Cisco 12010 series Manual de usuario

CHAPTER

7-1

Cisco 12010, Cisco 12410, and Cisco 12810 Router Installation and Configuration Guide

OL-11496-01

Maintaining the Router

Your router is equipped as ordered and is ready for installation and startup when

it is shipped. As your networking requirements change, you may need to upgrade

the system by adding or changing components. This chapter describes how to

maintain router components.

Procedures for maintaining the router are described in the following sections:

•Powering Off the Router, page 7-2

•Removing and Installing the Front Covers and Bezel Extenders on Original

Cisco 12010 Series Routers, page 7-3

•Removing and Installing the Front Door on Cisco 12010 Enhanced Series

Router, page 7-11

•Cleaning or Replacing the Chassis Air Filter, page 7-16

•Removing and Replacing the Blower Module, page 7-23

•Removing and Replacing AC and DC Power Subsystem Components,

page 7-27

•Removing and Replacing Cards from the Chassis, page 7-61

•Upgrading the Switch Fabric in the Cisco 12410 Router, page 7-67

•Removing and Installing a Chassis, page 7-69

Chapter 7 Maintaining the Router

Powering Off the Router

7-2

Cisco 12010, Cisco 12410, and Cisco 12810 Router Installation and Configuration Guide

OL-11496-01

Prerequisites and Preparation

Before you perform any of the procedures in this chapter, be sure that you:

•Review the “Safety Guidelines” section on page 2-2.

•Read the safety and ESD-prevention guidelines described in the “Compliance

and Safety Information” section on page 2-3.

•Ensure that you have all of the necessary tools and equipment before

beginning the procedure.

•Have access to the following documents during the installation:

–

Regulatory Compliance and Safety Information for Cisco 12000 Series

Routers publication that shipped with the router (PN 78-4347-xx)

Powering Off the Router

Most Cisco 12010, Cisco 12410, and Cisco 12810 series routers field-replaceable

units (FRUs) can be removed and replaced with the power on and the system

operating. This is known as online insertion and removal (OIR). Power supplies,

line cards, the RP, CSCs, SFCs, and alarm cards all support OIR. Unless otherwise

noted, the maintenance tasks described in this chapter can be performed while the

router remains powered on.

In some cases it may be necessary to power off the router, for example, to upgrade

both power supplies and PDUs. Use the following procedure to power off the

router.

Step 1 Set the power switch on each power supply to the off (0) position.

Step 2 Power off all circuit breakers for the source power lines connected to the power

supplies.

Step 3 Verify that the Pwr OK indicator on each power supply is off.

Step 4 Verify that the OK indicator on the blower module is off.

7-3

Cisco 12010, Cisco 12410, and Cisco 12810 Router Installation and Configuration Guide

OL-11496-01

Chapter 7 Maintaining the Router

Removing and Installing the Front Covers and Bezel Extenders on Original Cisco 12010 Series Routers

Removing and Installing the Front Covers and Bezel

Extenders on Original Cisco 12010 Series Routers

The front covers are fastened to the chassis by ball studs that insert into clips on

the front of the chassis. The front covers are referred to as snap-on front covers.

The partial front cover on the air filter door is fastened to the air filter door by four

screws inserted from the back side of the air filter door. This partial front cover is

referred to as the air filter door front cover.

Note Recently released routers have bezel extenders installed on the front cover (bezel)

for the line card and route processor (RP) card cage to bring the cover out an

additional 2 inches (50.8 mm) to allow more room for cables. If your chassis does

not have these extenders and you want to purchase them, contact Cisco sales. (See

the “Attaching Bezel Extenders to the Front Cover” section on page 7-6 if you are

installing the bezel extenders.)

Removing the Front Covers

The front covers are held in place by ball studs that snap into clips on the chassis.

Refer to Figure 7-1 and use the following procedure to remove the snap-on front

covers.

Step 1 Grasp the outside edges of the blower module front cover and pull it straight out

to detach the front cover from the chassis.

Step 2 Repeat Step 1 for the RP and line card cage front cover.

