Cisco NCS 4216 Manual de instrucciones

Installing the Cisco NCS 4216

This chapter describes how to install the Cisco NCS 4216.

•Prerequisites, on page 1

•Installing the Router in a Rack, on page 1

•Installing the Chassis Ground Connection, on page 17

•Installing the Fan Tray, on page 19

•RSP Installation, on page 26

•Interface Module Installation, on page 29

•Installing the Power Supply, on page 33

•Installing the AC power Supply, on page 39

•Connecting the Cisco NCS 4216 Router to the Network, on page 42

Prerequisites

Before installing the Cisco NCS 4216, it is important to prepare for the installation by:

• Preparing the site (site planning) and reviewing the installation plans or method of procedures (MOP)

• Unpacking and inspecting the Cisco NCS 4216

• Gathering the tools and test equipment required to properly install the Cisco NCS 4216

For more instructions on how to prepare for the installation of the Cisco NCS 4216, see the Preparing for

Installation section.

Installing the Router in a Rack

The sections describe how to install the Cisco NCS 4216 in a rack.

The Cisco NCS 4216 Door is not displayed in the figures below. It is only displayed in the Installing the Cisco

NCS 4216 Door figure.

Note

Installing the Cisco NCS 4216

Installing the Chassis Brackets

The chassis is shipped with mounting brackets that can be installed on the front or rear of the chassis. To

install the brackets on the front of the chassis, perform these steps:

Procedure

Step 1 Remove the rack-mount brackets from the accessory kit and position them beside the router chassis.

Figure 1: Attaching Mounting Brackets for a 23-inch Rack

Step 2 Position one of the brackets against the chassis side, and align the screw holes.

Step 3 Secure the bracket to the chassis with the screws removed when performing Step 1. The recommended

maximum torque is 28 in.-lb (3.16 N-m).

The A907-FAN-E fan tray with filter (A907-FAN-F) cannot be mounted using the mounting screws that are

supported for fan tray. This is not an issue with the FAN tray filter blank panel (A907-FAN-F-B). We

recommend that you use the short screws provided in the following rack mount kits to avoid interference of

the air filter during rack mounting and while replacing the fan tray with the fan tray filter (A907-FAN-E):

• 23" rack mount kit (A907-RCKMT-23IN)

What to do next

Repeat Step 2 and Step 3 for the other bracket.

Installing the Cisco NCS 4216

Installing the Chassis Brackets

Installing Plenum Assembly and Chassis in the Rack

Following steps help you to install the plenum assembly irrespective of the chassis and rack size.

The below illustrations are for representation purpose only. The size displayed in the images may vary

depending upon your chassis type and rack size but the steps remain the same. Ensure to select the 21 or 23

inches adapter for your plenum based on your rack size.

Note

Procedure

Step 1 Position the adapter to the plenum base and secure using a maximum torque of 11.5 in.-lb (1.3 N-m). See

figure below.

Figure 2: Adapter to Plenum

Plenum2Plenum adapter deflector1

-Securing the Plenum to the base3

Step 2 Position the air deflector inside the plenum and secure using a maximum torque of 11.5 in.-lb (1.3 N-m). See

figure below.

Installing the Cisco NCS 4216

Installing Plenum Assembly and Chassis in the Rack

Figure 3: Deflector in Plenum

Plenum2Air deflector1

Step 3 Secure the plenum deflector with a recommended torque of 11.5 in.-lb (1.3 N-m). See figure below.

Figure 4: Plenum Deflector

Securing screws onto plenum2Secure deflector to plenum base1

Installing the Cisco NCS 4216

Installing Plenum Assembly and Chassis in the Rack

Step 4 Position the air baffle and the side plate to the plenum. Secure the air baffle and the side plate using a maximum

torque of 11.5 in.-lb (1.3 N-m). See figure below.

Figure 5: Assembling Air Baffle to the Plenum

Side plate2Air baffle1

Plenum deflector4Plenum base3

Step 5 Secure the air baffle using a maximum torque of 11.5 in.-lb (1.3 N-m). See figure below.

Installing the Cisco NCS 4216

Installing Plenum Assembly and Chassis in the Rack

Figure 6: Securing the Air Baffle Tray

-Securing air baffle to air plenum1

Step 6 Repeat Step-3 to Step-5 to complete the plenum assembly on the other side of the plenum base.

Step 7 Position the front cover hinge assembly on the plenum deflector. Secure the front cover using a recommended

torque of 11.5 in.-lb (1.3 N-m). See figure below.

Figure 7: Front Cover Hinge Assembly on the Plenum

-Front cover hinge assembly1

Installing the Cisco NCS 4216

Installing Plenum Assembly and Chassis in the Rack

Step 8 Secure the cable brackets to the plenum deflector using a torque of 11.5 in.-lb (1.3 N-m). See figure below.

