Code Alarm CATX120 Instrucciones de funcionamiento

Model CATX120

Programming Guide

The keychain transmitters included with the system have

been pre-programmed at the factory, with each button pre-

assigned to control a specific function of the system.

It is important to remember that during programming, each

individual step of the procedure must be executed within 15

seconds of the previous step.

When the 15 second time limit is allowed to expire, the

system will automatically terminate the programming mode.

This is indicated by a long chirp from the siren.

Additionally, the system will store codes from up to 4

different transmitters. If a 5th transmitter is programmed to

any receiver channel, then the first transmitterprogrammed

to that channel will be erased from the system’s memory.

To program new or additional transmitters, the alarm must

be disarmed and the valet switch must be in the OFF

position:

1. Enter the vehicle, and turn the ignition key to the ON

position.

2. Press and release the valet/programming/override

switch 3 times.

3. The dash LED will flash one time, and the sounding

device will beep one time, indication the system is ready to

accept programming for transmitter 1.

4. Press and hold the Arm Icon button until the sounding

device emits a long beep, indicating the signal has been

stored into memory.

5. If you have additional transmitters (up to 4) that need to

be programmed, repeat step 4 for each transmitter.

Changing the Remote Control Battery

The 12-volt alkaline battery supplied in your remote

transmitter should last approximately one year, depending on

usage. When the battery begins to weaken, you will notice a

decrease in range, or the distance from your vehicle that

your remote transmitter will operate. Follow the instructions

below to change the remote transmitter battery.

For Customer Service and Product information Call

1-800-421-3209

1. Insert the edge of a coin into the slot at the side of the

remote control. Twist the coin to pry the remote control

halves apart.

2. Remove the old battery and replace with a new one. Be

sure to observe the (+) and (-) signs in the battery

compartment.

3. Carefully snap the case halves back together, then test

the remote control.

Model CATX120

Programming Guide

Tabla de contenidos

Otros manuales de Alarma de coche de Code Alarm

Code Alarm

Code Alarm CA 521 Manual de usuario

Code Alarm

Code Alarm SRT 5500 Manual de usuario

Code Alarm

Code Alarm CA-130 Manual de usuario

Code Alarm

Code Alarm CA 680 Manual de usuario

Code Alarm

Code Alarm CA-135 Manual de usuario

Code Alarm

Code Alarm caSEC Manual de instalación y funcionamiento

Code Alarm

Code Alarm ELITE Series Manual de usuario

Code Alarm

Code Alarm CA-640 Manual de usuario

Code Alarm

Code Alarm CA 170 Manual de usuario

Code Alarm

Code Alarm CA-160 Manual de usuario

Code Alarm

Code Alarm CA 420 Manual de usuario

Code Alarm

Code Alarm CATX2LCD Instrucciones de funcionamiento

Code Alarm

Code Alarm CATX2LED Instrucciones de funcionamiento

Code Alarm

Code Alarm CA 420 Manual de usuario

Code Alarm

Code Alarm CA 420A Manual de usuario

Code Alarm

Code Alarm CA-330 Manual de usuario

Code Alarm

Code Alarm ca 1552 Professional Series Manual de usuario

Code Alarm

Code Alarm CA- 550 Manual de usuario

Code Alarm

Code Alarm CATX610 Instrucciones de funcionamiento

Code Alarm

Code Alarm PROFESSIONAL SERIES Manual de usuario

Code Alarm

Code Alarm CA1B5 Manual de usuario

Code Alarm

Code Alarm CSI-200 Manual de usuario

Code Alarm

Code Alarm Power Elite PC 4100 Manual de usuario

Code Alarm

Code Alarm ca 1552 Professional Series Manual de usuario

Manuales populares de Alarma de coche de otras marcas

Clifford

Clifford 3606X Manual de usuario

Ultra Start

Ultra Start 2500M SERIES Manual de usuario

Ultra Start

Ultra Start 650 Series Manual de usuario

Audiovox

Audiovox Prestige Platinum+ APS-511C Manual de usuario

Sparkrite

Sparkrite SRA8 Manual de usuario

Viper

Viper 4708V Manual de usuario

Federal Signal Corporation

Federal Signal Corporation Pathfinder Siren Series Manual

Falcon

Falcon Predator XL3 Guía del usuario

Audiovox

Audiovox Auto Security XR91 Instrucciones de funcionamiento

Clifford

Clifford Sabre II Manual de usuario

CrimeStopper

CrimeStopper CS-8717 Guía de inicio rápido

Ultra Start

Ultra Start 450 SERIES Manual de usuario

Scytek electronic

Scytek electronic Vectra X3 Manual de usuario

Excalibur

Excalibur AL-1860-EDPB Manual de usuario

Clifford

Clifford CYBER 2 Manual de usuario

Gemini

Gemini 7057 Manual de usuario

FlashLogic

FlashLogic FLRSBA PRESTIGE Manual de usuario

Magicar

Magicar FAI-440 Manual de usuario