Clevertronics L10 LSBLED Series Instrucciones de instalación y funcionamiento

1943071

V1.4

28 June 2022

Instruction Sheet Template - V1.3 –Updated 20/01/2022

Clevertest and Clevertest Plus

Refer to the supplementary operation guide supplied with the Product.

After Power ON, the Status LED on a Clevertest Plus enabled fitting will display a rapid Green or Red

flashing for a period up to 2 minutes.

Zoneworks, HIVE and DATA Monitored Options

Fittings with part numbers -ZW, -HV, -DATA are fitted with Zoneworks communications modules (nodes).

These fittings are monitored using either Powerline Carrier Technology that utilize the power cable to

provide data communication, RF transceiver modules operating in the ISM band or a dedicated data cable

to/from data routers installed on a dedicated data trunk connected to a central Server (can also be

connected via Ethernet/Internet/Fibre). Zoneworks software on the server is used to monitor, coordinate

testing and collate test data from each fitting. Zoneworks Fittings can be commissioned by a single push

of the test switch or by scanning the supplied barcode. The LED Test Switch indicator provides a

multifunction indication of the status of the fitting during testing and normal operation:

Option

State

LED Operation

ZW, HV, DATA

Commissioned

LED on Solid (Green)

ZW, DATA

Un-commissioned

Batt plugged-in: yellow 1s, green 1s

Batt unplugged: red 1s, off 1s

Un-commissioned

With network connectivity

Batt plugged-in: yellow 1s, green 1s

Batt unplugged: red 1s, off 1s

Un-commissioned

Without network connectivity

Batt plugged-in: yellow 250mS, green

250mS, yellow 250mS, green 250mS,

green 1s

Batt unplugged: red 250mS, off

250mS, red 250mS,off 250mS, off 1s

ZW, DATA

Emergency Light Test In Progress

LED flashes at yellow 5s , 0ff 1s

Emergency Light Test In Progress

LED flashes at yellow 1s , 0ff 1s

In the case of the DATA version a 2-way “figure 8” cable and terminal block facilitates the connection to

the DATA network via a multi-drop bus (daisy chain connection). For further information of installation of

a Zoneworks system, please refer to the Zoneworks Users Guide and Commissioning Guide (incl. DATA

version)

DALI EM Option

Luminaires with part numbers having -DALI are fitted with DALI modules (nodes) that facilitate connection

and integration to 3rd Party Lighting Control Systems. Before installing the -DALI luminaire, please confirm

that the Lighting Control System has the capability to monitor DALI Emergency Luminaires. The -DALI

fitting will be addressed and configured into the control system by the Lighting Control System

Commissioning Technicians and not Clevertronics.

State

LED Operation

Commissioned/ Un-commissioned

LED on Solid (Green)

Emergency Light Test in progress

LED flashes at 1s On (Yellow) & 1s Off

“IDENTIFY COMMAND”

Lamp and Status LED Flash for 30 seconds

A 2-way “figure 8” cable and terminal block facilitates the connection to the DALI network. DALI

connections are marked as Da Da.

L10™ Swingblade LED

Installation & Maintenance Instruction Leaflet

Victoria (Head Office & Manufacturing)

Website: www.clevertronics.com.au

Email: info@clevertronics.com.au

Phone: +61 3 9559 2700

Fax: +61 3 9559 2799

New South Wales

Phone: +61 2 8805 6400

Fax: +61 2 8805 6444

Queensland

Phone: +61 7 3442 9700

Fax: +61 7 3442 9777

South Australia/Northern Territory

Phone: +61 8 8301 8800

Fax: +61 8 8351 8286

Western Australia

Phone: +61 8 9207 0000

Fax: +61 8 9207 0088

New Zealand

Phone: +64 800 548 448

Designed in Australia to comply with the requirements

of AS2293.3: 2005 and AS/NZS CISPR15: 2017

NOTE: Standard product codes with this symbol are

enabled with Clevertest Plus capability. Please refer to the

operation guide supplied with the product for details.

Models:

LSBLED-yy-xx-ss-zz-vv

LCSBLED-yy-xx-ss-zz-vv (Classic blade option)

Testing:

Options:

Manual Test

xx = Blank

Running Man

ss=R

Black in colour

vv = BLK

Zoneworks

xx = ZW

Running Man Left

Arrow

ss=RL

Special Legend

ss = SP

Z/W DATA

xx = DATA

Running Man Right

Arrow

ss=RR

Fire Panel

Sound Control

zz = SND-24V

Zoneworks HIVE

xx = HV

Double sided R/M

ss=DS-R

Zoneworks

Sound Control

zz = SND

DALI Registered.

xx = DALI

Double sided R/M

Arrow

ss=DS-RAOW

Theatre

yy = TH

Clevertest

xx = CT

(NOTE: -CT Products supplied with the Clevertest Plus Symbol are activated with Clevertest

PLUS capability. Please refer to the operation guide supplied with the product for details).

