Code Alarm ELITE Series Manual de usuario

ELITE

SERIES

Owner’s Guide

For Model:

ca1555E

IMPORTANT NOTE: The operation of the Security and Convenience System as described in this manual is

applicable to most vehicles. However, due to the conguration of some vehicles, some functions AND/OR

SAFETY PRECAUTIONS may not apply. Please see your installing dealer for more information.

Deluxe Vehicle Security and

Keyless Entry System with 2 Way Conrming

LCD Remote Control

2ca1555E Owners revA

Table of Contents

Using Your Remote Control.................................................................... 3

Arming the Security System .............................................................. 3

Passive Arming Bypass..................................................................... 3

Bypassing the Shock Sensor ............................................................ 3

Hidden Alarm Function...................................................................... 3

Disarming the Security System ......................................................... 3

Two Stage Door Unlock (optional)..................................................... 4

Activating Trunk Release (optional)................................................... 4

Activating AUX 1 (optional)................................................................ 4

Entering AUX Mode and Activating Additional AUX Outputs............. 4

Using the Progressive Car Finder Feature........................................ 5

Using the Personal Protection Alarm................................................. 5

Programmed Transmitter Notication................................................ 5

Valet Mode ........................................................................................ 5

User Selectable Notication Chirps................................................... 5

User Selectable LED ......................................................................... 6

Manually Overriding the Security System ......................................... 6

Carjack Mode .................................................................................... 6

Status LED, Light Flashes and Siren/Horn Indications ....................... 7

Additional 2-Way LCD Remote Control Functions............................... 8

LCD Remote Control ICON’s ................................................................ 10

Remote Control Buttons & Functions ................................................. 11

Replacing Remote Control Batteries................................................... 13

Programming Replacement Remote Controls.................................... 14

Warranty Information ............................................................................ 15

Arming the Security System

To arm the system, exit the vehicle, close all doors, then press the button. The

parking lights will ash 2 times, indicating the system is armed, has locked the doors

(if equipped and connected) and activated the starter disable feature. The LED status

indicator will blink steadily, once per second.

NOTE: The system is equipped with a feature called Silent Choice. If enabled, the

system requires a second press of the button to activate an audible arming

response from the vehicle.

Passive Arming Bypass

If passive arming is enabled on your system, while the system is disarmed, press

+ , the system will respond with 1 chirp and the LED will turn on. The security

system will remain in this temporally bypassed state for as long as you wish. To exit

passive bypass, press the or button and the system will return to normal status.

Bypassing The Shock Sensor

To arm the system and ignore the shock sensor press button, then within 5

seconds press + , the system will respond with 1 long chirp.

NOTE: The system will only change the shock sensor setting for one arm cycle and

will be defaulted back to normal operation the next time the system is armed.

Hidden Alarm Function

Press the button rst, within 3 seconds press the button to activate the hidden

alarm function. The security system will arm with “Hidden Alarm Function” in which the

siren / horn will be silenced if the system is triggered.

Disarming the Security System

To disarm the system press the button. The parking lights will ash 1 time,

indicating the system is disarmed and has unlocked the doors (if equipped and

connected).

NOTE: The system is equipped with a feature called Silent Choice. If enabled, the

system requires a second press of the button to activate an audible disarming

response from the vehicle. If your system is set up for 2 step unlock, a third press of

unlock will activate the audible response.

*Throughout this manual, ‘press’ refers to pressing for less than 1 second; ‘press and hold’ refers to pressing for more

than 2 seconds.

Using Your Remote Control

4ca1555E Owners revA

Two Stage Door Unlock (Optional)

If this feature is enabled on your system, pressing the button one time will unlock

only the driver’s door. Press again within three seconds to unlock the remaining

doors.

Activating the Trunk Release Feature (Optional)

If this feature is enabled on your system, pressing and holding the button for 3

seconds will open the vehicle’s trunk or hatch.

