Clevertronics LP CBS4N Series Instrucciones de instalación y funcionamiento

1942409 V1.1 3 June 2021

Clevertest and Clevertest Plus

Refer to the supplementary operation guide supplied with the Product.

After Power ON, the Status LED on a Clevertest Plus enabled fitting will display a rapid Green or Red

flashing for a period up to 2 minutes.

Zoneworks, HIVE and DATA Monitored Options

Fittings with part numbers -ZW, -HV, -DATA are fitted with Zoneworks communications modules (nodes).

These fittings are monitored using either Powerline Carrier Technology that utilize the power cable to

provide data communication, RF transceiver modules operating in the ISM band or a dedicated data cable

to/from data routers installed on a dedicated data trunk connected to a central Server (can also be

connected via Ethernet/Internet/Fibre). Zoneworks software on the server is used to monitor, coordinate

testing and collate test data from each fitting. Zoneworks Fittings can be commissioned by a single push

of the test switch or by scanning the supplied barcode. The LED Test Switch indicator provides a

multifunction indication of the status of the fitting during testing and normal operation:

Option

State

LED Operation

ZW, HV, DATA

Commissioned

LED on Solid (Green)

ZW, DATA

Un-commissioned

Batt plugged-in: yellow 1s, green 1s

Batt unplugged: red 1s, off 1s

Un-commissioned

With network connectivity

Batt plugged-in: yellow 1s, green 1s

Batt unplugged: red 1s, off 1s

Un-commissioned

Without network connectivity

Batt plugged-in: yellow 250mS, green

250mS, yellow 250mS, green 250mS,

green 1s

Batt unplugged: red 250mS, off

250mS, red 250mS,off 250mS, off 1s

ZW, DATA

Emergency Light Test In Progress

LED flashes at yellow 5s , 0ff 1s

Emergency Light Test In Progress

LED flashes at yellow 1s , 0ff 1s

In the case of the DATA version a 2-way “figure 8” cable and terminal block facilitates the connection to

the DATA network via a multi-drop bus (daisy chain connection). For further information of installation of

a Zoneworks system, please refer to the Zoneworks Users Guide and Commissioning Guide (incl. DATA

version)

DALI EM Option

Fittings with part numbers CBS4N-DALI are fitted with DALI modules (nodes) that facilitate connection

and integration to 3rd Party Lighting Control Systems. Before installing the CBS4N -DALI please confirm

that the Lighting Control System has the capability to monitor DALI Emergency Luminaires. The CBS4N-

DALI will be addressed and configured into the control system by the Lighting Control System

Commissioning Technicians and not Clevertronics.

State

LED Operation

Commissioned/ Un-commissioned

LED on Solid (Green)

Emergency Light Test in progress

LED flashes at 1s On (Yellow) & 1s Off

“IDENTIFY COMMAND”

Fitting goes into emergency mode for 10 seconds

A 2-way “figure 8” cable and terminal block facilitates the connection to the DALI network OR a 5/6way

“structured wiring system” lead and plug facilitating the power and DALI connection. DALI connections

are marked as Da Da.

LP™ Non-Maintained Batten

Surface Mount Emergency Luminaire

Installation & Maintenance Instruction Leaflet

Designed in Australia to comply with the

requirements of AS2293.3: 2005 and AS/NZS

CISPR15: 2017.

NOTE: Standard product codes with this symbol

are enabled with Clevertest Plus capability.

Please refer to the operation guide supplied with

the product for details.

Victoria (Head Office & Manufacturing)

Website: www.clevertronics.com.au

Email: info@clevertronics.com.au

Phone: +61 3 9559 2700

Fax: +61 3 9559 2799

New South Wales

Phone: +61 2 8805 6400

Fax: +61 2 8805 6444

Queensland

Phone: +61 7 3442 9700

Fax: +61 7 3442 9777

South Australia/Northern Territory

Phone: +61 8 8301 8800

Fax: +61 8 8351 8286

Western Australia

Phone: +61 8 9248 3720

Fax: +61 8 9248 3725

New Zealand

Phone: +64 800 548 448

Models: CBS4N-xx-yy-zz

Testing:

Options:

Manual Test

xx = Blank

Black Colour

zz = BLK

Zoneworks

xx = ZW

Flex & Plug with Flat Earth

yy=FPF

Zoneworks DATA

xx = DATA

DALI

xx = DALI

HIVE

xx = HV

Clevertest

xx = CT (NOTE: Products supplied with the Clevertest Plus Symbol are activated

with Clevertest PLUS capability. Please refer to the operation guide supplied with the

product for details).

