Cisco NCS 540 Series Manual de usuario

ARP Commands

All commands applicable for the Cisco NCS 5500 Series Router are also supported on the Cisco NCS 540

Series Router that is introduced from Cisco IOS XR Release 6.3.2. References to earlier releases in Command

History tables apply to only the Cisco NCS 5500 Series Router.

Note

This chapter describes the commands used to configure and monitor the Address Resolution Protocol (ARP)

on NCS 5000 routers.

For detailed information about ARP concepts, configuration tasks, and examples, refer to the IP Addresses

and Services Configuration Guide for Cisco NCS 5500 Series Routers.

•arp, on page 1

•arp gratuitous ignore, on page 3

•arp learning, on page 3

•arp purge-delay, on page 4

•arp timeout, on page 5

•clear arp-cache, on page 6

•local-proxy-arp, on page 7

•priority-timeout, on page 8

•proxy-arp, on page 9

•route distance, on page 10

•route metric, on page 11

•show arp, on page 11

•show arp traffic, on page 15

arp

To add a permanent entry in the Address Resolution Protocol (ARP) cache, use the arp command in XR

Config mode. To remove an entry from the ARP cache, enter the no form of this command.

arp [vrf vrf-name]ip-address hardware-address encapsulation-type [alias]

no arp [vrf vrf-name]ip-address hardware-address encapsulation-type [alias]

Syntax Description (Optional) Specifies VPN routing and forwarding (VRF) instance.vrf

ARP Commands

(Optional) VRF instance that identifies a VPN.vrf-name

IPv4 (network layer) address for which a permanent entry is added to the ARP cache.

Enter the IPv4 address in a four-part dotted-decimal format that corresponds to the local

data-link address (a 32-bit address).

ip-address

Hardware (data link layer) address that the IPv4 address is linked to. Enter the local

data-link address (a 48-bit address), such as 0800.0900.1834.

hardware-address

Encapsulation type. The encapsulation types are:

• arpa

• srp

• srpa

• srpb

For Ethernet interfaces, this is typically the arpa keyword.

encapsulation-type

(Optional) Causes the software to respond to ARP requests as if it were the owner of

both the specified IP address and hardware address, whether proxy ARP is enabled or

not.

alias

Command Default No entries are permanently installed in the ARP cache.

Command Modes XR Config mode

Command History ModificationRelease

This command was introduced.Release 6.0

Usage Guidelines The software uses ARP cache entries to translate 32-bit IP addresses into 48-bit hardware addresses.

Because most hosts support dynamic resolution, you generally need not specify static ARP cache entries.

Static entries are permanent entries that map a network layer address (IPv4 address) to a data-link layer address

(MAC address). If the alias keyword is specified when creating the entry, the interface to which the entry

is attached will act as if it is the owner of the specified addresses, that is, it will respond to ARP request packets

for this network layer address with the data link layer address in the entry.

The software does not respond to any ARP requests received for the specified IP address unless proxy ARP

is enabled on the interface on which the request is received. When proxy ARP is enabled, the software responds

to ARP requests with its own local interface hardware address.

To remove all nonstatic entries from the ARP cache, enter the clear arp-cache, on page 6 in XR EXEC mode.

Task ID OperationsTask

read,

write

cef

Examples The following is an example of a static ARP entry for a typical Ethernet host:

ARP Commands

arp

RP/0/RP0/CPU0:router# configure

RP/0/RP0/CPU0:router(config)# arp 192.168.7.19 0800.0900.1834 arpa

arp gratuitous ignore

To ignore receipt of gratuitous Address Resolution Protocol (ARP) packets, use the arp gratuitous ignore

command in interface configuration mode. To receipt gratuitous ARP packets, use the no form of this command.

arp gratuitous ignore

no arp gratuitous ignore

Syntax Description This command has no keywords or arguments.

Command Default Disabled

Command Modes Interface configuration

Command History ModificationRelease

This command was introduced.Release

6.0

Usage Guidelines No specific guidelines impact the use of this command.

Task ID OperationsTask

writecef

Examples This example shows how to configure arp gratuitous ignore command:

RP/0/# configure

RP/0/(config)# interface HundredGigE 0/1/0/0

RP/0/(config-if)# arp gratuitous ignore

arp learning

To enable the dynamic learning of ARP entries for a local subnet or all subnets, use the arp learning command.