Figure 8: Cable Brackets to Plenum Deflector

Screws to secure brackets2Cable brackets1

Step 9 Position the plenum assembly to the rack and secure the cable brackets to the rack using a torque of 11.5 in.-lb

(1.3 N-m). See figure below.

Installing the Cisco NCS 4216

Installing Plenum Assembly and Chassis in the Rack

Figure 9: Plenum Assembly to Rack

Plenum assembly2Rack1

-Securing the plenum to the brackets3

Step 10 Position cable guides on the router chassis.

Step 11 Guide the router chassis carefully into the plenum assembly. See figure below.

Installing the Cisco NCS 4216

Installing Plenum Assembly and Chassis in the Rack

Figure 10: Chassis Assembly to Plenum in Rack

Cable guides on chassis2Plenum assembly1

-Securing screws to chassis onto rack3

Step 12 Position the door onto the router chassis and slide it into the rack. Secure the screws with a torque of 11.5

in.-lb (1.3 N-m). See figure below.

Installing the Cisco NCS 4216

Installing Plenum Assembly and Chassis in the Rack

Figure 11: Door Assembly to Rack

Door2Chassis in plenum assembly1

-Securing door to the chassis onto rack3

Installing the Air Plenum (A907-F2B-AIR) in the Rack

This procedure installs the air plenum to orient the air flow in front-to- back direction in the NCS 4216 router.

Before performing any of the following procedures, ensure that power is removed from the DC circuit.

Statement 1074

Warning

This equipment is intended to be grounded. Ensure that the host is connected to earth ground during normal

use. Statement 39

Warning

For nominal voltage of -60 VDC, the input voltage range is from -40 to -72 VDC.

Note

Installing the Cisco NCS 4216

Installing the Air Plenum (A907-F2B-AIR) in the Rack

Otros manuales para NCS 4216

Tabla de contenidos

Otros manuales de Enrutador de red de Cisco

Cisco

Cisco CRS-1 - Carrier Routing System Router Manual de usuario

Cisco

Cisco ASR 9901 Manual

Cisco

Cisco ASR 5000 Series Instrucciones de funcionamiento y seguridad

Cisco

Cisco Profile Series Manual de usuario

Cisco

Cisco 10720 Series Manual del operador

Cisco

Cisco 828 Manual de usuario

Cisco

Cisco 2811 Series Manual de instrucciones

Cisco

Cisco 7600 Series Manual de usuario

Cisco

Cisco 1905 Manual de instrucciones

Cisco

Cisco ASR 5000 Series Manual de instrucciones

Cisco

Cisco RV130 Manual de usuario

Cisco

Cisco MWR 2941 Manual de funcionamiento

Cisco

Cisco 8800 Series Manual

Cisco

Cisco Universal Broadband Router uBR7200 Manual

Cisco

Cisco 1805 Manual de usuario

Cisco

Cisco CRM3 Manual de instrucciones

Cisco

Cisco XR 12404 Manual de usuario

Cisco

Cisco ASR1000-RP1 - ASR 1000 Series Route Processor 1... Manual de usuario

Cisco

Cisco Cisco 12416 Manual del operador

Cisco

Cisco WRT300N Manual de usuario

Cisco

Cisco ME 4924-10GE Instrucciones originales

Cisco

Cisco ASR 914 Manual de usuario

Cisco

Cisco 910 Manual de usuario

Cisco

Cisco SCE 1000 2xGBE Manual del operador

Manuales populares de Enrutador de red de otras marcas

Allnet

Allnet ALL0333AU Manual de usuario

HomeSeer

HomeSeer HT-SEL Manual de usuario

Sercomm

Sercomm Genesis OC3505D Manual de usuario

Billion

Billion BIPAC 5102 Series Manual de usuario

TP-Link

TP-Link TD-8817 Manual de usuario

Motorola

Motorola MR1900 Manual de usuario

Digi

Digi IX14 Manual de usuario

XAVi

XAVi X8821e Manual de usuario

BEC

BEC 6200WZL Manual de usuario

MikroTik

MikroTik hAP ac3 Series Manual de usuario

Korenix

Korenix JetNet 5428G Series Manual de usuario

NETGEAR

NETGEAR FS526T - Switch Manual de usuario

Korenix

Korenix JetNet 5710G Series Manual de usuario

Automated Logic

Automated Logic ZN551 Manual del propietario

EnGenius

EnGenius ESR-9710 Manual de usuario

LevelOne

LevelOne FBR-1416 Manual de usuario

Dynacord

Dynacord Promatrix 6000 Manual de usuario

Lorex

Lorex F5D8230-4 Manual de usuario