Cisco ONS 15310-MA SDH Manual
CHAPTER
1-1
Cisco ONS 15310-MA SDH Procedure Guide, R9.0
78-18668-01
1
Install the Cisco ONS 15310-MA SDH
This chapter provides procedures for installing the Cisco ONS 15310-MA SDH shelf, cards, and
fiber-optic cable. To view a summary of the tools and equipment required for installation, see the
“Required Tools and Equipment” section on page 1-3.
Before You Begin
This section lists the chapter procedures (NTPs). Turn to a procedure for applicable tasks (DLPs).
1. NTP-H149 Unpack and Inspect the ONS 15310-MA SDH Shelf Assembly, page 1-5—Complete
this procedure before continuing with the “NTP-H150 Install the Shelf Assembly” procedure on
page 1-5.
2. NTP-H150 Install the Shelf Assembly, page 1-5—Complete this procedure to install the shelf
assembly in a rack before continuing with the “NTP-H151 Install the Power and Ground” procedure
on page 1-12 or before completing one of the following optional procedures.
3. NTP-H169 Install the Cable Management Bracket, page 1-6—As needed, complete this procedure
to install the cable management bracket.
4. NTP-H166 Remove the Blank Sheet Metal Covers, page 1-9—As needed, complete this procedure
to access the backplane.
5. NTP-H167 Install the EIAs, page 1-10—As needed, complete this procedure to install the electrical
interface assemblies (EIAs) before continuing with the “NTP-H151 Install the Power and Ground”
procedure on page 1-12.
6. NTP-H151 Install the Power and Ground, page 1-12—Complete this procedure before continuing
with the “NTP-H152 Install the Fan-Tray Assembly” procedure on page 1-14.
7. NTP-H152 Install the Fan-Tray Assembly, page 1-14—Complete this procedure before continuing
with the “NTP-H153 Install the 15310E-CTX-K9 Cards” procedure on page 1-16.
8. NTP-H153 Install the 15310E-CTX-K9 Cards, page 1-16—Complete this procedure to install the
common- control/cross-connect cards.
9. NTP-H154 Install the Ethernet Cards, page 1-19—As needed, complete this procedure to install an
Ethernet card.
10. NTP-H187 Install STM-N Cards and Connectors, page 1-20—As needed, complete this procedure
to install STM-N cards and connectors.
11. NTP-H155 Install the Electrical Cards, page 1-23—As needed, complete this procedure to install an
electrical card.
1-2
Cisco ONS 15310-MA SDH Procedure Guide, R9.0
78-18668-01
Chapter 1 Install the Cisco ONS 15310-MA SDH
Before You Begin
12. NTP-H156 Install the Filler Cards, page 1-24—As needed, complete this procedure to install a filler
card (blank faceplate) in the expansion slot. If no Ethernet or electrical card is installed in the
expansion slot, you must install a filler card.
13. NTP-H157 Install Wires to Alarm, Timing, Craft, LAN, and UDC Pin Connections,
page 1-25—Complete this procedure to install cables for alarms, timing, LAN, craft, and user data
channel (UDC) connections.
14. NTP-H158 Install the Electrical Cables, page 1-26—Complete this procedure to connect and route
cables that will carry electrical traffic.
15. NTP-H159 Install and Remove SFPs, page 1-27—As needed, complete this procedure to install
Small Form-factor Pluggables (SFPs) that provide a fiber-optic interface to the 15310E-CTX-K9
card.
16. NTP-H160 Install Optical Cables, page 1-28—Complete this procedure to connect and route cables
that will carry optical traffic.
17. NTP-H164 Perform the Shelf Installation Acceptance Test, page 1-30—Complete this procedure to
determine if you have correctly completed all other procedures in the chapter.
18. NTP-H161 Preprovision an SFP Slot, page 1-31—As needed, complete this procedure to
preprovision SFPs, which provide a fiber-optic interface to the ONS 15310-MA SDH and can be
provisioned for various line rates.
19. NTP-H162 Preprovision a Card Slot, page 1-32—As needed, complete this procedure to
preprovision an empty card slot with a card that will be installed later.
