Clarke CWC80B Manual de usuario

ASSEMBLY INSTRUCTIONS

GC07/12

Wall Storage Rack & Cabinet

Model: CWC80B

Part No: 4800265

Parts & Service: 020 8988 7400/E-mail:[email protected] or [email protected]

PRE-ASSEMBLY CHECK

Unpack the components and lay them out carefully. Referring to the parts list

ensuring that all parts are present. If there are any deficiencies, immediately

contact the dealer from where the product was purchased, or the Clarke

International Parts Department on 020 8988 7400.

ASSEMBLY

NOTES: When assembling, all screw heads should be on the outside of the

cabinet. DO NOT tighten any nuts until the cabinet is fully assembled.

Make a note of the position of the wall mounting holes in each back

panel. These must be uppermost when the cabinet is assembled.

1. Take the back panels as shown in Fig 1, with the central side panel (with

shelf brackets) positioned between them as shown.

NOTE: The central side panel includes brackets to support the shelves and

must therefore face the end panel with the corresponding shelf brackets.

2. Line up the holes and connect with a screw & nut at each location.

3. Place the top panel on to the back panel assembly as shown in Fig 2, so

that the edge with the return fold lies at the front and connect all parts

loosely together.

4. Offer up the other side panel with shelf brackets to one end so that the

shelf brackets match those at the centre of the unit. Line up the corner

holes at ‘A’, and secure with a screw/nut.

5. Repeat at the front corners. Repeat the process with the other side panel.

FIG 1

Mounting Holes

Parts & Service: 020 8988 7400/E-mail:Part[email protected] or [email protected]

6. Lay the assembly down, as shown in Fig 3 and offer up the bottom panel

(the edge with the return fold uppermost).

7. Line up the holes in each corner at B and loosely insert a screw & nut.

8. Attach the door by inserting the pivot pins into the pivot holes in the top

and bottom panels. Line up the holes at C, insert a screw and with the

door open, fit a nut at each corner.

9. With the cabinet lying on a flat surface, as in Fig 3, rock it gently to ensure

that no part is unduly stressed, before tightening all the screws/nuts

progressively.

10. Attach the wall hanging brackets to the back panels using the screws and

nuts provided.

Your wall cabinet is now ready to hang. Ensure it is firmly attached to the wall

before loading with tools. Wall plugs and screws are provided for the purpose.

The shelves are rested on the supporting brackets, while the tool holders

engage with the back panel, and may be positioned to your own choice.

FIG 2

FIG 3 Pivot Hole

Pivot Hole

GUARANTEE

This CLARKE product is guaranteed against faulty manufacture for a period of

12 months from the date of purchase. Please keep your receipt as proof of

purchase. This guarantee is invalid if the product is found to have been

abused or tampered with in any way, or not used for its intended purpose.

Faulty goods should be returned to their place of purchase, no product can

be returned to us without prior permission. This guarantee does not effect

your statutory rights.

oN noitpircseD ytQ noitpircseD ytQ

1lenaPmottoB/poT2gulPllaW2

2stekcarbflehshtiwlenaPediS2wercSgnitnuoM2

3lenaPediSnialP101x5MwercS81

4lenaPkcaBdetarofr

eP15MtuN81

5lenaPkcaBnialP1sredloHlooTelgniS5

6stekcarBgnignaHllaW2redloHhcnerW1

7rooDtnorF1redloHrevirdwercS1

8yekhtiwys

sAkcoLrooD1redloHeliF1

9flehS3

PART LIST & DIAGRAM

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Rack y soporte de Clarke

Clarke

Clarke CTA150 Manual de usuario

Clarke

Clarke CMSS Manual de usuario

Clarke

Clarke CGR1 Manual de usuario

Clarke

Clarke LB7S Manual de instrucciones

Clarke

Clarke CSM4200 Manual de usuario

Clarke

Clarke STRONG-ARM CAX3TPB Manual de usuario

Clarke

Clarke CMS1 Manual de usuario

Clarke

Clarke CT100PR Manual de usuario

Clarke

Clarke CAX3TAB Manual de usuario

Clarke

Clarke CUTS1 Manual de usuario

Clarke

Clarke CSR4550BO Manual de usuario

Clarke

Clarke Strong-Arm CES340 Manual de usuario

Clarke

Clarke LB5S Manual de instrucciones

Clarke

Clarke CAX20S Manual de usuario

Clarke

Clarke CWR45 Manual de programación

Clarke

Clarke CSP420 Manual de usuario

Clarke

Clarke CARS1 Manual de instrucciones

Clarke

Clarke MCD1 Manual de instrucciones

Clarke

Clarke CAX3TA Manual de usuario

Clarke

Clarke CMSSR Manual de usuario

Clarke

Clarke CWR1 Manual de usuario

Clarke

Clarke CRSF2 Manual de usuario

Clarke

Clarke CBS3 Manual de usuario

Clarke

Clarke MDS1 Manual de usuario

Manuales populares de Rack y soporte de otras marcas

Salamander

Salamander Acadia AC/W/L400/WH Manual de usuario

Fohhn

Fohhn VAT-09 Guía del usuario

ricoo

ricoo FS0522 Manual de usuario

AMSOIL

AMSOIL BMK-22 Guía rápida

Kargo Master

Kargo Master 48220 Manual de usuario

Milestone AV Technologies

Milestone AV Technologies SIMPLICITY SLF2 Manual de usuario

ricoo

ricoo S1222 Manual de usuario

Ready-Set-Mount

Ready-Set-Mount RSMCM602 Manual de usuario

VidaBox

VidaBox VB MNT FFS2 Manual de usuario

Welch Allyn

Welch Allyn 48960 Manual de usuario

Arkon

Arkon CM035-ST-2 Manual de usuario

PROEL

PROEL PLWIN60C Manual de usuario

Agilent Technologies

Agilent Technologies E2609B Manual de usuario

Mustang

Mustang MV-ARM4 Manual de usuario

Mounting Solutions

Mounting Solutions WRM-320 Manual de usuario

Pyle

Pyle PMKSPAD1 Manual de usuario

ShelterIt

ShelterIt 21208 Manual de usuario

SPL

SPL RackPack?4 1040 Manual de usuario