Cisco RSP7000 Manual de instrucciones

Doc. No.

Cisco Systems, Inc.

Installing the RSP7000 Upgrade Kit

in the Cisco 7000 Series Routers

78-2564-01

Product Number UPG-RSP7000=

This document contains instructions for installing the 7000 Series Route Switch Processor

(RSP7000) upgrade kit (UPG-RSP7000=) in the Cisco 7000 series routers: Cisco 7000 and Cisco

7010. This upgrade kit allows for 7500-series performance enhancements to the Cisco 7000 series

routers. The RSP7000 upgrade kit includes the following components:

•The 7000 Series Route Switch Processor (RSP7000) board, which installs only in the 7000 RSP

slot—slot 5 in the Cisco 7000, and slot 3 in the Cisco 7010

•The 7000 Series Chassis Interface (RSP7000CI) board, which installs only in the 7000 CI

slot—slot 6 in the Cisco 7000, and slot 4 in the Cisco 7010

The RSP7000 upgrade kit requires that your Cisco 7000 series router is running Cisco Internetwork

Operating System (Cisco IOS) Release 10.3(9), or later, Release 11.0(6), or later, or Release 11.1(1)

or later.

Caution Using the RSP7000 upgrade kit in your Cisco 7000 series router might require that some

currently installed interface processors be upgraded to speciﬁc, compatible hardware versions;

otherwise, error messages and erratic system behavior might result.You can use the show diag

command to see which interface processors in your system need this hardware upgrade. For a

complete list of the potentially affected interface processors, their required hardware versions, and

information on upgrading your affected interface processors, refer to the document Verifying

Interface Processor Compatibility with the Cisco 7500 Series Investment Protection Program (IPP),

Document Number 78-2077-xx, where xx refers to the latest version of this document.

The sections in this document include the following:

•Product Overview, page 2

•Installation Prerequisites, page 6

•Installing the RSP7000 Upgrade Kit, page 16

•Checking the Installation, page 21

•Customer Information Online, page 26

2Installing the RSP7000 Upgrade Kit in the Cisco 7000 Series Routers

Product Overview

Following are brief descriptions of the Cisco 7000 and Cisco 7010 routers, the RSP7000, and the

RSP7000CI.

What Is the Cisco 7000?

The Cisco 7000 is a seven-slot router chassis, which uses the new RSP7000. The Cisco 7000

provides up to ﬁve interface processor slots, and can accommodate the following CxBus-based

interface processors: Fast Ethernet, Ethernet, Token Ring, Fiber Distributed Data Interface (FDDI),

channel attachment, multichannel, serial, and so forth. The 7000 RSP and interface processors are

keyed with guides on the backplane to prevent them from being fully inserted in the wrong slot.

Figure 1 shows the rear of the Cisco 7000 router with the RSP7000 and RSP7000CI installed. In the

Cisco 7000 series, two slots are reserved for the 7000 Route Switch Processor (RSP7000), which

contains the system processor and performs packet switching functions, and the 7000 Chassis

Interface (RSP7000CI) board, which contains all of the environmental monitoring functions for the

Cisco 7000, when conﬁgured with the new 7000 RSP. The remaining slots (0 through 4) are for

interface processor.

Figure 1 Cisco 7000 with RSP7000 and RSP7000CI Installed

H5288

Interface processor slots 0 123 4 RSP

7000

slot 5

RSP

7000CI

slot 6

Upper 

power supply

Lower

power supply

DC FAIL

AC POWER

DC FAIL

AC POWER

Captive

installation screw

Captive

installation screw

EJECT

SLOT 0

SLOT 1

NORMAL

CPU HALT

RESET

AUX.

CONSOLE

ROUTE SWITCH PROCESSOR

ENABLE

Installing the RSP7000 Upgrade Kit in the Cisco 7000 Series Routers 3

Product Overview

What Is the Cisco 7010?

The Cisco 7010 is a ﬁve-slot chassis, which uses the new RSP7000 (and the RSP7000CI), and

provides up to three interface processor slots that can accommodate the following CxBus-based

interface processors: Fast Ethernet, Ethernet, Token Ring, Fiber Distributed Data Interface (FDDI),

channel attachment, multichannel, serial, and so forth. The processor and interface processors are

keyed with guides on the backplane to prevent them from being fully inserted in the wrong slot.

Figure 2 shows the rear of the Cisco 7010 router with the RSP7000 and RSP7000CI installed. In the

Cisco 7010, slots 3 and 4 are reserved for the RSP7000, which contains the system processor and

performs packet switching functions, and the RSP7000CI board, which contains all of the

environmental monitoring functions for the Cisco 7010. The remaining three slots (slots 0 through

2) are for interface processors.