20. NTP-H163 Remove and Replace a Card, page 1-32—As needed, complete this procedure to remove
and replace an ONS 15310-MA SDH card.
21. NTP-H168 Install the Front Door, page 1-34—As needed, complete this procedure to install the
front door.
22. NTP-H191 Install the Rear Cover, page 1-36—As needed, complete this procedure to install the rear
cover.
Warning
Only trained and qualified personnel should be allowed to install, replace, or service this equipment.
Statement 1030
Warning
This unit is intended for installation in restricted access areas. A restricted access area can be
accessed only through the use of a special tool, lock and key, or other means of security.
Statement 1017
Warning
Installation of the equipment must comply with local and national electrical codes.
Statement 1074
Warning
Ultimate disposal of this product should be handled according to all national laws and regulations.
Statement 1040
Note The ONS 15310-MA SDH is designed to comply with Telcordia GR-1089-CORE Type 2 and Type 4.
Acceptable applications include Central Office Environments (COEs), Electronic Equipment Enclosures
(EEEs), Controlled Environment Vaults (CEVs), huts, and Customer Premise Environments (CPEs).
1-3
Cisco ONS 15310-MA SDH Procedure Guide, R9.0
78-18668-01
Chapter 1 Install the Cisco ONS 15310-MA SDH
Required Tools and Equipment
Note The Cisco ONS 15310-MA SDH is intended for use with telecommunications equipment only.
Warning
The intra-building ports of the ONS15310-MA SDH are suitable only for connecting to intrabuilding or
unexposed wiring or cabling. The intra-building ports of ONS15310-MA SDH MUST NOT be
metallically connected to interfaces that connect to the OSP or its wiring. These interfaces are
designed for use as intra-building interfaces only (Type 2 or Type 4 ports as described in
GR-1089-CORE, Issue 4) and require isolation from the exposed OSP cabling. The addition of Primary
Protectors is not sufficient protection in order to connect these interfaces metallically to OSP wiring.
Required Tools and Equipment
You will need the following tools and equipment to install and test the ONS 15310-MA SDH.
lncluded Materials
These materials are shipped with the ONS 15310-MA SDH. The number in parentheses provides the
quantity of the item included in the package.
•Ground lug (1)
•Screws: panhead, 10-32 x 0.375 (10)
•Screws: panhead, 10-32 x 0.37, green zinc (2)
•Screws: panhead, 12-24 x 0.75 (8)
•Screws: panhead, 10-32 x 0.31 (2)
•Screws: panhead, 8-32 x 0.31 (3)
•Kep nut: 10-32 x 0.170
•Rack mount bracket
•Interconnect plate
•Rack mount bracket for 19-inch rack
•Cable routing bracket
User-Supplied Materials
These materials and tools are required but are not supplied with the ONS 15310-MA SDH.
•Equipment rack (26 inches total width for a 19-inch rack)
•Fuse and alarm panel
•Copper power cable (from fuse and alarm panel to assembly), #12 AWG
•Ground cable, #6 AWG stranded (minimum)
•Alarm In cable, unshielded cable terminated with a DB-37 connector
•Alarm Out cable, shielded cable terminated with a DB-25 connector
1-4
Cisco ONS 15310-MA SDH Procedure Guide, R9.0
78-18668-01
Chapter 1 Install the Cisco ONS 15310-MA SDH
Required Tools and Equipment
•Craft port serial cable, CAT-5 terminated with RJ-45
•BITS timing port cable, CAT-3/CAT-5 terminated with DB-9 connector
•User data channel (UDC) cable: EIA/TIA-232 port cable, CAT-5 terminated with RJ-45
•Management LAN cable, CAT-5 terminated with RJ-45
•Single-mode LC fiber jumpers with UPC polish (55 dB or better) for optical interfaces
•E1 cabling, shielded, terminated to a 21-pair #26AWG cable, with dual 64-pin CHAMP connectors
at far end with separate transmit and receive, straight termination (optional)
•Shielded coaxial cable terminated with BNC connectors for DS-3/E3 ports
•Tie wraps and/or lacing cord
•Labels
Tools Needed
The following tools are needed to complete the procedures in this chapter:
•#2 Phillips screw driver
•Medium slot head screw driver
•Small slot head screw driver
•Wire cutters
•Wire strippers
Test Equipment
The following test equipment is needed to complete the procedures in this chapter:
•Volt meter
•Power meter (for use with fiber optics only)
•Bit error rate (BER) tester, E1 and DS-3/E3
Note In this chapter, the terms “ONS 15310-MA SDH” and “shelf assembly” are used interchangeably. In the
installation context, these terms have the same meaning. Otherwise, shelf assembly refers to the physical
steel enclosure that holds cards and connects power, and ONS 15310-MA SDH refers to the entire
system, both hardware and software.
