected

zone that triggered the system:

After disarming, press the

emergency override button.

The siren will chirp to indicate

the cause of the alarm trigger:

1 chirp IT-s Interior Theft Sensor

2 chirps Door

3 chirps Hood

4 chirps Trunk/Optional Sensors

5 chirps Ignition was turned on

Using Your Remote Transmitter

LOCK Button

FIND/PANIC Button

Press for Car Finder

Press and Hold for

Panic Alarm

UNLOCK Button

Press to Disarm Security

System and Unlock

Doors

Press Twice for Two-

Stage Door Unlock*

Pressand HoldtoOpen

Trunk

LIGHTSButton

Press to Turn

Headlights ON

Press LIGHTS and

FIND/PANIC

Together to

Activate Aux 4

Press to Arm Security

System and Lock

Doors

Press and Hold to

Activate Aux 1

Press LOCK and

UNLOCK Together

to Activate Aux 3

CA 130 owners rev 7-04.pmd 7/28/2004, 3:34 PM4

Using Your Remote Transmitter (cont.)

Disabling the IT-s Interior Theft Sensor

It may be necessary at times to disable the IT-s Interior Theft Sensor,

especially when parking in areas (like parking garages) where

extreme vibration may cause false alarms. Press the LOCK button

and then press the FIND/PANIC button within two seconds of

pressing LOCK to disable the interior theft sensor.The siren will chirp

two times to indicate that the sensor is disabled. The sensor will

become enabled again the next time the system is armed normally.

Two-Stage Door Unlock

If this feature is enabled on your system, pressing UNLOCK one time

will unlock only the driver’s door. Press UNLOCK again within 1

minute to unlock all doors.

Activating the Trunk Release Feature

Press and hold UNLOCK to open the vehicle trunk or hatch (if

equipped and connected). If this button is used to operate another

accessory, the accessory will stay active for as long as the button is

held.

UsingAUX 1

If this feature is enabled on your system, press and hold LOCK to

activate Auux 1.

Turning on the Vehicle Headlights (Aux 2)

Press the LIGHTS button to turn on the vehicle headlights. The lights

will stay on for 20 seconds, or until LIGHTS is pressed again.

UsingAUX 3

If this feature is enabled on your system, pressing LOCK and

UNLOCK simultaneously will activate Auxilliary 3.

UsingAUX 4

If this feature is enabled on your system, pressing FIND/PANIC and

OPTION simultaneously will activate auxillary 4.

Using the Progressive Car Finder Feature

Press FIND/PANIC on the remote control to locate your vehicle. The

vehicle horn will emit five short chirps at low volume, increasing in

volume each of three times the button is pressed.

Personal Protection Alarm (Panic)

Press and hold the FIND/PANIC button to activate the vehicle siren

and parking lights for 30 seconds. (If the vehicle horn is connected,

the horn will “pulse” for 30 seconds.) Press any remote control button

to turn off the Panic alarm.

CA 130 owners rev 7-04.pmd 7/28/2004, 3:34 PM5

Using Valet Mode

If the Passive Arming feature is enabled on your system, Valet mode

temporarily prevents the alarm system from arming automatically.

This is useful when fueling or servicing your vehicle.

To enter Valet Mode:

With the vehicle ignition key in the ON position, press the LOCK and

UNLOCK buttons simultaneously. The blue dashboard warning light

(status indicator) will turn on for one second, then turn off. This

indicates that the system is in Valet mode. Once the ignition is turned

off, the status indicator will emit a quick double-flash pattern.

Note: In Valet mode, all keyless entry, convenience features operate

normally.

To exit Valet Mode:

With the vehicle ignition key in the ON position, press the LOCK and

UNLOCK buttons simultaneously. The blue dashboard warning light

(status indicator) will turn on for one second, then turn off. This

indicates that the system has exited Valet mode.

Automatic Convenience Options

The Code Alarm CA-130TM performs a variety of automatic functions to

enhance security and comfort. Some of these features are

programmable at the time of installation. Please see your installer for

further details.

Illuminated Entry

When the alarm system is disarmed, the vehicle courtesy lights will turn

on for 1 minute, or until the vehicle is started or the system is re-armed.

Illuminated Exit

When removing the key from the ignition, the vehicle courtesy lights

will turn on for 1 minute, or until the system is armed.

Automatic Arming

The Code Alarm CA-130TM will arm automatically 1 minute after the

key is removed from the ignition. This feature can be temporarily

disabled by placing the system into Valet mode.

Ignition Lock

If all doors are closed and the vehicle is started with the key, the doors

will automatically lock.

Ignition Unlock

When turningthe ignition key off, the doors will automatically unlock.When

Using Your Remote Transmitter (cont.)

