Clarke CSE2 Manual de instrucciones

OPERATION & MAINTENANCE

INSTRUCTIONS

GC11/18 - ISS 2

ORIGINAL INSTRUCTIONS

SUBMERSIBLE WATER PUMPS

MODEL NO: CSE2,CSD3,CSV1A,CSV2A

PART NO: 7230560, 7230610, 7230580, 7230600

INTRODUCTION

Thank you for purchasing this CLARKE Submersible Water Pump. CSE pumps

are designed for pumping clean water only and will pump down to a water

level of 20mm.

This pump is designed for pumping clean water or water containing solids in

suspension and is ideally suited for draining ponds, pools, sumps etc. It is not

designed for pumping slurry, sludge, mud or heavily polluted water, or any

water containing chemicals or other acidic contaminants including salt water.

Pumps fitted with float switches are suitable for permanent or semi-permanent

installations where it is necessary to maintain water at a particular level.

As the water level rises, the float switch will rise and start the pump. As the

water level falls, so will the float switch until it stops the pump. Float switches

are factory set to provide the correct on/off switching mode, however, you

can adjust the level at which the pump cuts out by sliding the float switch

cable in its clip attached to the handle, to either shorten or lengthen as

required. The shorter the cable, the earlier it will cut out and therefore, the

deeper the water will remain at this point.

PUMP SPECIFICATION

CSE2 CSD3 CSV1A CSV2A

Dimensions excluding

the elbow

140 x

302mm

149 x

400mm

143 x

300mm

143 x

335mm

Weight 4.3kg 8.0 kg 4.6 kg 5.6 kg

Cable Size 10 x 0.75

(m x mm2)

15 x 1.0 (m

x mm2)

10 x 0.75

(m x mm2)

10 x 0.75

(m x mm2)

Max. Capacity 253 L/min 95 L/min 118 L/min 236 L/min

Head Max 10 m 45 m 5 m 9 m

Motor Output 750 W 900 W 330 W 650 W

Outlet Diameter 1¼”/

32mm

1”/ 25mm 1¼”/

32mm

1¼”/

32mm

SAFETY PRECAUTIONS

1. These pumps are designed to pump WATER ONLY. Never use for pumping

flammable liquids or chemicals.

2. Never run the pump dry.

3. An approved Residual Current Device (RCD) which has a tripping current

of less than 30mA must be used when pumping from ponds or swimming

pools.

4. Never carry the pump by the mains lead or float switch.

5. Never pull the mains lead to disconnect the pump from the mains socket.

6. Your submersible pump may only be used for pumping water from a

swimming pool when there is no person or animal in the pool.

7. Always disconnect the pump from the electrical supply before placing it

into, or removing it from the water and before any cleaning or

maintenance.

8. Always use the moulded handle (or lifting eye), with a rope or cable

attached when lifting the pump. NEVER lift the pump by the mains cable

or, where fitted, the float switch cable.

9. DO NOT run the pump with the body exposed for longer than 10 minutes.

10. DO NOT install the pump on sand or ground which is likely to shift.

11. Do not use the pump if the water is liable to freeze, as this can cause

damage to the pump. Remove the pump from the water and store it in a

frost free location.

12. If the pump is to be used where there may be silt or mud (for example,

garden ponds), keep the pump clear of any sediment by standing it on a

platform or brick.

13. Do not allow children to touch the pump, cables or connections.

14. Disconnect the pump from the mains supply when not in use.

15. Have the pump repaired by a qualified person.

16. Keep the mains cable away from heat, oil and sharp edges.

17. Always check the plug, mains cable and float switch cable for damage

before use. Do not use the pump if damaged. Refer to qualified service

personnel for repair.

18. If you have to use an extension lead with this product, it must be designed

for outdoor use and incorporate a cable suitable for use with Class I

appliances.

ELECTRICAL CONNECTIONS

Connect the mains lead to a standard, 230 Volt (50Hz) electrical supply

through an approved 13 amp BS 1363 plug, or a suitably fused isolator switch.

If the plug has to be changed because it is not suitable for your socket, or

because of damage, it must be removed and a replacement fitted, following

the wiring instructions shown below. The old plug must be discarded safely, as

insertion into a power socket could cause an electrical hazard.

If the colours of the wires in the power cable do not agree with the markings

on the plug.

• The BLUE wire must be

connected to the

terminal which is

marked N or coloured

black.

• The BROWN wire must

be connected to the

terminal which is

marked L or coloured

red.

• The YELLOW AND

GREEN wire must be

connected to the terminal which is marked E or or coloured green.

AN APPROVED RESIDUAL CURRENT DEVICE (RCD) WHICH HAS A TRIPPING

CURRENT OF LESS THAN 30 mA MUST BE USED.

