Cobra 602-2000 Manual de usuario
®
23801 E. La Palma Ave., Yorba Linda, Ca 92887 Ph. 714.692.8180, Fax. 714.692.5016
www.cobrausa-hd.com
04/17 ®
1
*Cobra®recommends you always wear a helmet while riding. Please never operate your motorcycle while under
the influence of alcohol and/or drugs. Enjoy the new look of your motorcycle and please ride safely.
Items Supplied >
1 - DETACHABLE BACKREST
2 - COIL-OVER SPACERS
Application(s) >
HARLEY:
DRESSER 09-18
Instruction Manual >
Read all instructions carefully and completely before installing your new Backrest!
NOTE: You must install either a COBRA Mounting Kit (602-2100/602-2101) or a Harley Davidson 2-
point or 4 point Mounting kit before installing this backrest.
1. Remove the saddle bags carefully.
2. Install the mounting kit per the instructions that came with that kit.
3. If you are installing this backrest on a 2015-16 Street Glide Special or a 2015-16 Road Glide Special with coil-
over rear shocks you must first install the spacers supplied with the backrest between the right rear coil-over
shock and the frame and swing arm. See FIGURE 1. This will space the coil-over out far enough for the backrest
to fit properly. If your motorcycle is equipped with air shocks you do not need to install the spacers and can skip
to step 8.
SPECIAL NOTE: Some 2015 Street Glide Specials and Road Glide Specials came with the right rear coil-over
shock mounted upside down with the shock shaft pointed up. Make sure to flip the shock over if this is the case.
The shock shaft needs to be facing down as in FIGURE 1.
4. First, remove the top bolt of the right rear coil-over shock. See FIGURE 1.
5. Insert the supplied spacer between the frame and the coil-over shock and then re-install the bolt and tighten to
factory specs.
6. Then remove the bottom bolt from the right rear coil-over shock and insert the supplied spacer between the coil-
over and the swing arm. Re-install the bottom bolt and tighten to factory specifications. See FIGURE 1.
602-2000
Page 1 of 2
DOCUMENT NO. 0017 REV. A
FIGURE 1
ONLY FOR MODELS EQUIPPED
WITH COIL-OVER SHOCKS
ADD SPACER BETWEEN
COIL-OVER AND
SWING ARM
ADD SPACER BETWEEN
COIL-OVER AND
FRAME
SHOCK SHAFT
SHOULD BE DOWN
®
23801 E. La Palma Ave., Yorba Linda, Ca 92887 Ph. 714.692.8180, Fax. 714.692.5016
www.cobrausa-hd.com
04/17 ®
2
Instruction Manual >
602-2000
Page 2 of 2
8. Once the spacers have been installed on the right side coil-over (if applicable) and the mounting kit has been
installed you can install the backrest by inserting the front portions of the backrest brackets over the mounting
bosses of the rear shocks. See FIGURE 2. Make sure to insert the backrest all the way onto the bosses.
9. Then slowly rotate the backrest downward so the rear portion of the backrest brackets slips over the mounting kit
bushings. See FIGURE 2.
10. If you are using a Harley Mounting Kit you may need to adjust the width of the mounting kit bushings to align
them with the width of the backrest brackets. The Harley Mounting Kits come with spacers that may need to be
added or removed to align the width of the mounting kit bushings with the width of the backrest. Please see the
instructions that come with the mounting kit for more details.
11. Also, some Harley Mounting Kits come with oval shaped mounting bushings. These mounting bushings may
need to be rotated around the center axis of the bushing to allow for a secure fit of the detachable latch pin.
Please see the instructions of the mounting kit for more details.
12. Pull backward on both detachable latch knobs and then push downward on the backrest to allow the backrest to
sit completely on the mounting kit bushings. Then release the detachable latch knob to fully engage the latch pin
underneath the mounting kit bushing. See FIGURE 3.
13. Always check to make sure both detachable latch pins are fully engaged on the bottom of the mounting kit
bushing. Failure to fully engage the detachable latch pin could cause the backrest to come loose while riding.
14. Make any adjustments to the mounting kit bushings until the detachable backrest goes on and off easily.
15. Once all the adjustments have been made reinstall the saddle bags.
16. Before each ride, check to make sure the detachable latches are fully engaged underneath the mounting
bushings.
17. Check the tightness of all the screws after the first ride and after the first 500 miles.
DOCUMENT NO. 0018 REV. A
FIGURE 3
MAKE SURE
LATCH PIN IS
FULLY ENGAGED
UNDER BUSHING
AIR SHOCK
MOUNTING
BOSS
MOUNTING
KIT
DETACHABLE
LATCH KNOB
MOUNTING KIT
BUSHING
FIGURE 2
DETACHABLE
LATCH PIN
Tabla de contenidos
Otros manuales de Accesorios para motocicletas de Cobra
Cobra
Cobra 602-2702 Manual de usuario
Cobra
Cobra 602-2611 Manual de usuario
Cobra
Cobra Fi2000 Powrpro Manual de usuario
Cobra
Cobra 602-2610B Manual de usuario
Cobra
Cobra Ride Loud Manual de usuario
Cobra
Cobra 602-2500 Manual de usuario
Cobra
Cobra 02-6468 Manual de usuario
Cobra
Cobra POWRPRO Fi2000 Manual de usuario
Cobra
Cobra 602-2600 Manual de usuario
Cobra
Cobra Fi2000 Manual de usuario
Cobra
Cobra Fi2000 Manual de usuario
Cobra
Cobra Fi2000 PowrPro Manual de usuario
Cobra
Cobra 602-2000B Manual de usuario
Cobra
Cobra 602-2612B Manual de usuario
Cobra
Cobra Fi2000 Manual de usuario
Cobra
Cobra 01-3265 Manual de usuario
Cobra
Cobra Fi2000 PowrPro Black Manual de usuario
Cobra
Cobra 6255RB Manual de usuario
Cobra
Cobra POWRFLO Manual de usuario
Cobra
Cobra 6057 Manual de usuario
Manuales populares de Accesorios para motocicletas de otras marcas
SRC
SRC B-TRK502-01-01-SL Manual de usuario
3M
3M Speedglas 9100 MP Manual de usuario
hepco & becker
hepco & becker 6307520 00 01 Manual de usuario
HOMCOM
HOMCOM AA0-077 Manual de usuario
hepco & becker
hepco & becker 6307558 00 01 Manual de usuario
Wunderkind Custom
Wunderkind Custom 106503-F15 Guía del usuario
