Clevertronics L10 CleverFit Exit LCFLED Series Manual de usuario

1942203

V1.0

19 June 2019

Clevertest and Clevertest Plus

Refer to the supplementary operation guide supplied with the Product.

After Power ON, the Status LED on a Clevertest Plus enabled fitting will display a rapid Green or Red

flashing for a period up to 2 minutes.

Clevertest Essential

Refer to the supplementary operation guide supplied with the Product.

Zoneworks and DATA Monitored Options

Cleverfits with part numbers -ZW, -DATA are fitted with Zoneworks communications modules (nodes).

These fittings are monitored using either Powerline Carrier Technology that utilising the power cable to

provide data communication or a dedicated data cable to/from data routers installed on a dedicated data

trunk connected to a central Server (can also be connected via Ethernet/Internet/Fibre). Zoneworks

software on the server is used to monitor, coordinate testing and collate test data from each fitting.

Zoneworks Cleverfits can be commissioned bya single push of the test switch or scanning of the supplied

barcode. The LED Test Switch indicator provides a multifunction indication of the status of the fitting during

testing and normal operation:

State

LED Operation

Commissioned

LED on Solid (Green)

Un-commissioned

LED flashes at 0.5Hz (0.5s Green, 0.5s Yellow)

Emergency Light Test In Progress

LED flashes at 3s On (Yellow) & 0.5s Off

In the case of the DATA version a 2-way “figure 8” cable and terminal block facilitates the connection to

the DATA network via a multi-drop bus (daisy chain connection). For further information of installation of

a Zoneworks LW system, please refer to the Zoneworks Users Guide and Commissioning Guide (incl.

DATA version)

DALI EM Option

Cleverfits with part numbers -DALI are fitted with DALI modules (nodes) that facilitate connection and

integration to 3rd Party Lighting Control Systems. Before installing the fitting please confirm that the

Lighting Control System has the capability to monitor DALI Emergency Luminaires. The fitting will be

addressed and configured into the control system by the Lighting Control System Commissioning

Technicians and not Clevertronics.

State

LED Operation

Commissioned/ Un-commissioned

LED on Solid (Green)

Emergency Light Test in progress

LED flashes at 1s On (Yellow) & 1s Off

“IDENTIFY COMMAND”

Fitting goes into emergency mode for 10 seconds

A 2-way “figure 8” cable and terminal block facilitates the connection to the DALI network. DALI

connections are marked as Da Da.

L10™ Cleverfit LED Exit

Installation & Maintenance Instruction Leaflet

Victoria (Head Office & Manufacturing)

195 Chesterville Rd

Moorabbin VIC 3189

Phone: +61 3 9559 2700

Fax: +61 3 9559 2799

New South Wales

Phone: +61 2 8805 6400

Fax: +61 2 8805 6444

Queensland

Phone: +61 7 3442 9700

Fax: +61 7 3442 9777

South Australia/Northern Territory

Phone: +61 8 8301 8800

Fax: +61 8 8351 8286

Western Australia

Phone: +61 8 9248 3720

Fax: +61 8 9248 3725

New Zealand

Phone: +64 800 548 448

Designed in Australia to comply with the requirements of

AS2293.3: 2005 and AS/NZS CISPR15: 2011

NOTE: Standard product codes with this symbol are

enabled with Clevertest Plus capability. Please refer to the

operation guide supplied with the product for details.

Models:

LCFLED-xx-zz CleverFit Exit

LCFLED-TH-xx-yy CleverFit Theatre Exit

Testing:

Options:

Running Man

yy=R

Manual Test

xx = Blank

Running Man Left Arrow

yy=RL

Zoneworks

xx = ZW

Running Man Right Arrow

yy=RR

Z/W DATA

xx = DATA

Double sided R/M

yy=DS-R

DALI Comp

xx = DALI

Double sided R/M Arrow

yy=DS-RAOW

Clevertest Essential

xx = CTE

Black Colour

zz = BLK

Clevertest

xx = CT

(NOTE: -CT Products supplied with the Clevertest Plus Symbol are

activated with Clevertest PLUS capability. Please refer to the operation

guide supplied with the product for details).

