Clevertronics LP CBS2LEDS-DIF Series Especificaciones técnicas

1942311 V1.3 6 May 2022

Clevertest and Clevertest Plus

Refer to the supplementary operation guide supplied with the Product.

After Power ON, the Status LED on a Clevertest Plus enabled fitting will display a rapid Green or Red

flashing for a period up to 2 minutes.

Zoneworks, HIVE (HV/HVG) and DATA Monitored Options

Fittings with part numbers -ZW, -HV, -HVG, -DATA are fitted with Zoneworks communications modules

(nodes). These fittings are monitored using either Powerline Carrier Technology that utilize the power

cable to provide data communication, RF transceiver modules operating in the ISM band or a dedicated

data cable to/from data routers installed on a dedicated data trunk connected to a centralServer (can also

be connected via Ethernet/Internet/Fibre). Zoneworks software on the server is used to monitor,

coordinate testing and collate test data from each fitting. Zoneworks Fittings can be commissioned by a

single push of the test switch or by scanning thesuppliedbarcode. The LED Test Switch indicator provides

a multifunction indication of the status of the fitting during testing and normal operation:

Option

State

LED Operation

ZW, HV, HVG,

DATA

Commissioned

LED on Solid (Green)

ZW, DATA

Un-commissioned

Batt plugged-in: yellow 1s, green 1s

Batt unplugged: red 1s, off 1s

HV, HVG

Un-commissioned

With network connectivity

Batt plugged-in: yellow 1s, green 1s

Batt unplugged: red 1s, off 1s

HV, HVG

Un-commissioned

Without network connectivity

Batt plugged-in: yellow 250mS, green

250mS, yellow 250mS, green 250mS,

green 1s

Batt unplugged: red 250mS, off

250mS, red 250mS,off 250mS, off 1s

ZW, DATA

Emergency Light Test In Progress

LED flashes at yellow 5s , 0ff 1s

HV, HVG

Emergency Light Test In Progress

LED flashes at yellow 1s , 0ff 1s

In the case of the DATA version a 2-way “figure 8” cable and terminal block facilitates the connection to

the DATA network via a multi-drop bus (daisy chain connection). For further information of installation of

a Zoneworks system, please refer to the Zoneworks Users Guide and Commissioning Guide (incl. DATA

version)

DALI EM Option

LP battens with part numbers -DALI are fitted with DALI modules (nodes) that facilitate connection and

integration to 3rd Party Lighting Control Systems. Before installing the -DALI batten, please confirm that

the Lighting Control System has the capability to monitor DALI Emergency Luminaires. The batten will

be addressed and configured into the control system by the Lighting Control System Commissioning

Technicians and not Clevertronics.

State

LED Operation

Commissioned/ Un-commissioned

LED on Solid (Green)

Emergency Light Test in progress

LED flashes at 1s On (Yellow) & 1s Off

“IDENTIFY COMMAND”

Lamp and Status LED Flash for 30 seconds

A 2-way “figure 8” cable and terminal block facilitates the connection to the DALI network OR a 5/6way

“structured wiring system” lead and plug facilitating the power and DALI connection. DALI connections

are marked as Da Da.

LP™ Sustained Emergency LED Battens

Installation & Maintenance Instruction Leaflet

Designed in Australia to comply with the

requirements of AS2293.3: 2005 and AS/NZS

CISPR15: 2011.

NOTE: Standard product codes with this symbol are

enabled with Clevertest Plus capability. Please refer to

the operation guide supplied with the product for details.

Models: CBS2LEDS-DIF-yy-zz-vv-xx

Victoria (Head Office & Manufacturing)

Website: www.clevertronics.com.au

Email: info@clevertronics.com.au

Phone: +61 3 9559 2700

Fax: +61 3 9559 2799

New South Wales

Phone: +61 2 8805 6400

Fax: +61 2 8805 6444

Queensland

Phone: +61 7 3442 9700

Fax: +61 7 3442 9777

South Australia/Northern Territory

Phone: +61 8 8301 8800

Fax: +61 8 8351 8286

Western Australia

Phone: +61 8 9207 0000

Fax: +61 8 9207 0088

New Zealand

Phone: +64 800 548 448

Testing:

Manual Test

yy = Blank

Options:

Zoneworks

yy = ZW

On/Off Sensor Control

zz = MS

Zoneworks DATA

yy = DATA

DALI Driver

zz = DD

DALI

yy = DALI

Black Colour

xx = BLK

HIVE

yy = HV/HVG

4 Hour Battery

vv = 4HR

Clevertest

yy = CT (NOTE: Products supplied with the Clevertest Plus Symbol are

activatedwith Clevertest PLUScapability. Please refer to the operation guide

supplied with the product for details).

