Cisco IAD1101 Manual de usuario
CHAPTER
2-1
Cisco IAD1101 Integrated Access Device Hardware Installation Guide
78-10836-01
2
Preparing for Installation
This chapter describes the tasks you must perform before you begin to install the Cisco IAD1101
integrated access device and includes the following sections:
•Safety
•Site Requirements
•Required Tools and Equipment
•Verifying Contents
Safety
Any device that uses electricity must be handled carefully; follow these guidelines to ensure general
safety:
•Keep the chassis area clear and dust-free during and after installation.
•Keep tools away from walk areas where you and others could fall over them.
•Do not wear loose clothing that could get caught in the chassis. Fasten your tie or scarf and roll up
your sleeves.
•Wear safety glasses if you are working under any conditions that might be hazardous to your eyes.
•Do not perform any action that creates a potential hazard to people or makes the equipment unsafe.
Warning
Ultimate disposal of this product should be handled according to all national laws and
regulations.
Maintaining Safety with Electricity
Warning
Before working on equipment that is connected to power lines, remove jewelry
(including rings, necklaces, and watches). Metal objects will heat up when connected
to power and ground and can cause serious burns or can weld the metal object to the
terminals.
2-2
Cisco IAD1101 Integrated Access Device Hardware Installation Guide 78-10836-01
Chapter 2 Preparing for Installation
Safety
Follow these guidelines when you work on equipment powered by electricity.
•Locate the emergency power-OFF switch for the room in which you are working. Then, if an
electrical accident occurs, you can act quickly to turn OFF the power.
•Before working on the system, unplug the power cord.
•Disconnect all power before doing the following:
–
Installing or removing a chassis
–
Working near power supplies
Warning
When installing the unit, the ground connection must always be made first and
disconnected last.
•Do not work alone if potentially hazardous conditions exist.
•Never assume that power is disconnected from a circuit. Always check.
Warning
Read the installation instructions before you connect the system to its power source.
•Look carefully for possible hazards in your work area, such as moist floors, ungrounded power
extension cables, frayed power cords, and missing safety grounds.
•If an electrical accident occurs, proceed as follows:
–
Use caution; do not become a victim yourself.
–
Turn OFF power to the system.
–
If possible, send another person to get medical aid. Otherwise, assess the condition of the
victim and then call for help.
–
Determine if the person needs rescue breathing or external cardiac compressions; then take
appropriate action.
Warning
This product relies on the building's installation for short-circuit (overcurrent)
protection. Ensure that a fuse or circuit breaker no larger than 120 VAC, 15A U.S. is used
on the phase conductors (all current-carrying conductors).
Preventing Electrostatic Discharge Damage
Electrostatic discharge (ESD) can damage equipment and impair electrical circuitry. ESD damage
occurs when electronic components are improperly handled and can result in complete or intermittent
failures.
Always follow ESD-prevention procedures when you remove and replace components. Ensure that the
chassis is electrically connected to earth ground. Wear an ESD-preventive wrist strap, ensuring that it
makes good skin contact. Connect the grounding clip to an unpainted surface of the chassis frame to
safely ground unwanted ESD voltages. To guard against ESD damage and shocks, the wrist strap and
cord must operate properly. If no wrist strap is available, ground yourself by touching the metal part of
the chassis.
2-3
Cisco IAD1101 Integrated Access Device Hardware Installation Guide
78-10836-01
Chapter 2 Preparing for Installation Site Requirements
Caution For safety, periodically check the resistance value of the antistatic strap, which should be
between 1 and 10 megohm (Mohm).
Site Requirements
This section describes the requirements your site must meet for safe installation and operation of your
system. Ensure that your site is properly prepared before beginning installation.
Environmental
The Cisco IAD1101 can be placed on a desktop or mounted in a rack or on a wall. The location of the
chassis and the layout of your equipment rack or wiring room are extremely important for proper system
operation. Placing equipment too close together, inadequate ventilation, and inaccessible panels can
make system maintenance difficult or cause system malfunctions and shutdowns.
The following precautions will help you plan an acceptable operating environment for your
Cisco IAD1101 and help you avoid environmentally-caused equipment failures:
•Ensure that the room in which you operate your system has adequate air circulation. Electrical
equipment generates heat. Ambient air temperature might not be able to cool equipment to
acceptable operating temperatures without adequate circulation.
•Always follow the ESD-prevention procedures described in the “Preventing Electrostatic Discharge
Damage” section to avoid damage to equipment. Damage from static discharge can cause
immediate or intermittent equipment failure.
•Ensure that the chassis cover is secure. The chassis is designed to allow cooling air to flow
effectively inside it. An open chassis allows air leaks, which might interrupt and redirect the flow
of cooling air from internal components. Do not operate the chassis without a the chassis cover
securely in place.