Figure 2 Cisco 7010 with RSP7000 and RSP7000CI Installed

H5874

RSP7000CI slot 4

RSP7000 slot 3

Interface processor slot 1

DC OK LED

Power switch

Chassis ground

screw

Power receptacle

Interface processor slot 2

Interface processor slot 0

AC-input power supply

EJECT

SLOT 0

SLOT 1

NORMAL

CPU HALT

RESET

AUX.

CONSOLE

ROUTE SWITCH PROCESSOR

ENABLE

4Installing the RSP7000 Upgrade Kit in the Cisco 7000 Series Routers

Product Overview

What Is the RSP7000?

The RSP7000 is a new main system processor module for the Cisco 7000 series chassis. It combines

all of the switched routing and high-speed switching functions of the separate Route Processor (RP)

and Switch Processor (SP), which are used in the Cisco 7000 series routers, but with improved

performanceonasingleprocessormodule.TheRSP7000containsthecentralprocessingunit(CPU)

and most of the memory components for the Cisco 7000 series chassis.

Caution To prevent damage to the chassis slot and to the connector on the RSP7000, do not attempt

to install the RSP7000 in any other slot but the chassis’ 7000 RSP slot. Do not install the RSP7000

in the router’s Route Processor (RP) slot. You must install the RSP7000 in the appropriate chassis’

7000 RSP slot. (See Figure 1 on page 2, for the Cisco 7000, or Figure 2 on page 3 for the Cisco

7010.)

Note For the appropriate Cisco IOS version required for the RSP7000, refer to the section

“Software Prerequisites” on page 7.

Figure 3 RSP7000

Caution To prevent system problems, the RSP7000 must not be removed or installed with power

ON to the chassis. The RSP7000 does not support online insertion and removal (OIR).

H5364

CPU

Flash SIMM

holder Console port

Auxiliary port

NVRAM

Flash card

(PCMCIA) slot

DRAM

SIMMs

ROM monitor 

(boot ROM)

U12

U18

U25

U24

U17

Bus connector

Bank 0

Bank 1

Installing the RSP7000 Upgrade Kit in the Cisco 7000 Series Routers 5

Product Overview

What is the RSP7000CI?

The RSP7000CI, shown in Figure 4, consists of a printed circuit board attached to a metal carrier.

The RSP7000CI has no user-conﬁgurable jumpers or switches, and its faceplate contains no LEDs.

The RSP7000CI is distinguishable only by the label on its faceplate, which reads 7000 Series

Chassis Interface. (See Figure 4.) The RSP7000CI provides the environmental monitoring and

power supply monitoring functions for the Cisco 7000 series chassis. The RSP7000CI isolates the

CPU and system software from chassis-speciﬁc variations.

Caution Topreventsystemproblems,theRSP7000CImustnotberemovedor installed with power

ON to the chassis. The RSP7000CI does not support online insertion and removal (OIR). You must

installthe RSP7000CI in the appropriatechassis’ 7000 CI slot. (SeeFigure 1on page 2, for the Cisco

7000, or Figure 2 on page 3 for the Cisco 7010.)

Note For the appropriate Cisco IOS version required for the RSP7000CI, refer to the section

“Software Prerequisites” on page 7.

The functions of the RSP7000CI are as follows:

•Report backplane type

•Report arbiter type

•Monitor power supply status

•Monitor fan/blower status

•Monitor temperature sensors on the RSP7000

•Provide router power up/down control

•Provide power supply power-down control

Figure 4 RSP7000CI

H5300

6Installing the RSP7000 Upgrade Kit in the Cisco 7000 Series Routers

Installation Prerequisites

Before you begin this installation, review the safety guidelines in this section to avoid injuring

yourself or damaging the processor module.

Safety Guidelines

Following are safety guidelines that you should follow when working with any equipment that

connects to electrical power or telephone wiring.

Electrical Equipment Guidelines

Follow these basic guidelines when working with any electrical equipment:

•Before beginning any procedures requiring access to the chassis interior, locate the emergency

power-off switch for the room in which you are working.

•Disconnect all power and external cables before moving a chassis.

•Do not work alone when potentially hazardous conditions exist.

•Never assume that power has been disconnected from a circuit; always check.

•Do not perform any action that creates a potential hazard to people or makes the equipment

unsafe.

•Carefully examine your work area for possible hazards such as moist ﬂoors, ungrounded power

extension cables, and missing safety grounds; correct all hazardous conditions.

Telephone Wiring Guidelines

Use the following guidelines when working with any equipment that is connected to telephone

wiring or to other network cabling:

•Never install telephone wiring during a lightning storm.

•Never install telephone jacks in wet locations unless the jack is speciﬁcally designed for wet

locations, and use caution when installing or modifying telephone lines.

•Never touch uninsulated telephone wires or terminals unless the telephone line has been

disconnected at the network interface.