Spare Parts:

1530090

BATTERY: L10 3.3V 2.5AH 390mm lead,noBRKT

8002430

PCA:Duris P5 6 LED Strip.L10,#CT10166-D1

8002321

PCA: LCFLED CT10164-L6 6C70 CTP DALI-COMP ZW AU

Important:

It is illegal for anyone, except for a licensed electrician to install or maintain this product. Before installation,

ensure that the electricity supply has been switched off and isolated. Installation must be carried out in

accordance with the relevant Australian and International Standards.

1942203

V1.0

19 June 2019

Installation:

The L10 Cleverfit LED Exit can be installed either Ceiling or Wall Mounted and can be mounted

perpendicular to a wall using the (optional) Cleverfit Cantilever Bracket. The fitting uses a “slide connect

bracket base” that is mounted and wired into position first. The main body can be installed once the base

is wired or later to avoid damage during the construction phase. Please follow the steps below to install

the Cleverfit Exit:

•Disengage the slide connect bracket from the exit body. Position the base in the mounting position.

•Using the bracket as a guide, mark 2 holes for mounting and one for mains access. Then install the

bracket using appropriate fixings (not supplied).

•Connect the 240VAC supply to the mounting bracket.

•Configure all the mounting parts and cable entry points as below (if required) and engage the body

into the slide connect bracket. Apply mains power and check that the Cleverfit Exit is operational.

•If the CTP capabilities are activated, please affix the CTP status Label to a visible surface.

Networking:

When installing the product on a monitored network, (ZONEWORKS, DATA, DALI) simply insert the

relevant Smart Node PCA.

Dimensions:

Testing:

Once connected to the 240V mains supply, the unit must be allowed to charge the battery for at least 24

hours. Conduct the following tests:

•For the first test, the emergency lamp must remain illuminated for at least 2 hours after

disconnection from the mains supply.

•Subsequent tests require the unit to illuminate for at least 90 minutes. The results of all tests are

required to be recorded in a service logbook, which is to be kept on-site at all times. If the unit fails

to remain illuminated for the requisite time, remedial action must be taken to repair the situation

and once completed, the unit must pass a subsequent test. For more specific information, please

refer to the current edition of the AS 2293.3 Standard.

Cleverfit Maintenance:

Lamp Replacement:

•Use only the lamp(s) recommended on the

label inside the Cleverfit.

•To replace the lamp bar, remove the self-

tapping screws, disconnect the signal cable

and install the new lamp bar.

Battery Replacement:

•Use only the battery recommended on the

label inside the Cleverfit and on this

instruction.

•Remove the cable ties holding the battery,

un-plug the lead from the PCB and remove

the old battery.

•Clip the new battery into the holder, route

the DC cable to the PCB and plug the new

battery into the PCB.

•Secure the battery using suitable cable ties

Trouble Shooting:

Below are a list of common problems and their

possible causes.

Fault: The Green LED Test Switch

indicator is not illuminated.

Check: A.C. is connected and is turned on.

Battery is connected

Test Switch for damage.

Fault: Lamp does not illuminate in

emergency mode.

Check: A.C. is connected.

Lamp is correctly inserted.

Battery is connected

Fault: Lamp illuminates in emergency

mode, but only stays on for a short

period.

Check: Battery has been allowed to charge for

at least 24 hours.

Battery for damage.

Rated Emergency Lumen Output in accordance with AS2293.1 (refer

to spacing tables for installation positions):

Refer to the Technical Label for classification information.

Caution:

On many building sites, power circuits may be cut off in an uncontrolled and repetitive basis during

construction. As a result, any Exit & Emergency Units, on these circuits, will have their batteries

discharged or “cycled”. The battery in this fitting has been selected to give excellent long-life

performance in a controlled AS2293 testing environment. Excessive battery cycling will reduce through-

life performance and may lead to premature battery failure. Battery warranty claims, as a result of such

abuse, are specifically EXCLUDED from Clevertronics warranty terms.