Activating the AUX 1 Output (Optional)

If this feature is enabled on your system, pressing the and buttons

simultaneously will activate an optional feature. This feature can be programmed for a

wide range of functions like power window or sunroof automation, please consult your

installing dealer to determine the functionality of your system.

Entering AUX Mode and Activating the Additional AUX 2 - 5 Outputs (Optional)

To access the additional AUX outputs, AUX 2, AUX 3, AUX 4, and AUX 5, you must

rst enter the transmitters AUX Mode. This will “shift” the functions of the transmitter

buttons from their standard operation to control of the AUX outputs.

AUX Mode - 4 button transmitter: Press and Hold and for 2

seconds, the transmitter LED will ash 1 time. AUX Mode will remain active

for 15 seconds. AUX Mode will exit after 15 seconds of inactivity or by

pressing and again for 2 seconds, the transmitter LED will ash 2

times to conrm exit.

AUX Mode - LCD 5 Button transmitter: Press and Hold for 2 seconds, the

transmitter LCD screen will display “AU”. AUX Mode will remain active

for 15 seconds. AUX Mode will exit after 15 seconds of inactivity or by

pressing again for 2 seconds.

Activating outputs while in AUX Mode:

AUX 2: Press and Hold for 3 seconds.

AUX 3: Press and Hold for 3 seconds.

AUX 4: Press and Hold for 3 seconds.

AUX 5: Press and Hold for 3 seconds.

Using the Progressive Car Finder Feature

Press the button to locate your vehicle. The system will ash the parking lights

and sound 5 times at low volume, increasing in volume each time the button is

pressed.

Using the Personal Protection Alarm (Panic)

Press and hold the button for 3 seconds to activate the personal protection alarm.

During panic mode, the normal function of the transmitter buttons will be suspended.

The transmitter’s and buttons can be used to lock and unlock the door (if the

option is installed). To stop the alarm, press and hold the button on the transmitter

again for 3 seconds. The system will automatically stop after 30 seconds.

Programmed Transmitter Notication

As a security precaution each time the vehicle’s ignition is turn on the status LED

light with ash the number of transmitters programmed into the system. This helps

to identify unauthorized transmitters from accessing your vehicle. If you believe an

unauthorized transmitter has been programmed to your system, contact your installing

dealer for assistance.

Valet Mode

When valet mode is activated the status LED will light solid, and all security functions

will be disabled. To enter or exit valet mode simply follow the steps outlined below:

1. Turn the vehicle’s ignition ON.

2. Push and hold the programming/valet button, located on the antenna.

3. The LED will turn on solid when valet mode is active

4. Release the programming/valet button.

User Selectable Notication Chirps

System ARM/DISARM chirps can be toggled ON or OFF without entering the

programming feature banks.

1. Turn the ignition ON then OFF.

2. Press and release the valet/programming button 3 times. The system

will respond with 1 chirp for ON or 2 chirps for OFF.

6ca1555E Owners revA

Carjack Mode (Anti-Hijack Mode)

This feature must be turned on in system programming, please consult your installing

dealer.

Triggering Carjack mode: While the ignition is ON and press and hold + for 2

seconds, the parking lights will ash 1 time and the system will act as follows;

1. 50 seconds after being triggered the siren will chirp for 15 seconds,

during this 15 seconds you will be alerted to push the valet button to

turn off Carjack mode. If Carjack mode is not turned off at this time it

will advance to the next step.

2. Following the 15 second chirps (total time now 65 seconds) the siren

will go into full sound and the parking lights will start ashing.

3. 90 seconds after trigger in, addition to the siren and parking lights, the

system will activate the starter kill. THE SYSTEM WILL REMAIN IN THIS

STATE UNTIL THE BATTERY IS DEPLETED.

OVERRIDE THE SYSTEM TO TURN OFF CARJACK MODE: Turn the ignition OFF

then On and press the valet button within 10 seconds.

Manually Overriding the Security System

Your system can be disarmed without the use of the transmitter. This is necessary,

since you will need the ability to operate your vehicle if the transmitter is lost or its

battery fails. To by-pass the alarm system;

1. Open the vehicle door. The alarm will sound.

2. Turn the ignition key to the ON position.

3. Within 10 seconds, press and release the valet push button switch.

The alarm system will stop sounding. You can now start and operate the vehicle

normally.