Preventing Electrostatic Discharge Damage

Electrostatic discharge (ESD) damage, which can occur when electronic cards or components are

improperly handled, results in complete or intermittent failures. Electromagnetic interference (EMI)

shielding and connectors are integral components of the carrier. Use a preventive antistatic strap

whenever handling a processor module.

Following are guidelines for preventing ESD damage:

•Always use an ESD wrist or ankle strap and ensure that it makes good skin contact.

•Connect the equipment end of the strap to a captive installation screw on an installed power

supply.

•Handle components by the edges only; avoid touching the board or connectors.

Installing the RSP7000 Upgrade Kit in the Cisco 7000 Series Routers 7

Installation Prerequisites

•Place a removed component on an antistatic surface or in a static shielding bag. If you plan to

return the component to the factory, immediately place it in a static shielding bag.

•Avoid contact between the component and clothing. The wrist strap only protects the board from

ESD voltages on the body; ESD voltages on clothing can still cause damage.

Caution For safety, periodically check the resistance value of the antistatic strap. The

measurement should be between 1 and 10 megohms.

Software Prerequisites

The RSP7000 upgrade kit requires that your Cisco 7000 series router is running Cisco Internetwork

Operating System (Cisco IOS) Release 10.3(9), or later, Release 11.0(6), or later, or Release 11.1(1)

or later.

The showversionand showhardwarecommands display the current hardware conﬁguration of the

router, including the system software version that is currently loaded and running. The

show microcodecommandlists the bundledmicrocode (targethardware) versionfor each processor

type. The show controller cbus command shows the microcode version you are running. (For

complete descriptions of show commands, refer to the Router Products Conﬁguration Guide and

Router Products Command Reference publications.)

You can determine the current version of software or microcode stored in ROM either by removing

the processor module and checking the ROM labels or by conﬁguring the system to boot the system

software or microcode from ROM, reloading the system, and using show commands to check the

version that is loaded and running. Refer to the appropriate software documentation for complete

conﬁguration instructions and examples.

If the displays indicate that the required system software and microcode is not available in your

system, contact a customer service representative for upgrade information. (Refer to the section

“Customer Information Online” at the end of this document.)

Hardware Prerequisites

You must install the RSP7000 in the appropriate chassis’ 7000 RSP slot. (See Figure 1, on page 2,

for the Cisco 7000, or Figure 2, on page 3, for the Cisco 7010.) For the RSP7000 to operate properly,

the Cisco 7000 and Cisco 7010 chassis must also be conﬁgured with the RSP7000CI.

List of Tools and Parts

Following are the tools and equipment that you will need to complete this replacement:

•ESD-prevention equipment (a disposable wrist strap is included with all spares and upgrade kits)

•Antistatic mat, foam pad, or bags for the removed RP and SP (or SSP) (Immediately place all

removed boards into antistatic bags if you plan to return them to the factory.)

•Number 2 Phillips or 3/16-inch ﬂat-blade screwdriver to loosen the processor module captive

installation screws, and replace the RP and SP (or SSP) with the RSP7000 and RSP7000CI

boards

•The RSP7000 upgrade kit, which includes the RSP7000 and the RSP7000CI

8Installing the RSP7000 Upgrade Kit in the Cisco 7000 Series Routers

Installation Prerequisites

Flash Memory Card Replacement and Formatting Prerequisites

If you have a Flash memory card installed in the PCMCIA slot of your RP, you must reformat it if

you want to use it with your new RSP7000. Using the RSP7000, you cannot read data on the RP’s

Flash memory card, nor can you use it as bootable media. You must reformat the RP’s Flash card

before you can use it with the RSP7000. Flash memory cards formatted on the RP-based systems

(7000 series routers) are formatted differently from Flash memory cards formatted on RSP-based

systems (7500 series routers).

Caution The formatting procedure erases all information on the Flash memory card. To prevent the

loss of important data that might be stored on a Flash memory card, proceed carefully. If you want

to save the data on a Flash memory card, copy the data to a server before you format the card.

Note Refer to the section “Uploading (Copying) the Conﬁguration File,” on page 12, and then the

section “Downloading (Retrieving) the Conﬁguration File,” on page 14.

Overview of Processor Module Replacement

When you remove or install a processor module, be sure to use the ejector levers, which help to

ensure that the processor module is fully inserted in the backplane or fully dislodged from it. Any

processor module that is only partially connected to the backplane can halt the system.

Figure 5 on page 9 shows a detail of the ejector lever mechanism in a vertical position that is

appropriate for the Cisco 7000. The processor module slots in the Cisco 7010 are oriented

horizontally. When you simultaneously push the ejector levers inward (toward the carrier handle),

the levers push the processor into the slot and ensure that the board connectors are fully seated in the

backplane.