CA 130 owners rev 7-04.pmd 7/28/2004, 3:34 PM6

The Code Alarm CA-130TM will trigger if one of the following events

occurs while the system is armed:

• Any protected entrance is opened

• The vehicle ignition is turned on

• The vehicle is jolted hard enough to signal the impact sensor

Once the alarm is triggered, the siren (or horn) sounds and the

vehicle parking lights flash for 30 seconds. The system will then re-

arm, awaiting the next intrusion attempt. To stop the siren while

keeping the system armed and doors locked, press the LOCK button

while the system is triggered.

The Status Indicator is a high-intensity red light mounted in a visible

location on the vehicle dashboard. This red light gives a visual

indication of the alarm system’s state of operation. Note the chart

below:

If the Status Indicator is... ....then the Security System

Off is disarmed

Flashing Slowly is armed

Flashing Very Quickly was triggered in your absence

(see Attempted Intrusion ID - page 4)

Flashing Intermittently is in Valet mode

(2 flashes, off, 2 flashes)

On (not flashing) is in Pre-arm mode

System Maintenance

Changing the Remote Control Battery

The 12-volt alkaline battery (GP-23A) supplied in your remote control

should last approximately one year, depending on usage. When the

battery begins to weaken, you will notice a decrease in range, or the

distance from your vehicle that your remote transmitter will operate.

Follow the instructions below to change the remote transmitter battery.

1.Insert the edge of a coin into the slot at the side of the remote

control. Twist the coin to pry the remote control halves apart.

2.Remove the old batteries and replace with new ones.

Be sure to observe the (+) and (-) signs in the battery compartment.

3.Carefully snap the case halves back together, then test the

remote control.

When your Security System Is Triggered

CA 130 owners rev 7-04.pmd 7/28/2004, 3:34 PM7

8System Maintenance (cont.)

Adding Remote Controls to Your System

The Code Alarm CA-130TM has the ability to operate from up to eight

(8) remote controls. Follow these instructions to add a remote control to

your system.

1.Make sure the security system is disarmed and the ignition is off.

2.Open the driver’s door.

3.Turn vehicle ignition on.

4.Press and hold the emergency override button.

After 10 seconds, the siren or horn will sound three (3) times.

This indicates that the unit has entered the remote control

programming mode.

5.Release the emergency override button.

6.Press the LOCK button (button 1) on the remote control to be

programmed.

The siren or horn will sound once, indicating that the system

has “learned” that remote control.

7.Repeat step 6 for any additional remote controls.

8.Turn the vehicle ignition off to exit the programming mode. Test

all remote controls to ensure that they work properly.

Deleting Lost or Stolen Remote Controls fromYour System

If one of your remote controls is lost or stolen, follow these instructions

IMMEDIATELY to remove the control code from your system.

1. Have all remaining remote controls available.

2. Enter the control programming mode by following steps 1 - 5 of

Adding Remote Controls to Your System (page 8).

3a.If you have only one remaining remote control, press the

LOCK button on that remote control eight (8) times, pausing

at least 1 second between each press. Make sure that the

siren chirps each time you press the LOCK button.

3b.If you have two remaining remote controls, press theLOCK

button on each remote control four (4) times, pausing at

least 1 second between each press. Make sure that the siren

chirps each time you press the LOCK button.

3c.If you have three remaining remote controls, press the

LOCK button on the two remote controls three (3) times, then

press the LOCK button on the remaining remote control twice.

Pause at least 1 second in between each press. Make sure

that the siren chirps each time you press the LOCK button.

4. Turn the vehicle ignition off to exit the programming mode.

When you are finished, the lost or stolen remote control will no

longer operate your system.

CA 130 owners rev 7-04.pmd 7/28/2004, 3:34 PM8

Emergency Disarm Procedure

If your remote control is lost or fails to function, use this procedure to

disarm the Code Alarm CA-130TM and start your vehicle.

1.Use the keys to enter the vehicle.

The alarm will sound once the door is opened.

2.Insert the key into the ignition and turn to the ON position.

3.Locate and press the emergency override button.

The alarm will turn off and then you will be able to

start your vehicle.

If the E-code coded override feature is enabled on your system, use

this procedure to disarm the Code Alarm CA-130 and start your

vehicle.

1. Use the keys to enter the vehicle.

The alarm will sound once the door is opened.

2. Insert the key into the ignition and turn to the ON position

3. Press and release the emergency override button the

number of times that corresponds to the first digit of the

code and turn the ignition key off.

4. Turn the ignition key to the ON position.

5. Press and release the emergency override button the

number of times that corresponds to the second digit of

the code and turn the ignition key off.