To disable this command, use the no prefix or the disable option for this command.

arp learning local

ARP Commands

arp gratuitous ignore

no arp learning local

arp learning disable

no arp learning disable

Syntax Description Enables the dynamic learning of ARP entries for local subnets.

When arp learning local is configured on an interface or sub-interface, it learns only the ARP

entries from ARP packets on the same subnet.

local

Disables the dynamic learning of all ARP entries.disable

Command Default This command has no keywords or arguments.

Command Modes Sub-interface configuration mode

RP/0/RP0/CPU0:router(config)#interface GigabitEthernet 0/0/0/1

RP/0/RP0/CPU0:router(config-if)# ipv4 address 12.1.3.4 255.255.255.0

RP/0/RP0/CPU0:router(config-if)# arp learning local

RP/0/RP0/CPU0:router(config-if)# no shut

RP/0/RP0/CPU0:router(config-if)# commit

RP/0/RP0/CPU0:router(config)# interface GigabitEthernet 0/0/0/1

RP/0/RP0/CPU0:router(config-if)# ipv4 address 12.1.3.4 255.255.255.0

RP/0/RP0/CPU0:router(config-if)# arp learning disable

RP/0/RP0/CPU0:router(config-if)# commit

arp purge-delay

To delay purging Address Resolution Protocol (ARP) entries when an interface goes down, use the arp

purge-delay command in interface configuration mode. To turn off the purge delay feature, use the no form

of this command.

arp purge-delay value

no arp purge-delay value

Syntax Description Sets the purge delay time in seconds. Range is 1 to 65535.value

Command Default Default value is off.

Command Modes Interface configuration

Command History ModificationRelease

This command was introduced.Release 6.0

Usage Guidelines Use the arp purge-delay command to delay purging ARP entries when an interface goes down. If the interface

comes up within the delay time, then the ARP entries are restored to prevent packet loss with Equal Cost

Multipath (ECMP) configured.

ARP Commands

arp purge-delay

Task ID OperationsTask

read,

write

cef

Examples The following is an example of setting the purge delay to 50 seconds:

RP/0/# configure

RP/0/(config)# interface HundredGigE 0/0/0/0

RP/0/(config-if)# arp purge-delay 50

arp timeout

To specify the duration of dynamic entries learned on an interface remain in the Address Resolution Protocol

(ARP) cache, enter the arp timeout command in interface configuration mode. To remove the arp timeout

command from the configuration file and restore the system to its default condition with respect to this

command, enter the no form of this command.

arp timeout seconds

no arp timeout seconds

Syntax Description Indicates the time, in seconds, for which an entry remains in the ARP cache. Range is 30 to

4294967295.

seconds

Command Default Entries remain in the ARP cache for 14,400 seconds (4 hours).

Command Modes Interface configuration

Command History ModificationRelease

This command was supported.Release 6.0

Usage Guidelines This command is ignored when issued on interfaces that do not use ARP. Also, ARP entries that correspond

to the local interface or that are statically configured by the user never time out.

The arp timeout command applies only to the interface that is entered. When the timeout is changed for an

interface the change applies only to that interface.

The show interfaces command displays the ARP timeout value in hours:minutes:seconds, as follows:

ARP type: ARPA, ARP Timeout 04:00:00

ARP Commands

arp timeout

Task ID OperationsTask

read,

write

cef

Examples The following example shows how to set the ARP timeout to 3600 seconds to allow entries to time

out more quickly than the default:

RP/0/#configure

RP/0/(config)#interface HundredGigE 0/0/0/0

RP/0/(config-if)# arp timeout 3600

clear arp-cache

To delete all dynamic entries from the Address Resolution Protocol (ARP) cache, clear the fast-switching

cache, and clear the IP route cache, use the clear arp-cache command in .

clear arp-cache {traffic type interface-path-id|location node-id}

Syntax Description Deletes traffic statistics on the specified interface.traffic

Interface type. For more information, use the question mark (?) online help function.

t ype

Either a physical interface instance or a virtual interface instance as follows:

• Physical interface instance. Naming notation is rack/slot/module/port and a slash

between values is required as part of the notation.

•rack: Chassis number of the rack.

•slot: Physical slot number of the modular services card or line card.

•module: Module number. A physical layer interface module (PLIM) is always

•port: Physical port number of the interface.