1-5
Cisco ONS 15310-MA SDH Procedure Guide, R9.0
78-18668-01
Chapter 1 Install the Cisco ONS 15310-MA SDH
Required Tools and Equipment
NTP-H149 Unpack and Inspect the ONS 15310-MA SDH Shelf
Assembly
Step 1 Complete the “DLP-H1 Unpack and Verify the Shelf Assembly” task on page 16-1.
Step 2 Complete the “DLP-H2 Inspect the Shelf Assembly” task on page 16-1.
Step 3 Continue with the “NTP-H150 Install the Shelf Assembly” procedure on page 1-5.
Stop. You have completed this procedure.
NTP-H150 Install the Shelf Assembly
Note The ONS 15310-MA SDH installations are suitable for Network Telecommunication facilities and
locations where NEC are applicable.
Purpose This procedure describes how to unpack the ONS 15310-MA SDH and
verify the contents.
Tools/Equipment None
Prerequisite Procedures None
Required/As Needed Required
Onsite/Remote Onsite
Security Level None
Purpose This procedure describes how to mount ONS 15310-MA SDH shelf
assemblies in a rack.
Tools/Equipment #2 Phillips screwdriver
#12-24 mounting screws (4)
#10-32 ear mounting screws (8)
Universal mounting ears (2)
Dual-assembly plate
19-inch-rack mounting ear
Fuse and alarm panel, if not installed
Prerequisite Procedures NTP-H149 Unpack and Inspect the ONS 15310-MA SDH Shelf Assembly,
page 1-5
Required/As Needed Required
Onsite/Remote Onsite
Security Level None
1-6
Cisco ONS 15310-MA SDH Procedure Guide, R9.0
78-18668-01
Chapter 1 Install the Cisco ONS 15310-MA SDH
Required Tools and Equipment
Warning
To prevent the system from overheating, do not operate it in an area that exceeds the maximum
recommended ambient temperature of 149°F (65°C).
Statement 1047
Warning
To prevent bodily injury when mounting or servicing this unit in a rack, you must take special
precautions to ensure that the system remains stable. The following guidelines are provided to ensure
your safety:
• This unit should be mounted at the bottom of the rack if it is the only unit in the rack.
• When mounting this unit in a partially filled rack, load the rack from the bottom to the top with the
heaviest component at the bottom of the rack.
• If the rack is provided with stabilizing devices, install the stabilizers before mounting or servicing
the unit in the rack.
Statement 1006
Step 1 Complete the necessary rack mount task DLP-H248 Mount a Single ONS 15310-MA SDH in a Rack,
page 18-49.
Step 2 Continue with the “NTP-H169 Install the Cable Management Bracket” procedure on page 1-6.
Stop. You have completed this procedure.
NTP-H169 Install the Cable Management Bracket
Warning
The covers are an integral part of the safety design of the product. Do not operate the unit without the
covers installed.
Statement 1077
Step 1 Line up the three screw holes on the rear of the bracket with the screw holes at the bottom of the
ONS 15310-MA SDH shelf assembly (Figure 1-1).
Purpose This procedure describes how to install the cable management bracket,
which is used for routing optical and Ethernet cables.