Spare Parts:

1550230

Battery, LP 3.2V 6400mAh, 200mm Lead Bracket

1100866

Lifelight Pro Head Assembly, Ld:500mm, Rnd, LT, Gen 2

AUM02370050001

CLIFE-PRO-CKIT-NP, Lifelight Pro, Control Only, 530mm, NP, CTP, OWC

Important:

It is illegalfor anyone, except for alicensed electrician toinstall ormaintainthis product. Before installation,

ensure that the electricity supply has been switched off and isolated. Installation must be carried out in

accordance with the relevant Australian and International Standards.

1942409 V1.1 3 June 2021

Installation:

This CBS4N Surface mount non-maintained Emergency Luminaire can be installed on solid surface or

used to replace an existing unit.

•Locate the installation position.

•Refer Images and Dimensions below for the Cut-out Hole and other dimensions.

•Pre-drill mounting holes.

•Mount base plate and use suitable fixings to secure the base plate into the pilot holes

•Bring in supply cables via the rear entry hole or via the end of the base plate (surface mount

conduit entry)

•Terminate the supply cables to the L, N & E terminals (in the case of the –DALI or –DATA fittings

terminate the DALI or DATA cable to the terminals marked Da Da or DATA).

•Install the top cover, containing the LifeLight Pro heads, ensuring to reconnect the Heads assembly

to the Control Gear.

•Ensure the Battery is connected

•Screw the cover to the base plate.

•If the CTP capabilities are activated, please affix the CTP Status Label to a visible surface and

Four Segment Marking on the product will include an ‘’F’’ in third segment block.

Networking:

When installing the product on a monitored network, (ZONEWORKS, DATA, HIVE, DALI) simply insert

the relevant Smart Node PCA.

Images and Dimensions:

Initial Testing:

When the CBS4N unit is connected to the un-switched active, it must be allowed to charge the battery

for at least 24 hours. The emergency lamp only illuminates during a power failure. Conduct the following

tests:

•During the first commissioning test the emergency lamp must illuminate for at least 2 hours after

disconnection from the main supply. The results of all tests are required to be recorded in a service

logbook, which is to be kept on-site at all times. If the unit fails to illuminate for the requisite time,

remedial action must be taken to repair the situation and once completed, the unit must pass a

subsequent test.

•Press and hold Test Button for each LED head or switch Off Mains Supply, check that the

emergency lamps are On.

•Release the Test Button or Switch on Mains Supply, check that the emergency lamp is Off (Non-

maintained operation).

Below are a list of common problems and their possible causes:

Fault: The Green LED indicator is not illuminated.

Check: A.C. is connected and is turned on.

Battery is connected.

Test Switch for damage.

Fault: Lamp does not illuminate in emergency mode.

Check: A.C. is connected.

Lamp is correctly inserted.

Battery is connected

Fault: Lamp illuminates in emergency mode, but only stays on for a short period.

Check: Battery has been allowed to charge for at least 24 hours.

Battery for damage.

Rated Emergency Lumen Output in accordance with AS2293.1 (refer

to spacing tables for installation positions):

Refer to the Technical Label on the Product for classification information.

Caution:

On many building sites, power circuits may be cut off in an uncontrolled and repetitive basis during

construction. As a result, any fittings Units, on these circuits, will have their batteries discharged or

“cycled”. The Li-ion battery in the Fitting has been selected to give excellent long-life performance in a

controlled IEC 60598-2-22 testing environment. Excessive battery cycling will reduce through-life

performance and may lead to premature battery failure. Battery warranty claims, as a result of such

abuse, are specifically EXCLUDED from Clevertronics warranty terms.