Chapter 7 Maintaining the Router

Removing and Installing the Front Covers and Bezel Extenders on Original Cisco 12010 Series Routers

7-4

Cisco 12010, Cisco 12410, and Cisco 12810 Router Installation and Configuration Guide

OL-11496-01

Installing the Front Covers

Refer to Figure 7-1 and use the following procedure to install the front covers.

Step 1 Hold the front cover by its outside edges and align the ball studs with the ball stud

clips on the front of the chassis.

Step 2 Push the front cover into the ball stud clips and the front cover is flush with the

front of the chassis.

Step 3 Repeat Step 1 and Step 2 for the remaining front cover.

7-5

Cisco 12010, Cisco 12410, and Cisco 12810 Router Installation and Configuration Guide

OL-11496-01

Chapter 7 Maintaining the Router

Removing and Installing the Front Covers and Bezel Extenders on Original Cisco 12010 Series Routers

Figure 7-1 Removing and Installing the Front Covers

Chapter 7 Maintaining the Router

Removing and Installing the Front Covers and Bezel Extenders on Original Cisco 12010 Series Routers

7-6

Cisco 12010, Cisco 12410, and Cisco 12810 Router Installation and Configuration Guide

OL-11496-01

Attaching Bezel Extenders to the Front Cover

Use the following procedure to attach the bezel extenders to the card cage front

cover.

Step 1 Remove the line card and RP card cage front cover from the chassis as described

in the “Removing the Front Covers” section on page 7-3.

Step 2 Remove the four ball studs from the front cover (Figure 7-2, item 3).

Step 3 Screw the four ball studs into the threaded holes on the bezel extenders (two ball

studs for each bezel extender) using a wrench to secure them.

Caution Do not overtighten the ball studs. Overtightening the ball studs could damage the

threaded hole on the bezel extender.

Step 4 Attach the bezel extenders to the front cover:

a. Facing the inside of the front cover, align the screw holes in the left side bezel

extender with the mounting screw holes in the front cover (Figure 7-2,

item 4).

Note If you cannot align both screw holes on the front cover inserts, you have

the incorrect bezel extender. Try the other bezel extender on this side.

b. Fasten the bezel extender to the front cover with the mounting screws

(Figure 7-2, item 2).

Caution Do not overtighten the screws. Overtightening the screws could damage the

threaded holes in the front cover.

c. Repeat Steps aand bto fasten the right side bezel extender to the other side

of the front cover (Figure 7-2, item 5).

7-7

Cisco 12010, Cisco 12410, and Cisco 12810 Router Installation and Configuration Guide

OL-11496-01

Chapter 7 Maintaining the Router

Removing and Installing the Front Covers and Bezel Extenders on Original Cisco 12010 Series Routers

Figure 7-2 Attaching the Bezel Extenders to the Front Cover

1Line card and RP card cage front cover (bezel) 4Left side bezel extender

2Mounting screws 5Right side bezel extender

3Ball studs ––

Chapter 7 Maintaining the Router

Removing and Installing the Front Covers and Bezel Extenders on Original Cisco 12010 Series Routers

7-8

Cisco 12010, Cisco 12410, and Cisco 12810 Router Installation and Configuration Guide

OL-11496-01

Step 5 Hold the front cover by its outside edges and align the ball studs with the ball stud

clips on the front of the chassis (Figure 7-3).

Figure 7-3 Attaching the Front Cover Using Bezel Extenders

Step 6 Push the front cover into the ball stud clips so that the front cover is flush with the

front of the chassis.

7-9

Cisco 12010, Cisco 12410, and Cisco 12810 Router Installation and Configuration Guide

OL-11496-01

Chapter 7 Maintaining the Router

Removing and Installing the Front Covers and Bezel Extenders on Original Cisco 12010 Series Routers

Removing and Replacing the Air Filter Door Front Cover

Use the following procedure to remove and replace the air filter door front cover.

Step 1 Loosen the captive screws on each side of the air filter door and swing the door

away from the switch fabric and alarm card cage.