If you are not sure, consult a qualified electrician. DO NOT try to do any

repairs.

WARNING: READ THESE ELECTRICAL SAFETY INSTRUCTIONS

THOROUGHLY BEFORE CONNECTING THE PRODUCT TO THE MAINS

SUPPLY.

WARNING: THE WIRES IN THE POWER CABLE OF THIS PRODUCT ARE

COLOURED IN ACCORDANCE WITH THE FOLLOWING CODE:

BLUE = NEUTRAL BROWN = LIVE YELLOW AND GREEN = EARTH

Plug must be BS1363/A approved.

Always fit

Ensure that the outer sheath of

Neutral

(Blue)

Live

(Brown)

Earth

(Green and

a 13 Amp

the cable is firmly held by the clamp

fuse.

Yellow)

PREPARATION

ELBOW

Fit the elbow adaptor to the

pump outlet as shown in the

diagram opposite.

2. Screw the multi-hose adaptor

onto the elbow.

• The multi hose adaptor is

capable of accepting 1”,

¾”and ½” hoses.

1”

¾”

½”

Simply cut the multi hose

connector to the required size

and attach a suitable hose using

with a worm drive clip.

• For maximum efficiency, we

strongly recommend that you

connect a 1¼” diameter hose

to the multi hose adapter.

• Alternatively, you may remove

the multi adapter altogether,

and screw on a 1¼” BSP hose adapter.

The pump is completely submersible and should be placed in a vertical

position on a solid flat surface, placing the pump on a couple of house bricks if

required.

SUITABLE HOSES AND SPARE/REPLACEMENT MULTI HOSE ADAPTERS ARE

AVAILABLE FROM YOUR CLARKE DEALER.

WARNING: DISCONNECT THE PUMP FROM THE MAINS POWER SUPPLY

BEFORE CONNECTING THE MULTI HOSE ADAPTOR.

USING THE PUMP

1. Place the pump on a flat surface in the area that you want to drain.

• If there is sediment in the operating area the pump should be

placed on house bricks or similar.

• Ensure the pump is positioned with adequate space so that the

movement of the float switch is not restricted - recommended

minimum area of 40 x 40cm.

• ALWAYS raise and lower the pump using a rope attached to the

lifting handle.

• Take all necessary precautions as described on page 3 before

plugging in and switching ON.

2. Connect the mains plug to a high sensitivity residual current device (RCD)

which has a tripping current of less then 30mA.

3. Switch the mains power supply on.

• The pump incorporates a float switch which automatically switches

the pump ON when the water is above a pre-determined level.

• The pump will begin to drain water.

• As the water level falls, so will the float switch until it stops the pump.

4. Disconnect the pump from the mains power supply when finished.

• These pumps are fitted with automatic thermal overload protection.

If the pump overheats due to an obstruction in the pump or

pumping warm water for example, it will shut off automatically.

Switch the pump OFF and disconnect from the mains supply. Check

for blockages and allow the motor to cool (at least 5 minutes)

before attempting to re-start.

WARNING: CHECK THE PUMP FOR DAMAGE BEFORE USE. DO NOT USE THE

PUMP IF IT IS DAMAGED IN ANY WAY.

WARNING: THE WATER BEING PUMPED WILL BE POLLUTED IF THIS PUMP

BECOMES DAMAGED AND LUBRICANT WITHIN THE PUMP ESCAPES.

WARNING: NEVER CARRY THE PUMP USING THE MAINS POWER CABLE.

DAMAGE TO ELECTRICAL CABLES CAN BE HAZARDOUS. ALWAYS USE THE

HANDLE WHEN MOVING THE PUMP.

CAUTION: DO NOT ALLOW THE PUMP TO RUN DRY

MAINTENANCE

These pumps should require no maintenance other than regular cleaning.

If the pump starts to show signs of wear or damage, contact your CLARKE

dealer for advice.

Do not use the pump if there is any damage to the mains supply cable or to

the float switch or its cable.

Do not attempt to repair the pump yourself as you may damage the

waterproof seal and invalidate your guarantee. Repairs must be carried out

by your CLARKE dealer or contact the CLARKE Service Department on 020

8988 7400.

If the troubleshooting on page 8 does not solve your problem please contact

the Clarke service department.

CLEANING

1. Check the pump installation regularly to ensure the base inlet is clear of

leaves or other debris.

• These pumps have screwless fittings at

their base, allowing the removal of the

plastic cover by prising the two

release clips apart in the direction of

the arrows.

• This allows better access to the cavity

at the bottom, should the pump

become badly clogged. Flush the

cavity and the impeller housing with

clean water.

• To replace the cover, ensure the

release clips line up with the holes on the base of the pump and

press the cover home.

NOTE: Do not attempt to strip the pump further as this will invalidate the

guarantee.