Warranty:

For Product Warranty information and Terms and Conditions of Sales please refer to our website

http://clevertronics.com.au/terms-conditions-sale-australia-nz/

Cable entry points

End view

Chain suspension points

Surface suspension points

Otros manuales de Equipo de iluminación de Clevertronics

Clevertronics

Clevertronics L10 Argonaut PLUS Manual de usuario

Clevertronics

Clevertronics L10 LIFELIGHT LLIFE Series Instrucciones de instalación y funcionamiento

Clevertronics

Clevertronics LP Argonaut Manual de instrucciones

Clevertronics

Clevertronics ARGO-1200 EM Series Especificaciones técnicas

Clevertronics

Clevertronics LP CUBPRO Series Manual de usuario

Clevertronics

Clevertronics L10 ARGOPRO-1200-L10POD Series Manual de usuario

Clevertronics

Clevertronics FBKLED Series Instrucciones de instalación y funcionamiento

Clevertronics

Clevertronics GLIDER-SM Instrucciones de instalación y funcionamiento

Clevertronics

Clevertronics LP CSBLED Series Instrucciones de instalación y funcionamiento

Clevertronics

Clevertronics L10 LIFELIGHT PRO LWPLIFE-PRO-CM Series Instrucciones de instalación y funcionamiento

Clevertronics

Clevertronics LP CWSQLED Series Manual de usuario

Clevertronics

Clevertronics TS EUBPRO-LI Instrucciones de instalación y funcionamiento

Clevertronics

Clevertronics LP Ultrablade Pro CUBPRO Series Instrucciones de instalación y funcionamiento

Clevertronics

Clevertronics L10 LUBPRO Series Instrucciones de instalación y funcionamiento

Clevertronics

Clevertronics L10 Cleverfit Pro LCFPRO-TH Series Instrucciones de instalación y funcionamiento

Clevertronics

Clevertronics L10 Ultrablade Pro LUBPRO-SM Series Manual de instrucciones

Clevertronics

Clevertronics L10 LSBLED Series Instrucciones de instalación y funcionamiento

Clevertronics

Clevertronics CLP Argonaut ARGOSQ-LP Series Manual de usuario

Clevertronics

Clevertronics CleverEVAC L10 UltraBlade Pro Dynamic Red Instrucciones de instalación y funcionamiento

Clevertronics

Clevertronics L10 LIFELIGHT PRO LLIFE PRO Series Manual de usuario

Clevertronics

Clevertronics LP LIFELIGHT PRO CLIFE-PRO-SMS-SPOT Series Instrucciones de instalación y funcionamiento

Clevertronics

Clevertronics LP Cleverfit Pro CCFPRO TH Series Instrucciones de instalación y funcionamiento

Clevertronics

Clevertronics LED CIRCLITE Instrucciones de instalación y funcionamiento

Clevertronics

Clevertronics Glider Instrucciones de instalación y funcionamiento

Manuales populares de Equipo de iluminación de otras marcas

Brizo

Brizo 8SP-MU-4 Manual de usuario

LUCE&LIGHT

LUCE&LIGHT BROM 1.0 Manual de usuario

IKEA

IKEA BJÖRKSPIREA Manual de usuario

Laserworld

Laserworld Evolution Series ES-400RGB Manual de usuario

Alien

Alien RG STAR Manual de usuario

EuroLite

EuroLite LED B-40 Manual de usuario

Qazqa

Qazqa Suplux SL 3 Black 103062 Manual de usuario

Commercial Electric

Commercial Electric 54568141 Manual de usuario

CREE LIGHTING

CREE LIGHTING 304 Series Manual de usuario

Goobay

Goobay 49867 Manual de usuario

ECOMAN ITALIA

ECOMAN ITALIA LED T8 Manual de usuario

Alkalite

Alkalite Krypton KT-81 Manual de usuario

Clas Ohlson

Clas Ohlson GU10 Manual de usuario

DTS

DTS DELTA 10 F Manual de usuario

ring

ring Solar Steplight Manual de usuario

One Stop Gardens

One Stop Gardens 57696 Instrucciones de montaje

Chauvet DJ

Chauvet DJ COREpar UV120 ILS Manual de usuario

SIREM

SIREM Swimeo A2 Manual de usuario