User Selectable LED

This feature will control whether the LED is ON or OFF when the system is Armed/

Locked and can be toggled ON or OFF without entering the programming feature

banks.

1. Turn the ignition ON, OFF, ON, OFF.

2. Press and release the valet/programming button 3 times. The system

will respond with 1 chirp for ON or 2 chirps for OFF.

Status LED, Light Flashes, and Siren/Horn Indications

Status LED Flash Indications

LED Flashes Function

OFF Disarmed

Slow Flash Armed

Fast Flash Passive Arming Countdown

ON (Solid) Valet Mode

2 Flashes Zone 2 Trigger, Hood / Trunk

3 Flashes Zone 3 Trigger, Door

4 Flashes Zone 4 Trigger, Shock Sensor

5 Flashes Zone 5 Trigger, Ignition

6 Flashes Zone 6 Trigger, Tilt Sensor

Siren/Horn Chirp Indications

Chirps Function

1 Disarm

2 Arm

3 Door Ajar Upon Arming

4 Disarm / Triggered

5 Car Find

Parking Light Flash Indications

Flashes Function

1 Disarm

2 Arm

3 Disarm / Triggered

5 Car Find

8ca1555E Owners revA

Check Vehicle Status

Press and release 2 times then press within 3 seconds, the transmitter will

display the current status of the vehicle.

Display Illumination

Press and hold the button for 1 second. The display will illuminate for 5 seconds.

Melody / Vibration Mode

To have the remote control vibrate, play a melody tone or both each time it receives a

response from the vehicle press and release then press and hold for 2

seconds.

Button Beeps

To toggle button beeps on or off press and release then press and hold for 2

seconds.

Battery Save Mode

While in POWER SAVE MODE the 2-way LCD transmitter will NOT look for any

incoming signals from the main unit until a button is pressed. The LCD screen will

display SAVE to indicate that power save mode is ON. To enter power save mode

press and hold for 5 seconds.

Clear Flashing Icons and Melody Sound

Press the button 3 times within 3 seconds. This will clear the melody sound and

ashing icons on the LCD screen.

Stopping LCD Trigger Melody

To stop the alarm trigger melody if the system has been triggered WITHOUT

disarming the system, press any button one time only, this will not send a command to

the vehicle at this time and the alarm will continue to sound.

Additional 2-Way LCD Remote Control Functions

Additional Features of the Optional 2 Way LCD Remote Control

Button Lock

Press and release then press hold the for 2 seconds to toggle the button lock

on or off. When the button lock is active, the remote control will beep/vibrate 2 times

when a button is pressed indicating it is locked.

Illumination

Press and release 2 times then press and hold for 2 seconds to toggle

illumination on or off. When on, the display will illuminate when it receives or sends a

command.

2 Car Mode

To control a second security system enter 2 car mode by pressing then press

and together for 3 seconds. When the icon appears on the transmitter’s LCD

screen it will control the second security system. Use the same method to exit 2 car

mode and resume control of the original vehicle’s security system.

NOTE: A second security system must be installed and the LCD transmitter must be

learned to it before this feature will operate the additional system.

Parking Meter Countdown

The parking meter countdown timer has 6 preset times, to access the preset times

and begin countdown press and release then press and hold for 2 seconds,

each additional press of will increase the countdown time.

Adjusting the Clock and Timer Settings

The clock, alarm clock and programmable countdown timer are accessed through the

Function Menu. Press and hold for 3 seconds to access the function menu, once

you have accessed the feature menu press and release to scroll through each

feature and follow the steps below to adjust the settings for each. Press and hold

for 2 seconds to exit the menu.