Power
Check the power at your site to ensure that you are receiving “clean” power (free of spikes and noise).
Install a power conditioner if necessary.
All units include a 6-foot (1.8-meter) electrical power cord. (A label near the power cord indicates the
correct voltage, frequency, current draw, and power dissipation for the unit.)
Warning
This product relies on the building's installation for short-circuit (overcurrent)
protection. Ensure that a fuse or circuit breaker no larger than 120 VAC, 15A U.S. is used
on the phase conductors (all current-carrying conductors).
2-4
Cisco IAD1101 Integrated Access Device Hardware Installation Guide 78-10836-01
Chapter 2 Preparing for Installation
Required Tools and Equipment
Rack-Mounting
The following information will help you plan an acceptable equipment rack configuration:
•Enclosed racks must have adequate ventilation. Ensure that the rack is not overly congested because
each unit generates heat. An enclosed rack should have louvered sides and a fan to provide cooling
air.
•When mounting a chassis in an open rack, ensure that the rack frame does not block the intake or
the exhaust ports. If the chassis is installed on slides, check the position of the chassis when it is
seated all the way into the rack.
•In an enclosed rack with a ventilation fan in the top, excessive heat generated by equipment near
the bottom of the rack can be drawn upward and into the intake ports of the equipment above it in
the rack. Ensure that you provide adequate ventilation for equipment at the bottom of the rack.
•Baffles can help to isolate exhaust air from intake air, which also helps to draw cooling air through
the chassis. The best placement of the baffles depends on the airflow patterns in the rack, which can
be found by experimenting with different arrangements.
Required Tools and Equipment
Installation might require some tools and equipment that are not provided as standard equipment with
the Cisco IAD1101. Following are the tools and parts required for a typical installation:
•Number 2 Phillips screwdriver.
•Flat-blade screwdrivers: small, 3/16-in. (0.476 cm) and medium, 1/4-in. (0.625 cm).
•Cables for connection to the Ethernet, V.35, and T1 ports (dependent on configuration).
•Ethernet 10BaseT hub or PC with a network interface card for connection to the Ethernet (LAN)
port(s).
Verifying Contents
The Cisco IAD1101 is shipped assembled in a cardboard box. Power cables, manuals, and other
additional items are packaged in a smaller accessory kit.
Remove the accessory kit from the box, open it and check the contents:
•Cisco IAD1101 Integrated Access Device Hardware Installation Guide (this document)
•Release Notes for Cisco 6700/IAD1100 Series
•Cisco documentation CD and warranty information
•Yellow straight-through Ethernet cable
•DB-9 serial adapter for Ethernet cable
•AC power cord
•Rack-mounting kits for 19 in. and 23 in. racks, including rack ears and screws
•Chassis grounding kit
•ESD wrist strap
Tabla de contenidos
Otros manuales de Hardware de red de Cisco
Cisco
Cisco Cisco 5400 ENCS Manual
Cisco
Cisco Catalyst 2960-XR Manual de usuario
Cisco
Cisco Nexus 3000 series Manual de usuario
Cisco
Cisco AIR-BR350-A-K9 - Aironet 350 Wireless Bridge Manual
Cisco
Cisco ISA500 Series Manual de instrucciones
Cisco
Cisco ASR 5000 Series Manual de usuario
Cisco
Cisco Aironet 1400 Series Manual de usuario
Cisco
Cisco SCE 1000 and Manual del operador
Cisco
Cisco N540X-6Z18G-SYS-A Manual de usuario
Cisco
Cisco CE-507 - Content Engine 507 Manual de usuario
Cisco
Cisco Cisco ASA Series Manual de usuario
Cisco
Cisco 15530-LCMB-0200 - ESCON Multiplexing Line Card... Manual
Cisco
Cisco ASR 5000 Manual de usuario
Cisco
Cisco MERAKI MR57 Manual de usuario
Cisco
Cisco Firepower 1010 Manual de usuario
Cisco
Cisco ASR 5500 Manual de instrucciones
Cisco
Cisco NCS 1001 Guía
Cisco
Cisco ASR 9000 Series Manual de usuario
Cisco
Cisco IAD2430 Series Manual
Cisco
Cisco CTM GateWay Guía de instalación
Manuales populares de Hardware de red de otras marcas
Matrix Switch Corporation
Matrix Switch Corporation MSC-HD161DEL Manual de usuario
B&B Electronics
B&B Electronics ZXT9-IO-222R2 Manual de usuario
Yudor
Yudor YDS-16 Manual de usuario
D-Link
D-Link ShareCenter DNS-320L Manual de usuario
Samsung
Samsung ES1642dc Instrucciones de uso
Honeywell Home
Honeywell Home LTEM-PV Instrucciones de montaje
