Cisco WAP121 Manual de usuario

Reboot and Factory Default Reset on

WAP121 and WAP321 Access Points

Objective

This article explains how to perform a standard reboot and also how to reset to factory

default on the WAP121 and WAP321 access points. Reboot or restart of the network

device is made when certain changes in the settings need a reboot or if the device is

frozen. Consequences of reboot will result in the deletion of logs in volatile memory.

The configuration settings of the network device gets reflected after the restart. Factory

default reset is used to remove the running/current configuration settings on the

network device and to restore it to the original default settings. Factory default reset is

recommended when the whole device needed to be reconfigured and also in case if

you forget the password and not able to recover by any means such as telnet.

Applicable Devices | Firmware Version

WAP121 | 1.0.3.4 (Download latest)

●

WAP321 | 1.0.3.4 (Download latest)

●

Reset to Factory Default

There are two ways to reset to factory default settings to the factory default

configuration:

Hardware Reset

●

Factory default reset by web configuration utility

●

Hardware Reset

Step 1. Hold the Reset button located at the back of the device for approximately ten

seconds with a pin.

The Access Point reloads and is set to the default configuration settings.

Step 2. Launch a web browser, such as Internet Explorer or Mozilla Firefox. Type the

default static IP address 192.168.1.245 in the URL bar and press enter. To reach that

IP address, be sure that your computer is on the 192.168.1.xxx network.

If your network has a DHCP server, then the factory default IP address configuration of the

WAP is DHCP. In the absence of a DHCP server, the access point will fallback to the

default static IP address after 60 seconds.

Step 3. Login with the default credentials.The default username is cisco, and the

default password is cisco.

Factory Default Reset by Web Configuration Utility

Step 1. Log in to the web configuration utility and choose Administration > Reboot.

The Reboot page opens:

Step 2. Click Reboot To Factory Default to reboot the access point and return the

device to factory default settings. Once rebooted to factory default, all saved

configurations will be lost.

Step 3. The Confirm window appears. Click OK to continue with the reboot to factory

default settings.

Reboot Access Point

There are two ways to reset the Access Point:

• Hardware reset

• Reset with the use of the web configuration utility

Reboot Access Point by Hardware

Step 1. Press the power button to turn off the device. After 10 seconds have passed,

press the power button a second time to power the device back on.

The Access Point reboots and is refreshed.

Reboot Access Point by Web Configuration Utility

Step 1. Log in to the web configuration utility and choose Administration > Reboot.

The Reboot page opens:

Step 2. Click Reboot to reboot the device.

Step 3. The confirm window appears. Click OK to continue with the reboot of the

device.

If you would like to read an article on this same topic, check out Reboot and Reset the

Wireless Access Point to Factory Default Settings.

Otros manuales para WAP121

9

Este manual sirve para los siguientes modelos

1

Tabla de contenidos

Otros manuales de Punto de acceso inalámbrico de Cisco

Cisco

Cisco Aironet 1800i Manual de usuario

Cisco

Cisco WAP571E Manual de usuario

Cisco

Cisco 700 series Manual de usuario

Cisco

Cisco Meraki MR36 Manual de usuario

Cisco

Cisco Small Business WAP44 Manual de instrucciones

Cisco

Cisco Small Business WAP551 Manual de instrucciones

Cisco

Cisco WAP4410N - Small Business Wireless-N Access... Manual de usuario

Cisco

Cisco 1130AG - Aironet - Wireless Access Point Manual

Cisco

Cisco ASA 5506W-X Manual de usuario

Cisco

Cisco Meraki MR76 Manual de usuario

Cisco

Cisco Aironet 3500 Series Manual de usuario

Cisco

Cisco Meraki MR56 Manual de usuario

Cisco

Cisco Aironet 700W Series Manual de usuario

Cisco

Cisco Meraki MR42E Manual de usuario

Cisco

Cisco WAP121 Manual de usuario

Cisco

Cisco MERAKI MR44 Manual de usuario

Cisco

Cisco 1130AG - Aironet - Wireless Access Point Manual

Cisco

Cisco AT&T U-VERSE VEN401 Manual de usuario

Cisco

Cisco Aironet 1810W Series Manual de usuario

Cisco

Cisco Aironet 1240AG Series Manual

Cisco

Cisco Aironet 1550 Series Manual de usuario

Cisco

Cisco 1830 Series Manual de usuario

Cisco

Cisco M10-RM Guía de inicio rápido

Cisco

Cisco AIR-AP1542I-*-K Manual de usuario

Manuales populares de Punto de acceso inalámbrico de otras marcas

D-Link

D-Link DWL-2100AP - AirPlus Xtreme G Manual de usuario

Ubiquiti

Ubiquiti NanoStation NSM2 Manual de usuario

Aruba

Aruba IAP-335 Manual de usuario

Advantek Networks

Advantek Networks AWN-AP-54MR Manual de usuario

IP-COM

IP-COM AP355 Manual de usuario

Buffalo

Buffalo AirStation WLA-L11G Manual de usuario

EnGenius

EnGenius EnStationACv2 Manual de usuario

D-Link

D-Link DAP-3662 Manual de usuario

xG Technology

xG Technology xMax CN1300 Manual de usuario

Widelink

Widelink ezWave WAP-1100 Series Manual de usuario

Edimax

Edimax CAP1200 Manual de usuario

Ubiquiti

Ubiquiti LBE-5AC-Gen2 Manual de usuario

Aruba

Aruba AP-203R Manual de usuario

LuXout Shades

LuXout Shades LUXSHADE MOTION Manual de usuario

CreatComm

CreatComm TB5F Manual de usuario

SineDigital

SineDigital MW-1500AP(H) Manual de usuario

TP-Link

TP-Link AP9650 V1 Manual de usuario

Draytek

Draytek VIGORAP 902 Manual de usuario