Spare Parts:

1550050

Replacement Battery

1100634

Replacement 240V LED Strip

1100641

Replacement 240V LED Strip (For -4HR)

AUM02370170001

Replacement Emergency Driver

AUM02870100001 / AUM02970060001

Replacement Emergency Driver (For -HV / -HVG)

AUM02270170002

Replacement Emergency Driver (For -DALI)

AUM02370080001

Replacement Emergency Driver (For -4HR)

8002695

Replacement Emergency LED Board

1330029

Replacement 240V Driver

1330038

Replacement 240V Driver (-DD Option)

Important:

It is illegal for anyone, except for a licensed electrician to install or maintain this product. Before installation, ensure that

the electricity supply has been switched off and isolated. Installation must be carried out in accordance with the relevant

Australian and International Standards.

1942311 V1.3 6 May 2022

Installation:

This LP Emergency batten can be wall or ceiling mounted.

•Refer Images below for the mounting hole, cable access and other dimensions.

•Remove the diffuser.

•Remove the cover plate and disconnect the LED strip connector. Unhook the lanyard

•Position the batten in the desired location.

•Mark out the fixing points on the mounting surface.

•Install appropriate fixing hardware.

•Route power supply cables through the access hole as the rear of the fitting or the ends if using

surface conduit (punch out the knock-outs in the plastic end caps)

•Fasten the batten to the surface.

•Terminate the supply cable to the terminals marked AEM, N, ASW and E (240V AC/50Hz)

•Attach the cover plate to lanyard, Re-connect the LED strip connector and Re-attach the cover

plate onto the body of the batten.

•Re-install the diffuser

•If the CTP capabilities are activated, please affix the CTP status label to a visible surface and Four

Segment Marking on the product will include an ‘’F’’ in third segment block.

Images and Dimensions:

Testing:

When the LP batten unit is connected to the un-switched active, it must be allowed to charge the battery

for at least 24 hours. The emergency lamp only illuminates during a power fail. Conduct the following

tests:

•The emergency lamp must illuminate for at least 2 hours after disconnection from the mains. The

results of all tests are required to be recorded in a service logbook, which is to be kept on-site at all

times. If the unit fails to illuminate for the requisite time, remedial action must be taken to repair the

situation and once completed, the unit must pass a subsequent test.

•Press and hold Test Button or switch Off Mains Supply, check that the emergency lamp is On.

•Release the Test Button or Switch On Mains Supply, check that the emergency lamp is Off (Non-

maintained operation).

Below are a list of common problems and their possible causes:

Fault: The Green LED indicator is not illuminated.

Check: A.C. is connected and is turned on.

Battery is connected.

Test Switch for damage.

Fault: Lamp does not illuminate in emergency mode.

Check: A.C. is connected.

Lamp is correctly inserted.

Battery is connected

Fault: Lamp illuminates in emergency mode, but only stays on for a short period.

Check: Battery has been allowed to charge for at least 24 hours.

Battery for damage.

Rated Emergency Lumen Output in accordance with AS2293.1 (refer

to spacing tables for installation positions):

Refer to the Technical Label for classification information.

Caution:

On many building sites, power circuits may be cut off in an uncontrolled and repetitive basis during

construction. As a result, any LP battens, on these circuits, will have their batteries discharged or

“cycled”. The Li-ion battery in the LP batten has been selected to give excellent long-life performance in

a controlled IEC 60598-2-22 testing environment. Excessive battery cycling will reduce through-life

performance and may lead to premature battery failure. Battery warranty claims, as a result of such

abuse, are specifically EXCLUDED from Clevertronics warranty terms.