In the Cisco 7000, the RSP7000 must be installed in the 7000 RSP slot (slot 5) and the RSP7000CI

must be installed in the 7000 CI slot (slot 6). In the Cisco 7010, the RSP7000 must be installed in

the 7000 RSP slot (slot 3) and the RSP7000CI must be installed in the 7000 CI slot (slot 4).

Installing the RSP7000 Upgrade Kit in the Cisco 7000 Series Routers 9

Installation Prerequisites

Note Figure 5 shows a typical processor module installation in a Cisco 7000, and is not intended

to indicate or recommend a particular slot location for the RSP7000 or the RSP7000CI. The

processor module slots in the Cisco 7010 are oriented horizontally (see Figure 7), but the function

of the captive installation screws and ejector levers is identical.

Figure 5 Ejector Levers and Captive Installation Screw

H1482a

Processor module

slot

STOP!

on contact

Bottom ejector lever

Captive

installation 

screw

Processor

module

carrier guide

10 Installing the RSP7000 Upgrade Kit in the Cisco 7000 Series Routers

Installation Prerequisites

Figure 6 shows how to orient a card for installation in the Cisco 7000. During installation, refer to

this illustration if you have a Cisco 7000.

Figure 6 Card-Installation Orientation in the Cisco 7000

Figure 7 shows how to orient a card for installation in the Cisco 7010. During installation, refer to

this illustration if you have a Cisco 7010.

Figure 7 Card-Installation Orientation in the Cisco 7010

H1355a

H1985

Captive installation 

screws

Otros manuales para RSP7000

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Hardware de red de Cisco

Cisco

Cisco NCS 1002 Actualización de firmware

Cisco

Cisco CVPN3002-K9 - Fast Ethernet VPN Gateway Manual de usuario

Cisco

Cisco NCS 1000 Manual de usuario

Cisco

Cisco IDS 4210 - Intrusion Detection Sys 4210... Manual de usuario

Cisco

Cisco AGS+ Manual de instrucciones

Cisco

Cisco GS7000 Instrucciones de funcionamiento

Cisco

Cisco Octal-Port DMT ATU-C Line Card Manual técnico

Cisco

Cisco GS7000 Instrucciones de funcionamiento

Cisco

Cisco WAE-674-K9 - Wide Area Application Engine... Manual

Cisco

Cisco MGX 8260 Guía de inicio rápido

Cisco

Cisco SCE 2000 4/8xFE Manual del operador

Cisco

Cisco SOURCEfire 3D500 Manual de usuario

Cisco

Cisco ONS 15454 Series Manual

Cisco

Cisco 1230AG - Aironet - Wireless Access Point Manual de usuario

Cisco

Cisco Aironet 340 Series Cómo utilizar

Cisco

Cisco Versatile Interface Processor (VIP6-80)... Manual del operador

Cisco

Cisco Firepower 1010 FPR1010-NGFW-K9 Manual

Cisco

Cisco Catalyst 8300 Series Manual

Cisco

Cisco Meraki Catalyst 9300/X/L-M Series Manual de usuario

Cisco

Cisco UCS 6248 UP Manual de usuario

Cisco

Cisco Edge 300 Series Guía de inicio rápido

Cisco

Cisco PIX Series Manual

Cisco

Cisco 15530-LCMB-0200 - ESCON Multiplexing Line Card... Manual

Cisco

Cisco Firepower 9300 Manual

Manuales populares de Hardware de red de otras marcas

Matrix Switch Corporation

Matrix Switch Corporation MSC-HD161DEL Manual de usuario

B&B Electronics

B&B Electronics ZXT9-IO-222R2 Manual de usuario

Yudor

Yudor YDS-16 Manual de usuario

D-Link

D-Link ShareCenter DNS-320L Manual de usuario

Samsung

Samsung ES1642dc Instrucciones de uso

Honeywell Home

Honeywell Home LTEM-PV Instrucciones de montaje

evertz

evertz 7700 Series Manual de usuario

D-Link

D-Link ShareCenter DNS-343 Manual de usuario

Asante

Asante AsanteBridge 1012 Manual de usuario

FireBrick

FireBrick FB2700 Manual de usuario

Audiovox Electronics

Audiovox Electronics ARWH2T Manual de usuario

ADC

ADC DSX-1 Manual

NetComm

NetComm NF2 Manual de usuario

Alcatel-Lucent

Alcatel-Lucent 5620 Manual de usuario

Dell EMC

Dell EMC XC6420 Series Manual de usuario

Lanner

Lanner NCA-1020A Manual de usuario

Allied Telesis

Allied Telesis AT-TN121-A Manual de usuario

Arista

Arista CCA-ETM-Q12 Manual de usuario