Clarke CWR45B Manual de programación

Este manual sirve para los siguientes modelos

1

Tabla de contenidos

Otros manuales de Rack y soporte de Clarke

Clarke

Clarke Strong-Arm CES680 Manual del propietario

Clarke

Clarke CBS3 Manual de usuario

Clarke

Clarke CES560 Manual de usuario

Clarke

Clarke CT100PR Manual de usuario

Clarke

Clarke CES680F Manual del propietario

Clarke

Clarke CAX3TBC Manual de usuario

Clarke

Clarke CDS3 Manual de usuario

Clarke

Clarke CARS1 Manual de instrucciones

Clarke

Clarke CWC80B Manual de usuario

Clarke

Clarke LB7S Manual de instrucciones

Clarke

Clarke CTA150 Manual de usuario

Clarke

Clarke CUTS1 Manual de usuario

Clarke

Clarke CMSS Manual de usuario

Clarke

Clarke LB5S Manual de instrucciones

Clarke

Clarke Strong-Arm CES340 Manual de usuario

Clarke

Clarke CWR1 Manual de usuario

Clarke

Clarke CAX3TA Manual de usuario

Clarke

Clarke CSM5175 Series Manual de usuario

Clarke

Clarke CRSF2 Manual de usuario

Clarke

Clarke STRONG-ARM CAX3TPB Manual de usuario

Clarke

Clarke CMS1 Manual de usuario

Clarke

Clarke CWR45 Manual de programación

Clarke

Clarke CSM4200 Manual de usuario

Clarke

Clarke CWMWR1 Manual de usuario

Manuales populares de Rack y soporte de otras marcas

Salamander

Salamander Acadia AC/W/L400/WH Manual de usuario

Fohhn

Fohhn VAT-09 Guía del usuario

ricoo

ricoo FS0522 Manual de usuario

AMSOIL

AMSOIL BMK-22 Guía rápida

Kargo Master

Kargo Master 48220 Manual de usuario

Milestone AV Technologies

Milestone AV Technologies SIMPLICITY SLF2 Manual de usuario

ricoo

ricoo S1222 Manual de usuario

Ready-Set-Mount

Ready-Set-Mount RSMCM602 Manual de usuario

VidaBox

VidaBox VB MNT FFS2 Manual de usuario

Welch Allyn

Welch Allyn 48960 Manual de usuario

Arkon

Arkon CM035-ST-2 Manual de usuario

PROEL

PROEL PLWIN60C Manual de usuario

Agilent Technologies

Agilent Technologies E2609B Manual de usuario

Mustang

Mustang MV-ARM4 Manual de usuario

Mounting Solutions

Mounting Solutions WRM-320 Manual de usuario

Pyle

Pyle PMKSPAD1 Manual de usuario

ShelterIt

ShelterIt 21208 Manual de usuario

SPL

SPL RackPack?4 1040 Manual de usuario

ASSEMBLY & INSTALLATION

INSTRUCTIONS GC07/12

WALL MOUNTED TOOL RACK

Model CWR45B

Part No: 4800200

2

Parts & Service: 020 8988 7400/E-mail:[email protected] or [email protected]

INTRODUCTION

Thank you for purchasing this CLARKE wall rack. Please follow these assembly

instructions carefully.

GUARANTEE

This CLARKE product is guaranteed against faulty manufacture for a period of

12 months from the date of purchase. Please keep your receipt as proof of

purchase.

This guarantee is invalid if the product is found to have been abused or

tampered with in any way, or not used for the purpose for which it was

intended. Faulty goods should be returned to their place of purchase, no

product can be returned to us without prior permission.

This guarantee does not effect your statutory rights.

ENVIRONMENTAL PROTECTION

Do not dispose of workshop products with general household waste. All tools,

accessories and packaging should be sorted, taken to a re-cycling centre

and disposed of appropriately.

TECHNICAL DATA

• Dimensions (mm) 1115 long x 15 deep x 635 high

• Weight 6.2 kg

3

Parts & Service: 020 8988 7400/E-mail:Part[email protected] or [email protected]

PARTS LIST

Unpack your wall rack and check to ensure that no damage was suffered

during transit. Should any damage be apparent, you should contact your

Clarke dealer immediately.

The kit comprises: 5 x panels

10 x assorted tool holders

8 x sets of bolts & nuts

2 screws with rawlplugs

Tools required: Power drill with masonry drill bits

X-head screwdriver

6mm spanner/ flat screwdriver

ASSEMBLY

1. Fix the five panels together, side by side, using the nuts and bolts supplied.

Ensure that the panels with the wall fixing brackets are at each end of the

assembly. Use two bolts per panel joint. Fully tighten all the nuts.

2. Mark the intended position of the product on the wall. Accurately

measure the distance between the centres of the holes of the integral

supporting brackets on the back of the end panels.

• End panels only are used for fixing.

3. Mark these hole centres on the wall and drill holes for the rawlplugs

supplied. Secure the screws into each fixing position.

4. The wall rack can now be hung on these screws, ensuring the head of

each screw fully locates into the supporting bracket on the back of each

end panel.

5. After securing the wall rack to the wall, attach the tool holders in the

desired positions to suit your tools.

x x x x

x x x x

Wall fixings

here

Connecting

bolts here