Spare Parts:

1530070

BATT: L10 3.3V 2500mAh 200mm lead, sp.BRKT

8003212

PCA: CT10164-L6 6C83 CTP AU

8003211

PCA: CT10164-L6 6C83 DALI Reg (For -DALI and -HV only)

8003210

PCA: CT10164-L6 6C20 (Theatre, -DALI and -HV only)

8002301

PCA: CT10164-L7 TOP22x SMT 6C20 CTP ZW AU (Theatre, CTP, -ZW)

8002185

PCA:24DLED SB LED Strip, #CT10156-D2

3740010

Directional Sound Module for SwingBlade

1943071

V1.4

28 June 2022

Instruction Sheet Template - V1.3 –Updated 20/01/2022

Important:

It is illegal for anyone, except for a licensed electrician to install or maintain this product. Before installation,

ensure that the electricity supply has been switched off and isolated. Installation must be carried out in

accordance with the relevant Australian and International Standards.

Installation:

The L10 Swingblade LED Exit (LSBLED) is a surface mount (wall or ceiling) fitting. The LSBLED can be

attached directly to any solid surface, or to a ceiling tile using the integrated mounting bracket. Please

follow the steps below to install the LSBLED Exit:

•Remove the mounting bracket from the fitting.

•Using the bracket as a guide, mark 2 holes for mounting screws. Then install the bracket.

•Connect the 240VAC supply.

•Insert the LSBLED body into the bracket and slide to lock into position.

•If the CTP capabilities are activated, please affix the CTP status label to a visible surface and Four

Segment Marking on the product will include an ‘’F’’ in third segment block.

NOTE: If product is suspended below the ceiling or mounted on a metal surface the Swingblade

bracket cover plate accessory (S/N:2740100) is required to cover the mains terminals.

Networking:

When installing the product on a monitored network, (ZONEWORKS, DATA, DALI) simply insert the

relevant Smart Node PCA.

Dimensions:

Changing Diffuser Decals: (Not applicable to LCSBLED and –TH

options)

The Swingblade Exit uses Clevertronics patented “Tamper proof” Exit legend cover and comes complete with

spare legend inserts to enable straight on, left or right arrow as well as SS/DS combinations.

The tamper proof cover is held in place by 3 locking tabs recessed in the top edge of the diffuser. Use a tool to

disengage and push the locking tabs through to release the cover and remove the insert, replacing it with the

desired one.

To re-install the clear cover, first engage the three small lugs on the bottom of the cover into the respective

recesses in the diffuser. Once you are sure the lugs are located, carefully push the 3 locking tabs back in to

complete the process.

Testing:

Once connected to the 240V mains supply, the unit must be allowed to charge the battery for at least 24 hours.

Conduct the following tests:

•For the first test, the emergency lamp must remain illuminated for at least 2 hours after disconnection

from the mains supply.

•Subsequent tests require the unit to illuminate for at least 90 minutes. The results of all tests are required

to be recorded in a service logbook, which is to be kept on-site at all times. If the unit fails to remain

illuminated for the requisite time, remedial action must be taken to repair the situation and once

completed, the unit must pass a subsequent test. For more specific information, please refer to the

current edition of the AS 2293.3 Standard.

Swingblade Maintenance:

Battery/Lamp Replacement:

•Prise off the plastic end caps from ends using

a terminal screwdriver

•Disconnect the lamp lead from the PCB and

slide out the LED light bar.

•Reinsert new LED light bar, reconnect the

lamp lead and replace the plastic end cap.

•Remove the central screw connecting the two

earth leads to the earth bar. This screw holds

the equipment tray in place.

•Slide the gear tray out from the test

switch/light bar end, unplugging the AC

connector once it is revealed.

•Unplug the battery lead then bend back the

metal tabs securing the battery pack. Remove

the battery and replace with the changeover

battery pack.

Re-assemble the fitting reversing the above

procedure. It is important that the screw securing

the two earth leads is re-installed and tightened

correctly.

Trouble Shooting:

Below are a list of common problems and their

possible causes.

Fault: The Green LED Test Switch

indicator is not illuminated.

Check: A.C. is connected and is turned on.

Battery is connected

Test Switch for damage.

Fault: Lamp does not illuminate in

emergency mode.

Check: A.C. is connected.

Lamp is correctly inserted.

Battery is connected

Fault: Lamp illuminates in emergency

mode, but only stays on for a short

period.

Check: Battery has been allowed to charge for

at least 24 hours.

Battery for damage.

Rated Emergency Lumen Output in accordance with AS2293.1, not applicable

for –TH (theatre) version (refer to spacing tables for installation positions):

Refer to the Technical Label for classification information.