Clock Hour Press to increase or to decrease

Clock Minute Press to increase or to decrease

Alarm Clock Hour Press to increase or to decrease

Alarm Clock Minute Press to increase or to decrease

Alarm Clock ON / OFF Press to turn ON or to turn OFF

Countdown Timer Hour Press to increase or to decrease

Countdown Timer Minute Press to increase or to decrease

Countdown Timer ON / OFF Press to turn ON or to turn OFF

10 ca1555E Owners revA

LCD Remote Control ICON’s

LOCK UNLOCK

SYSTEM ARMED VALET MODE

TRANSMITTING

TRUNK TRIGGER DOOR TRIGGER

SHOCK / TILT TRIGGER

IGNITION ON/TRIGGER

2 CAR MODE

BATTERY INDICATORBATTERY SAVE MODE

VIBRATE/SILENT MODE

HOOD TRIGGER

SYSTEM TRIGGER TIME COUNT DOWN

MELODY MODE

TIME DISPLAY

ALARM CLOCK

AUX 1 OUTPUT

AUX MODE

AUX 5 OUTPUT

AUX 4 OUTPUT

AUX 3 OUTPUT

AUX 2 OUTPUT

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Alarma de coche de Code Alarm

Code Alarm

Code Alarm CA 610 Manual de usuario

Code Alarm

Code Alarm CA 1550 Manual de usuario

Code Alarm

Code Alarm CATX520 Instrucciones de funcionamiento

Code Alarm

Code Alarm CA 1150 Manual de usuario

Code Alarm

Code Alarm F50 Manual de usuario

Code Alarm

Code Alarm CATX630 Instrucciones de funcionamiento

Code Alarm

Code Alarm CA 680 Manual de usuario

Code Alarm

Code Alarm CA 671 Manual de usuario

Code Alarm

Code Alarm PROFESSIONAL SERIES Manual de usuario

Code Alarm

Code Alarm CSI-200 Manual de usuario

Code Alarm

Code Alarm CA1355E Manual de usuario

Code Alarm

Code Alarm CA 521 Manual de usuario

Code Alarm

Code Alarm CA 170 Manual de usuario

Code Alarm

Code Alarm Professional ca6153 Manual de usuario

Code Alarm

Code Alarm CATX510 Instrucciones de funcionamiento

Code Alarm

Code Alarm Professional 1000 Manual de usuario

Code Alarm

Code Alarm UTXPR Manual del propietario

Code Alarm

Code Alarm CA 420A Manual de usuario

Code Alarm

Code Alarm ca1555 Manual de usuario

Code Alarm

Code Alarm Vehicle Security System Manual de usuario

Code Alarm

Code Alarm PROFESSIONAL SERIES Manual de usuario

Code Alarm

Code Alarm Car Alarm CA-310 Manual de usuario

Code Alarm

Code Alarm CA- 550 Manual de usuario

Code Alarm

Code Alarm Car Alarm Manual de usuario

Manuales populares de Alarma de coche de otras marcas

Clifford

Clifford 3606X Manual de usuario

Ultra Start

Ultra Start 2500M SERIES Manual de usuario

Ultra Start

Ultra Start 650 Series Manual de usuario

Audiovox

Audiovox Prestige Platinum+ APS-511C Manual de usuario

Sparkrite

Sparkrite SRA8 Manual de usuario

Viper

Viper 4708V Manual de usuario

Federal Signal Corporation

Federal Signal Corporation Pathfinder Siren Series Manual

Falcon

Falcon Predator XL3 Guía del usuario

Audiovox

Audiovox Auto Security XR91 Instrucciones de funcionamiento

Clifford

Clifford Sabre II Manual de usuario

CrimeStopper

CrimeStopper CS-8717 Guía de inicio rápido

Ultra Start

Ultra Start 450 SERIES Manual de usuario

Scytek electronic

Scytek electronic Vectra X3 Manual de usuario

Excalibur

Excalibur AL-1860-EDPB Manual de usuario

Clifford

Clifford CYBER 2 Manual de usuario

Gemini

Gemini 7057 Manual de usuario

FlashLogic

FlashLogic FLRSBA PRESTIGE Manual de usuario

Magicar

Magicar FAI-440 Manual de usuario