Figure 7-4 Opening the Air Filter Door

Caution Be especially careful not to damage the honeycomb screen on the back of the air

filter door and on the inside of the switch fabric and alarm card cage. Damaging

the honeycomb screen can restrict the air flow and cause overheating and diminish

EMI protection.

Chapter 7 Maintaining the Router

Removing and Installing the Front Covers and Bezel Extenders on Original Cisco 12010 Series Routers

7-10

Cisco 12010, Cisco 12410, and Cisco 12810 Router Installation and Configuration Guide

OL-11496-01

Step 2 Remove the (4) screws from each corner that fasten the partial front cover to the

air filter door (Figure 7-5).

•Set aside the screws; you will need them to install the replacement front

cover.

Figure 7-5 Removing the Air Filter Door Front Cover

Step 3 Hold the replacement front cover by its outside edges and align the screw holes in

the front cover with the holes on the air filter door.

Step 4 Secure the front cover to the air filter door using the (4) screws that you removed

in Step 2.

Caution Do not overtighten the screws. Overtightening the screws can damage the

threaded holes in the air filter door.

Step 5 Close the air filter door and tighten the captive screws.

Caution Align and seat the door carefully to avoid damaging the EMI-preventive gaskets

on the door. The air filter door must be closed and secured at all times to maintain

correct EMI performance.

Otros manuales para 12010 series

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Enrutador de red de Cisco

Cisco

Cisco 7301 SDRAM Manual de usuario

Cisco

Cisco RV345 Manual de instrucciones

Cisco

Cisco CRS Manual de usuario

Cisco

Cisco 8800 Series Manual

Cisco

Cisco 1401 Manual de usuario

Cisco

Cisco IE 2000U Series Instrucciones de funcionamiento y seguridad

Cisco

Cisco 1921-T1SEC/K9 Manual de usuario

Cisco

Cisco 7609-S Manual de usuario

Cisco

Cisco 7600 Series Manual de usuario

Cisco

Cisco 12000 - Series Chassis Modular Expansion... Manual de usuario

Cisco

Cisco 880 Series Manual de usuario

Cisco

Cisco Linksys RV042 Manual de usuario

Cisco

Cisco Cisco 12416 Manual del operador

Cisco

Cisco 1840 Instrucciones originales

Cisco

Cisco 12016 Manual de usuario

Cisco

Cisco uBR924 Manual de usuario

Cisco

Cisco WRT350N Manual de usuario

Cisco

Cisco vEdge 100 Manual

Cisco

Cisco ASR-920-12SZ-IM Manual de usuario

Cisco

Cisco 7100 Series Manual de usuario

Cisco

Cisco WS-C1924-A - Catalyst 1900 24 Ports 10MB... Manual

Cisco

Cisco Linksys BEFVP41 v2 Manual de usuario

Cisco

Cisco 800 Series Manual

Cisco

Cisco SOHO 91 Manual de usuario

Manuales populares de Enrutador de red de otras marcas

Allnet

Allnet ALL0333AU Manual de usuario

HomeSeer

HomeSeer HT-SEL Manual de usuario

Sercomm

Sercomm Genesis OC3505D Manual de usuario

Billion

Billion BIPAC 5102 Series Manual de usuario

TP-Link

TP-Link TD-8817 Manual de usuario

Motorola

Motorola MR1900 Manual de usuario

Digi

Digi IX14 Manual de usuario

XAVi

XAVi X8821e Manual de usuario

BEC

BEC 6200WZL Manual de usuario

MikroTik

MikroTik hAP ac3 Series Manual de usuario

Korenix

Korenix JetNet 5428G Series Manual de usuario

NETGEAR

NETGEAR FS526T - Switch Manual de usuario

Korenix

Korenix JetNet 5710G Series Manual de usuario

Automated Logic

Automated Logic ZN551 Manual del propietario

EnGenius

EnGenius ESR-9710 Manual de usuario

LevelOne

LevelOne FBR-1416 Manual de usuario

Dynacord

Dynacord Promatrix 6000 Manual de usuario

Lorex

Lorex F5D8230-4 Manual de usuario