Caution:

On many building sites, power circuits may be cut off in an uncontrolled and repetitive basis during

construction. As a result, any Exit & Emergency Units, on these circuits, will have their batteries

discharged or “cycled”. The battery in this fitting has been selected to give excellent long-life

performance in a controlled AS2293 testing environment. Excessive battery cycling will reduce through-

life performance and may lead to premature battery failure. Battery warranty claims, as a result of such

abuse, are specifically EXCLUDED from Clevertronics warranty terms.

Warranty:

For Product Warranty information and Terms and Conditions of Sales please refer to our website

http://clevertronics.com.au/terms-conditions-sale-australia-nz/

Press locking tab and slide to remove from

bracket

Mounting Bracket

Locking

Tab

Locking

Tabs

Este manual sirve para los siguientes modelos

Otros manuales de Equipo de iluminación de Clevertronics

Clevertronics

Clevertronics ECFLED-LI Instrucciones de instalación y funcionamiento

Clevertronics

Clevertronics FVP2LED-P Series Guía de mantenimiento y servicio

Clevertronics

Clevertronics LP Ultrablade Pro CUBPRO Series Instrucciones de instalación y funcionamiento

Clevertronics

Clevertronics LIFELIGHT-2PRO-SMS-600 Instrucciones de instalación y funcionamiento

Clevertronics

Clevertronics L10 LLIFE-PRO-WP-IPREM Instrucciones de instalación y funcionamiento

Clevertronics

Clevertronics Trade TS CIRCLITE ECLLED Series Instrucciones de instalación y funcionamiento

Clevertronics

Clevertronics L10 LIFELIGHT PRO LLIFE-PRO SPOT Series Instrucciones de instalación y funcionamiento

Clevertronics

Clevertronics L10 LWPLIFE PRO Series Instrucciones de instalación y funcionamiento

Clevertronics

Clevertronics L10 Argonaut PLUS Manual de usuario

Clevertronics

Clevertronics LP CUBPRO Series Manual de usuario

Clevertronics

Clevertronics LED CIRCLITE Instrucciones de instalación y funcionamiento

Clevertronics

Clevertronics ECFLED-LI-TH Series Instrucciones de instalación y funcionamiento

Clevertronics

Clevertronics L10 LWFLED 2IPREM Series Manual de instrucciones

Clevertronics

Clevertronics L10 LJELED-40 Series Manual de usuario

Clevertronics

Clevertronics L10 LJWELED-40 Series Manual de usuario

Clevertronics

Clevertronics FBKLED Series Instrucciones de instalación y funcionamiento

Clevertronics

Clevertronics l10 LBULKy Series Instrucciones de instalación y funcionamiento

Clevertronics

Clevertronics LP LIFELIGHT PRO CLIFE PRO-SMC Series Instrucciones de instalación y funcionamiento

Clevertronics

Clevertronics L10 LIFELIGHT LLIFE-SM Series Instrucciones de instalación y funcionamiento

Clevertronics

Clevertronics L10 LUBPRO Series Instrucciones de instalación y funcionamiento

Clevertronics

Clevertronics L10 LBS2N Series Manual de instrucciones

Clevertronics

Clevertronics L10 Weatherproof Jumbo LED Exit Instrucciones de instalación y funcionamiento

Clevertronics

Clevertronics LP Argonaut PLUS Instrucciones de instalación y funcionamiento

Clevertronics

Clevertronics FBKLED Series Manual de instrucciones

Manuales populares de Equipo de iluminación de otras marcas

Brizo

Brizo 8SP-MU-4 Manual de usuario

LUCE&LIGHT

LUCE&LIGHT BROM 1.0 Manual de usuario

IKEA

IKEA BJÖRKSPIREA Manual de usuario

Laserworld

Laserworld Evolution Series ES-400RGB Manual de usuario

Alien

Alien RG STAR Manual de usuario

EuroLite

EuroLite LED B-40 Manual de usuario

Qazqa

Qazqa Suplux SL 3 Black 103062 Manual de usuario

Commercial Electric

Commercial Electric 54568141 Manual de usuario

CREE LIGHTING

CREE LIGHTING 304 Series Manual de usuario

Goobay

Goobay 49867 Manual de usuario

ECOMAN ITALIA

ECOMAN ITALIA LED T8 Manual de usuario

Alkalite

Alkalite Krypton KT-81 Manual de usuario

Clas Ohlson

Clas Ohlson GU10 Manual de usuario

DTS

DTS DELTA 10 F Manual de usuario

ring

ring Solar Steplight Manual de usuario

One Stop Gardens

One Stop Gardens 57696 Instrucciones de montaje

Chauvet DJ

Chauvet DJ COREpar UV120 ILS Manual de usuario

SIREM

SIREM Swimeo A2 Manual de usuario