Clarke CVPW Guía rápida

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

MODEL NO: CVPW

PART NO:

PART NO: 6499644

Weak Chemical Vane Pump

INTRODUCTION

Thank you for purchasing this CLARKE vane pump,

Suitable for use with weak corrosive chemicals such as weak acid, alkali and water based chemicals

Before attempting to use this product, please read this manual thoroughly and follow the instructions carefully.

SAFETY

To ensure safe and efficient operation, it is essential to read and follow each of these warnings and precautions.

1. When used to pump flammable liquids, improper use or installation of this product can cause serious bodily injury or

death.

2. Do NOT smoke near the pump or use the pump near an open flame. Fire could result.

3. When pumping flammable liquids, all equipment must be grounded to prevent the build up of static electricity

which may ignite vapours or gases.

SPECIFICATIONS

GUARANTEE

This product is guaranteed against faulty manufacture for a period of 12 months from the date of

purchase. Please keep your receipt which will be required as proof of purchase.

This guarantee is invalid if the product is found to have been abused or tampered with in any way, or not

used for the purpose for which it was intended.

Faulty goods should be returned to their place of purchase, no product can be returned to us without prior

permission.

This guarantee does not effect your statutory rights.

WARNING: THIS PRODUCT IS NOT SUITABLE FOR USE WITH FLUIDS FOR HUMAN CONSUMPTION OR AQUEOUS FLUIDS.

THIS PRODUCT SHOULD NOT BE USED FOR FLUID TRANSFER INTO AIRCRAFT.

Barrel Adaptor Size 2" BSP Outlet Tube Diameter 19 mm

Max Flow 0.35l per rotation Dims (WxDxH) 215 x 270 x 1325 mm

Inlet Tube Diameter 27 mm Product Weight 1.9 kg

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

ASSEMBLY

FITTING THE PUMP TO A BARREL

1. Assemble the pump using the required number of inlet tubes. Use the PTFE tape at all connections

• The tube which contains the black fiter + mesh should be at the bottom.

2. Screw the collar into the threaded opening of the barrel.

3. Raise or lower the inlet tube so that it is just off of the bottom of the barrel when fitted.

USING THE PUMP

1. Make sure all connections are secure and place a suitable container under the spout.

2. Rotate the handle to draw fluid from the barrel.

• The first time you use the pump, liquid should begin flowing after several turns of the handle

MAINTENANCE

CLEANING THE INLET FILTER

1. Unscrew the inlet filter from the bottom of the inlet tube and clear away any debris it has trapped.

2. Replace the filter.

WHAT IS SUPPLIED ASSEMBLED

CAUTION: DO NOT USE THE PUMP WITHOUT THE FILTER IN PLACE.

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

CHEMICAL RESISTANCE TABLE

• Room Temperature

•%SayMassConcentration

WATER ACIDS ALKALI PETROLEUM

BASED

HALOGENS ALCOHOL THINNER

Sea Water Acetic Acid

20%

Potassium

Hydroxide

25%

Silicone Oil Calcium

Chloride 10%

Ethanol 96% Acetone

Boric Acid

10%

Sodium

Hydroxide

solution 50%

Copper

Sulphate

Glycerine

Citric Acid

10%

Potassium

Dichromate

10%

Isopropanol

Hydraulic

Acid 35%

Soap Solution Methanol

Lactic Acid

80%

Sodium

Chloride 10%

Propanol

Nitric Acid

10%

Sodium

Nitrate 10%

Oxalic Acid

50%

Sodium

Thiosulphate

Phosphoric

Acid 50%

Zinc Chloride

10%

Sulphuric

Acid 70%

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

Este manual sirve para los siguientes modelos

Otros manuales de Bomba de agua de Clarke

Clarke

Clarke CPPRSS Manual de usuario

Clarke

Clarke CPE30A3 Manual de instrucciones

Clarke

Clarke ECP15A1 Manual de instrucciones

Clarke

Clarke CGP870 Manual de instrucciones

Clarke

Clarke CPE20A1 Manual de instrucciones

Clarke

Clarke DFT12 Manual de instrucciones

Clarke

Clarke CPE20A3 Manual de instrucciones

Clarke

Clarke PW50 Manual de instrucciones

Clarke

Clarke PW50A Manual de instrucciones

Clarke

Clarke CSE400A Manual de instrucciones

Clarke

Clarke CRWP1 Manual de usuario

Clarke

Clarke CDDFTP Manual de usuario

Clarke

Clarke HSE RANGE Manual de instrucciones

Clarke

Clarke CPE Series Manual de instrucciones

Clarke

Clarke CBM250SS Manual de instrucciones

Clarke

Clarke HSE Series Manual de instalación y operación

Clarke

Clarke CSP1530 Manual de instrucciones

Clarke

Clarke SPE800 Manual de instalación y operación

Clarke

Clarke PW2 Manual de instalación y operación

Clarke

Clarke psp125b Manual de instrucciones

Clarke

Clarke CM1 Manual de instalación y operación

Clarke

Clarke DWP300A Manual de instrucciones

Clarke

Clarke CVPS Guía rápida

Clarke

Clarke CHF2 Manual de instalación y operación

Manuales populares de Bomba de agua de otras marcas

Neptun

Neptun NPHW 5500 Manual de usuario

Sensidyne

Sensidyne Gilian BDX-II Instrucciones de instalación y funcionamiento

Draper

Draper 47808 Manual de usuario

Trolla

Trolla 12820 Manual de usuario

Sunfab

Sunfab SVH Series Manual de usuario

WilTec

WilTec 50740 Manual de usuario

Fieldmann

Fieldmann FVC 5015 EK Manual de usuario

Everbilt

Everbilt EFSUB5-122HD Manual de usuario

Graco

Graco Husky 3300e Manual de usuario

esotec

esotec 101018 Manual de usuario

moyno

moyno 2000 CC Manual de usuario

Becker

Becker BASIC VASF 2.80/1-0.AC230 Manual de usuario

Sykes AmeriPumps

Sykes AmeriPumps GP100M Guía de solución de problemas

DUROMAX

DUROMAX XP WX Series Manual de usuario

BRINKMANN PUMPS

BRINKMANN PUMPS SBF550 Manual de usuario

Franklin Electric

Franklin Electric IPS Manual de usuario

Xylem

Xylem e-1532 Series Manual de usuario

Milton Roy

Milton Roy PRIMEROYAL Manual de usuario