Warranty:

For Product Warranty information and Terms and Conditions of Sales please refer to our website

http://clevertronics.com.au/terms-conditions-sale-australia-nz/

Otros manuales de Equipo de iluminación de Clevertronics

Clevertronics

Clevertronics L10 LBLLED-REC-WM Series Manual de usuario

Clevertronics

Clevertronics L10 LWPLIFE PRO Series Instrucciones de instalación y funcionamiento

Clevertronics

Clevertronics LP CWSQLED Series Manual de usuario

Clevertronics

Clevertronics L10 LIFELIGHT PRO LLIFE-PRO SPOT Series Instrucciones de instalación y funcionamiento

Clevertronics

Clevertronics ARGO-1200 EM Series Especificaciones técnicas

Clevertronics

Clevertronics L10 LVP2LEDM-P Series Instrucciones de instalación y funcionamiento

Clevertronics

Clevertronics TS Trade Series Instrucciones de instalación y funcionamiento

Clevertronics

Clevertronics L10 LLIFE-PRO-WP-IPREM Instrucciones de instalación y funcionamiento

Clevertronics

Clevertronics LIFELIGHT-2PRO-SMS-600 Instrucciones de instalación y funcionamiento

Clevertronics

Clevertronics L10 Ultrablade Pro LUBPRO-SM Series Manual de instrucciones

Clevertronics

Clevertronics LP LIFELIGHT PRO Instrucciones de instalación y funcionamiento

Clevertronics

Clevertronics CleverEVAC L10 UltraBlade Pro Dynamic Red Instrucciones de instalación y funcionamiento

Clevertronics

Clevertronics LP CBS4LEDS DIF Series Especificaciones técnicas

Clevertronics

Clevertronics L10 Lifelight Pro LWPLIFE-PRO-WM Series Instrucciones de instalación y funcionamiento

Clevertronics

Clevertronics LP Cleverfit CCFLED Series Instrucciones de instalación y funcionamiento

Clevertronics

Clevertronics TS Trade Series Instrucciones de instalación y funcionamiento

Clevertronics

Clevertronics L10 Supalite LFLLED Series Manual de usuario

Clevertronics

Clevertronics CleverEVAC LP Cleverfit Pro DYRC CP Series Instrucciones de instalación y funcionamiento

Clevertronics

Clevertronics l10 LBULKy Series Instrucciones de instalación y funcionamiento

Clevertronics

Clevertronics CLP Argonaut ARGOSQ-LP Series Manual de usuario

Clevertronics

Clevertronics CleverEVAC LP UltraBlade DYGC UP Series Instrucciones de instalación y funcionamiento

Clevertronics

Clevertronics CLP CWSQLED Series Manual

Clevertronics

Clevertronics ARGOPRO-1200 Series Manual de usuario

Clevertronics

Clevertronics CLP LIFELIGHT PRO Especificaciones técnicas

Manuales populares de Equipo de iluminación de otras marcas

Brizo

Brizo 8SP-MU-4 Manual de usuario

LUCE&LIGHT

LUCE&LIGHT BROM 1.0 Manual de usuario

IKEA

IKEA BJÖRKSPIREA Manual de usuario

Laserworld

Laserworld Evolution Series ES-400RGB Manual de usuario

Alien

Alien RG STAR Manual de usuario

EuroLite

EuroLite LED B-40 Manual de usuario

Qazqa

Qazqa Suplux SL 3 Black 103062 Manual de usuario

Commercial Electric

Commercial Electric 54568141 Manual de usuario

CREE LIGHTING

CREE LIGHTING 304 Series Manual de usuario

Goobay

Goobay 49867 Manual de usuario

ECOMAN ITALIA

ECOMAN ITALIA LED T8 Manual de usuario

Alkalite

Alkalite Krypton KT-81 Manual de usuario

Clas Ohlson

Clas Ohlson GU10 Manual de usuario

DTS

DTS DELTA 10 F Manual de usuario

ring

ring Solar Steplight Manual de usuario

One Stop Gardens

One Stop Gardens 57696 Instrucciones de montaje

Chauvet DJ

Chauvet DJ COREpar UV120 ILS Manual de usuario

SIREM

SIREM Swimeo A2 Manual de usuario