6. Follow steps 4 and 5 for the remaining two digits of the

code. After the correct 4 digit code has been entered, the

system will disarm.

Contact your installing dealer to change or activate you personal E-

code.

Your Emergency Disarm Button is located:

Emergency Override Procedure

CA 130 owners rev 7-04.pmd 7/28/2004, 3:34 PM9

10 Basic Troubleshooting

This section outlines some of the basic issues you may experience

while becoming used to the Code Alarm CA-130TM. If you have a

problem that is not covered by this section, please consult your installer.

motpmyS melborP noituloS

seodlortnocetomeR krowton

yrettabdaedrokaeW

tonlortnocetomeR demmargorp

yrettabegnahC

etomermargorP )8egap(lortnoc

mratonlliwmetsyS

rehtororooD neposiecnartne

nosithgilysetruoC

telaVnisimetsyS edom

ecnartneesolC

ffoth

gilysetruocnruT

edomtelaVffonruT )6egap(

tratstonlliwmetsyS neposidooH

desserpsiekarB

doohesolC

ekarbesaeleR

Installer Programmed Options

Ignition On Door Lock ON OFF

Ignition Off Door Unlock ON OFF

Illuminated Entry/Exit ON OFF

Siren/Horn Chirps ON OFF

Passive Arming ON OFF

Pasive Door Locks ON OFF

AUX1 Output Duration_____________________

Light/AUX2 Output Duration_____________________

AUX3 Output Duration_____________________

AUX4 Output Duration_____________________

CA 130 owners rev 7-04.pmd 7/28/2004, 3:34 PM10

Otros manuales para CA-130

Tabla de contenidos

Otros manuales de Alarma de coche de Code Alarm

Code Alarm

Code Alarm 2000 Manual de usuario

Code Alarm

Code Alarm Professional 1000 Manual de usuario

Code Alarm

Code Alarm Power Elite PC 4100 Manual de usuario

Code Alarm

Code Alarm CA1355E Manual de usuario

Code Alarm

Code Alarm CA-125 Manual de usuario

Code Alarm

Code Alarm Elite CA6155e Manual de usuario

Code Alarm

Code Alarm ca6554 Manual de usuario

Code Alarm

Code Alarm PROFESSIONAL SERIES Manual de usuario

Code Alarm

Code Alarm CA-230 Manual de usuario

Code Alarm

Code Alarm caSEC Manual de instalación y funcionamiento

Code Alarm

Code Alarm CA 421 Manual de usuario

Code Alarm

Code Alarm CA 180 Manual de usuario

Code Alarm

Code Alarm F10 Manual de usuario

Code Alarm

Code Alarm PROFESSIONAL CA 1045 Manual de usuario

Code Alarm

Code Alarm ca 1151 Manual de usuario

Code Alarm

Code Alarm F20 Manual de usuario

Code Alarm

Code Alarm CA-500 Manual de usuario

Code Alarm

Code Alarm ca6355E Manual de usuario

Code Alarm

Code Alarm CA-330 Manual de usuario

Code Alarm

Code Alarm CA 680 Manual de usuario

Code Alarm

Code Alarm 2000 Manual de usuario

Code Alarm

Code Alarm CATX2LED Instrucciones de funcionamiento

Code Alarm

Code Alarm CATX130 Instrucciones de funcionamiento

Code Alarm

Code Alarm PROFESSIONAL SERIES CA 1551 Manual de usuario

Manuales populares de Alarma de coche de otras marcas

Clifford

Clifford 3606X Manual de usuario

Ultra Start

Ultra Start 2500M SERIES Manual de usuario

Ultra Start

Ultra Start 650 Series Manual de usuario

Audiovox

Audiovox Prestige Platinum+ APS-511C Manual de usuario

Sparkrite

Sparkrite SRA8 Manual de usuario

Viper

Viper 4708V Manual de usuario

Federal Signal Corporation

Federal Signal Corporation Pathfinder Siren Series Manual

Falcon

Falcon Predator XL3 Guía del usuario

Audiovox

Audiovox Auto Security XR91 Instrucciones de funcionamiento

Clifford

Clifford Sabre II Manual de usuario

CrimeStopper

CrimeStopper CS-8717 Guía de inicio rápido

Ultra Start

Ultra Start 450 SERIES Manual de usuario

Scytek electronic

Scytek electronic Vectra X3 Manual de usuario

Excalibur

Excalibur AL-1860-EDPB Manual de usuario

Clifford

Clifford CYBER 2 Manual de usuario

Gemini

Gemini 7057 Manual de usuario

FlashLogic

FlashLogic FLRSBA PRESTIGE Manual de usuario

Magicar

Magicar FAI-440 Manual de usuario