• Virtual interface instance. Number range varies depending on interface type.

For more information about the syntax for the router, use the question mark (?) online

help function.

interface- path-id

Clears the ARP entries for a specified location. The node-id argument is entered in the

rack/slot/module notation.

location node-id

Command Default No default behavior or values

ARP Commands

clear arp-cache

Command Modes

Command History ModificationRelease

This command was introduced.Release

6.0

Usage Guidelines When issued without keywords or arguments, the clear arp-cache command clears all entries in the ARP

cache.

Task ID OperationsTask

executecef

Examples The following example shows how to remove traffic statistic entries from the ARP cache that match

the specified interface:

RP/0/# clear arp-cache traffic tengige 0/1/0/0 location 0/1/CPU0

The following example shows how to remove entries from the ARP cache that match the specified

location:

RP/0/# clear arp-cache location 0/1/CPU0

local-proxy-arp

To enable local proxy Address Resolution Protocol (ARP) on an interface, enter the local-proxy-arp command

in interface configuration mode. To disable local proxy ARP on the interface, enter the no form of this

command.

local-proxy-arp

no local-proxy-arp

Syntax Description This command has no keywords or arguments.

Command Default Local proxy ARP is disabled on all interfaces.

Command Modes Interface configuration

Command History ModificationRelease

This command was introduced.Release 6.0

ARP Commands

local-proxy-arp

Usage Guidelines When local proxy ARP is enabled, the networking device responds to ARP requests that meet all the following

conditions:

• The target IP address in the ARP request, the IP address of the ARP source, and the IP address of the

interface on which the ARP request is received are on the same Layer 3 network.

• The next hop for the target IP address is through the same interface as the request is received.

Typically, local proxy ARP is used to resolve MAC addresses to IP addresses in the same Layer 3 network

such as, private VLANs that are Layer 2-separated. Local proxy ARP supports all types of interfaces supported

by ARP and unnumbered interfaces.

Using the no form of the command removes the specified command from the configuration file and restores

the system to its default condition with respect to the command.

Task ID OperationsTask

read,

write

cef

priority-timeout

To configure the timer to time out a high-priority Direct Attached Gateway Redundancy (DAGR) route and

reverting to normal priority, use the priority-timeout command in DAGR peer interface configuration mode.

priority-timeout time

Syntax Description Time in seconds after which a high-priority route reverts to a normal priority route. The range of values

is 1 to 10000.

time

Command Default Default for time is 20 seconds.

Command Modes DAGR peer interface configuration

Command History ModificationRelease

This command was introduced.Release 6.0

Usage Guidelines To use this command, you must be in a user group associated with a task group that includes the proper task

IDs. If you suspect user group assignment is preventing you from using a command, contact your AAA

administrator for assistance.

When this function is applied, the DAGR group configuration is updated in the database.

The new timer values take effect the next time the timer is set. No immediate timer restarts are triggered on

the basis of this event.

ARP Commands

priority-timeout

Task ID OperationsTask

writecef

Examples The following example configures a priority timeout of 25 seconds:

RP/0/(config-if-dagr-peer)# priority-timeout 25

RP/0/(config-if-dagr-peer)#

proxy-arp

To enable proxy Address Resolution Protocol (ARP) on an interface, enter the proxy-arp command in interface

configuration mode. To disable proxy ARP on the interface, enter the no form of this command.

proxy-arp

no proxy-arp

Syntax Description This command has no keywords or arguments.

Command Default Proxy ARP is disabled on all interfaces.

Command Modes Interface configuration

Command History ModificationRelease

This command was introduced.Release 6.0

Usage Guidelines When proxy ARP is disabled, the networking device responds to ARP requests received on an interface only

if one of the following conditions is met:

• The target IP address in the ARP request is the same as the interface IP address on which the request is

received.

• The target IP address in the ARP request has a statically configured ARP alias.

When proxy ARP is enabled, the networking device also responds to ARP requests that meet all of the following

conditions:

• The target IP address is not on the same physical network (LAN) on which the request is received.

• The networking device has one or more routes to the target IP address.

• All of the routes to the target IP address go through interfaces other than the one on which the request

is received.

Using the no form of the command removes the specified command from the configuration file and restores

the system to its default condition with respect to the command.