Warranty:

For Product Warranty information and Terms and Conditions of Sales please refer to our website

http://clevertronics.com.au/terms-conditions-sale-australia-nz/

Este manual sirve para los siguientes modelos

Otros manuales de Equipo de iluminación de Clevertronics

Clevertronics

Clevertronics LIFELIGHT-2PRO-SMS-600 Instrucciones de instalación y funcionamiento

Clevertronics

Clevertronics EJELED-40-LI Instrucciones de instalación y funcionamiento

Clevertronics

Clevertronics LP Cleverfit Pro CCFPRO TH Series Instrucciones de instalación y funcionamiento

Clevertronics

Clevertronics CLP Argonaut ARGOSQ-LP Series Manual de usuario

Clevertronics

Clevertronics LP CWP2LIFE-PRO-WPPOD Series Instrucciones de instalación y funcionamiento

Clevertronics

Clevertronics Trade Series Manual

Clevertronics

Clevertronics L10 Cleverfit Pro LCFPRO-TH Series Instrucciones de instalación y funcionamiento

Clevertronics

Clevertronics LP CBS4LEDS DIF Series Especificaciones técnicas

Clevertronics

Clevertronics CleverEVAC LP Cleverfit Pro DYRC CP Series Instrucciones de instalación y funcionamiento

Clevertronics

Clevertronics L10 LSBLED Series Instrucciones de instalación y funcionamiento

Clevertronics

Clevertronics L10 LUBPRO Series Manual

Clevertronics

Clevertronics L10 Argonaut PLUS Manual de usuario

Clevertronics

Clevertronics CBULKy Series Instrucciones de instalación y funcionamiento

Clevertronics

Clevertronics ECFLED-LI-TH Series Instrucciones de instalación y funcionamiento

Clevertronics

Clevertronics Nifty Lifelight Surface Mount Instrucciones de instalación y funcionamiento

Clevertronics

Clevertronics L10 LJELED-40 Series Manual de usuario

Clevertronics

Clevertronics L10 Weatherproof Jumbo LED Exit Instrucciones de instalación y funcionamiento

Clevertronics

Clevertronics L10 LIFELIGHT PRO LWPLIFE-PRO-CM Series Instrucciones de instalación y funcionamiento

Clevertronics

Clevertronics L10 Cleverfit Pro Instrucciones de instalación y funcionamiento

Clevertronics

Clevertronics L10 Supalite LFLLED Series Manual de usuario

Clevertronics

Clevertronics TS EUBPRO-LI Instrucciones de instalación y funcionamiento

Clevertronics

Clevertronics L10 LIFELIGHT PRO Manual de usuario

Clevertronics

Clevertronics LP LIFELIGHT CLIFE-RECSP Series Instrucciones de instalación y funcionamiento

Clevertronics

Clevertronics CLP CWSQLED Series Manual

Manuales populares de Equipo de iluminación de otras marcas

Brizo

Brizo 8SP-MU-4 Manual de usuario

LUCE&LIGHT

LUCE&LIGHT BROM 1.0 Manual de usuario

IKEA

IKEA BJÖRKSPIREA Manual de usuario

Laserworld

Laserworld Evolution Series ES-400RGB Manual de usuario

Alien

Alien RG STAR Manual de usuario

EuroLite

EuroLite LED B-40 Manual de usuario

Qazqa

Qazqa Suplux SL 3 Black 103062 Manual de usuario

Commercial Electric

Commercial Electric 54568141 Manual de usuario

CREE LIGHTING

CREE LIGHTING 304 Series Manual de usuario

Goobay

Goobay 49867 Manual de usuario

ECOMAN ITALIA

ECOMAN ITALIA LED T8 Manual de usuario

Alkalite

Alkalite Krypton KT-81 Manual de usuario

Clas Ohlson

Clas Ohlson GU10 Manual de usuario

DTS

DTS DELTA 10 F Manual de usuario

ring

ring Solar Steplight Manual de usuario

One Stop Gardens

One Stop Gardens 57696 Instrucciones de montaje

Chauvet DJ

Chauvet DJ COREpar UV120 ILS Manual de usuario

SIREM

SIREM Swimeo A2 Manual de usuario