WARNING: BEFORE CHECKING THE CONDITION OF THE PUMP, ENSURE IT

IS UNPLUGGED FROM THE MAINS SUPPLY.

TROUBLESHOOTING

PROBLEM SOLUTION

PUMP WILL

NOT START

1. Check to ensure power is switched on.

2. Check fuse (consult an electrician if in doubt).

3. If extension lead is fitted, check connections (consult an

electrician if in doubt).

4. Internal thermal cut-out has not re-set. Leave for 5

minutes and try again.

5. The impeller may be jammed. Disconnect from the mains

supply, remove the bottom strainer and remove any

objects that may be obstructing the impeller. Replace

the strainer and try again.

6. If the pump still fails to start consult your CLARKE dealer for

advice.

7. Floatswitch may be jammed against side wall or

prevented from moving.

8. Water level too low - float switch in OFF position - lift float

to check switch.

PUMP WILL

START BUT NOT

PUMP

1. Check to ensure strainer is not blocked.

2. Discharge tube clogged or obstructed.

3. The head may be too great, i.e. you are trying to lift the

water too great a distance for the pump to cope with.

(See specifications on page 2).

4. Air bubble in the pump, produced during the plunge.

Plunge the pump again at an angle and shake it whilst

lowering to remove any air trapped in the system.

5. Impeller may be damaged - Consult your CLARKE dealer.

PUMP WILL

NOT STOP

1. Float switch may be prevented from moving to the fully

down position.

2. Float switch may be faulty. Consult your CLARKE dealer

for advice.

PUMP STOPS

RUNNING

1. Thermal overload has operated. If this condition persists,

investigate the cause. Are you attempting to pump liquid

which is too heavy for the pump (mud, slurry etc.)

2. Pump has run dry or float switch has cut in.

3. A foreign object has jammed the impeller.

DECLARATION OF CONFORMITY

EXPLODED PARTS DIAGRAM - CSV1A/2A

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Bomba de agua de Clarke

Clarke

Clarke CGP870 Manual de instrucciones

Clarke

Clarke CPE20A1 Manual de instrucciones

Clarke

Clarke PSV3A Manual de instrucciones

Clarke

Clarke HSE120 Manual de instalación y operación

Clarke

Clarke GSE1 Manual de instrucciones

Clarke

Clarke CEB103 Manual de instrucciones

Clarke

Clarke TAM101 Manual de instalación y operación

Clarke

Clarke TAM100 7230035 Manual de instalación y operación

Clarke

Clarke PTP100 Manual de instrucciones

Clarke

Clarke ISP10A Manual de instalación y operación

Clarke

Clarke IVP14A Manual de instrucciones

Clarke

Clarke CU150 Manual de instalación y operación

Clarke

Clarke Hippo 2A Manual

Clarke

Clarke CPE15A1 Manual de instrucciones

Clarke

Clarke CFT230 Manual

Clarke

Clarke CSE400A Manual de instalación y operación

Clarke

Clarke SUBMERSIBLE PUMP Manual de instrucciones

Clarke

Clarke CVPS Guía rápida

Clarke

Clarke CWBP300 Manual de instrucciones

Clarke

Clarke CPRP560 Manual de instrucciones

Clarke

Clarke CPE30A1 Manual de instrucciones

Clarke

Clarke CHF2 Manual de instalación y operación

Clarke

Clarke STP12 Manual de instrucciones

Clarke

Clarke CHHDP830 Manual de instrucciones

Manuales populares de Bomba de agua de otras marcas

Neptun

Neptun NPHW 5500 Manual de usuario

Sensidyne

Sensidyne Gilian BDX-II Instrucciones de instalación y funcionamiento

Draper

Draper 47808 Manual de usuario

Trolla

Trolla 12820 Manual de usuario

Sunfab

Sunfab SVH Series Manual de usuario

WilTec

WilTec 50740 Manual de usuario

Fieldmann

Fieldmann FVC 5015 EK Manual de usuario

Everbilt

Everbilt EFSUB5-122HD Manual de usuario

Graco

Graco Husky 3300e Manual de usuario

esotec

esotec 101018 Manual de usuario

moyno

moyno 2000 CC Manual de usuario

Becker

Becker BASIC VASF 2.80/1-0.AC230 Manual de usuario

Sykes AmeriPumps

Sykes AmeriPumps GP100M Guía de solución de problemas

DUROMAX

DUROMAX XP WX Series Manual de usuario

BRINKMANN PUMPS

BRINKMANN PUMPS SBF550 Manual de usuario

Franklin Electric

Franklin Electric IPS Manual de usuario

Xylem

Xylem e-1532 Series Manual de usuario

Milton Roy

Milton Roy PRIMEROYAL Manual de usuario