ARP Commands

proxy-arp

Task ID OperationsTask

read,

write

cef

Examples The following example shows how to enable proxy ARP on HundredGigE interface 0/0/0/0:

RP/0/#(config)# interface HundredGigE 0/0/0/0

RP/0/#(config-if)# proxy-arp

route distance

To configure route distance for a given Direct Attached Gateway Redundancy (DAGR) group, use the route

distance command in DAGR peer interface configuration mode.

route distance normal normal-distance priority priority-distance

Syntax Description Sets normal route (administrative) distance. Range is 0 to 256.

normal normal-distance

Sets priority route (administrative) distance. Range is 0 to 256.

priority priority-distance

Command Default Default for normal-distance default is 150 and the default for priority-distance is 5.

Command Modes DAGR peer interface configuration

Command History ModificationRelease

This command was introduced.Release

6.0

Usage Guidelines The default setting for a priority distance takes precedence over that of a typical Internet Gateway Protocol

(IGP). The normal distance setting does not.

When this setting is applied, the DAGR group is updated in the database.

Task ID OperationsTask

writecef

Examples The following example configures a DAGR group peer with a normal route distance of 48 and priority

route distance of 5:

RP/0/(config-if-dagr-peer)# route distance normal 48 priority 5

RP/0/(config-if-dagr-peer)#

ARP Commands

route distance

Otros manuales para NCS 540 Series

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Enrutador de red de Cisco

Cisco

Cisco Catalyst 1900 Series Manual

Cisco

Cisco ASR 1000 Series Manual de usuario

Cisco

Cisco 1801 Manual de usuario

Cisco

Cisco RV260P Manual de usuario

Cisco

Cisco WS-C2960G-8TC-L Guía rápida

Cisco

Cisco NCS 5500 Series Manual de usuario

Cisco

Cisco 6500 - Catalyst Series 10 Gigabit EN Interface Module... Instrucciones de funcionamiento

Cisco

Cisco WIC-1ENET - 1700 Access Routers 1port10bt Enet Wan... Manual de usuario

Cisco

Cisco CSR 1000v Manual de programación

Cisco

Cisco XR 12000 Manual de servicio

Cisco

Cisco Linksys E-Series Guía de instalación

Cisco

Cisco 836 Manual

Cisco

Cisco SCE 1000 2xGBE Manual del operador

Cisco

Cisco ASR-920-10SZ-PD Manual de instrucciones

Cisco

Cisco RV042 - Small Business Dual WAN VPN Router Manual de usuario

Cisco

Cisco XR 12410 Manual de usuario

Cisco

Cisco Linksys RV0041 Instrucciones de uso

Cisco

Cisco 897VAW Manual de usuario

Cisco

Cisco 10000 Series Manual de usuario

Cisco

Cisco 1401 - 1401 Router - EN Guía de inicio rápido

Cisco

Cisco RV016 - Small Business - 10/100 VPN Router Manual de usuario

Cisco

Cisco WRT54G2 Linksys Manual de usuario

Cisco

Cisco 7603 - Modular Expansion Base Manual de usuario

Cisco

Cisco 1100 Series Manual de instrucciones

Manuales populares de Enrutador de red de otras marcas

Allnet

Allnet ALL0333AU Manual de usuario

HomeSeer

HomeSeer HT-SEL Manual de usuario

Sercomm

Sercomm Genesis OC3505D Manual de usuario

Billion

Billion BIPAC 5102 Series Manual de usuario

TP-Link

TP-Link TD-8817 Manual de usuario

Motorola

Motorola MR1900 Manual de usuario

Digi

Digi IX14 Manual de usuario

XAVi

XAVi X8821e Manual de usuario

BEC

BEC 6200WZL Manual de usuario

MikroTik

MikroTik hAP ac3 Series Manual de usuario

Korenix

Korenix JetNet 5428G Series Manual de usuario

NETGEAR

NETGEAR FS526T - Switch Manual de usuario

Korenix

Korenix JetNet 5710G Series Manual de usuario

Automated Logic

Automated Logic ZN551 Manual del propietario

EnGenius

EnGenius ESR-9710 Manual de usuario

LevelOne

LevelOne FBR-1416 Manual de usuario

Dynacord

Dynacord Promatrix 6000 Manual de usuario

Lorex

Lorex F5D8230-4 Manual de usuario