Tools/Equipment #2 Phillips screwdriver
Standard cable management bracket and
three #8-32 x 0.31 inch (0.79 cm) screws (included with the ship kit)
or
Extended cable management bracket (15310-CBLMGT) and
five 8-32 x 0.31 inch (0.79 cm) screws
Prerequisite Procedures NTP-H150 Install the Shelf Assembly, page 1-5
Required/As Needed Required
Onsite/Remote Onsite
Security Level None
1-7
Cisco ONS 15310-MA SDH Procedure Guide, R9.0
78-18668-01
Chapter 1 Install the Cisco ONS 15310-MA SDH
Required Tools and Equipment
Figure 1-1 Installing the Standard Cable Management Bracket
Step 2 To secure the bracket to the shelf, use the screwdriver to install three 8-32 x 0.31 inch (0.79 cm) screws,
torqued to 15 to 18 inch-lbs.
Step 3 If you are installing the extended bracket, install two 8-32 x 0.31 inch (0.79 cm) screws, torqued to 15
to 18 inch-lbs, through the top of the bracket directly into the ESD faceplates adjacent to Slots 1 and 6
on either side of shelf (Figure 1-2).
151577
1-8
Cisco ONS 15310-MA SDH Procedure Guide, R9.0
78-18668-01
Chapter 1 Install the Cisco ONS 15310-MA SDH
Required Tools and Equipment
Figure 1-2 Installing the Extended Cable Management Bracket
Step 4 If you plan to install electrical interface assemblies (EIAs), continue with the “NTP-H166 Remove the
Blank Sheet Metal Covers” procedure on page 1-9 to access the backplane. If not, continue with the
“NTP-H151 Install the Power and Ground” procedure on page 1-12.
Stop. You have completed this procedure.
151578
1-9
Cisco ONS 15310-MA SDH Procedure Guide, R9.0
78-18668-01
Chapter 1 Install the Cisco ONS 15310-MA SDH
Required Tools and Equipment
NTP-H166 Remove the Blank Sheet Metal Covers
Warning
The covers are an integral part of the safety design of the product. Do not operate the unit without the
covers installed.
Statement 1077
Step 1 Use a Phillips screwdriver to remove the five screws holding each sheet metal cover in place.
Figure 1-3 shows the screw locations of the sheet metal covers installed on the A-side and B-side of the
ONS 15310-MA SDH.
Figure 1-3 Blank Sheet Metal Covers
Step 2 Store the panels for later use. Attach the backplane cover(s) whenever EIA(s) are not installed.
Purpose This procedure describes how to access the backplane by removing the
blank sheet metal covers. The backplane has two sheet metal covers (one
on either side).
Tools/Equipment #2 Phillips screwdriver
Prerequisite Procedures NTP-H150 Install the Shelf Assembly, page 1-5
Required/As Needed Required
Onsite/Remote Onsite
Security Level None
151576
Blank sheet metal cover
installed on the B Side
Blank sheet metal cover
installed on the A Side
1-10
Cisco ONS 15310-MA SDH Procedure Guide, R9.0
78-18668-01
Chapter 1 Install the Cisco ONS 15310-MA SDH
Required Tools and Equipment
Step 3 If you plan to install electrical interface assemblies (EIAs), continue with the “NTP-H167 Install the
EIAs” procedure on page 1-10. If not, continue with the “NTP-H151 Install the Power and Ground”
procedure on page 1-12.
Stop. You have completed this procedure.
NTP-H167 Install the EIAs
Caution Connect only SELV services to the high-density EIAs on the ONS 15310-MA SDH.
Step 1 Determine which high-density EIA is designed for installation on the B Side and which is designed for
installation on the A Side (Figure 1-4).
Purpose This procedure describes how to install electrical interface assemblies
(EIAs). Refer to the Cisco ONS 15310-MA SDH Reference Manual for
descriptions of the EIAs.
Tools/Equipment #2 Phillips screwdriver
High-density EIA(s)
6-32 x 5/16-inch pan head screws (3, included with EIA)
Prerequisite Procedures NTP-H169 Install the Cable Management Bracket, page 1-6
Required/As Needed As needed
Onsite/Remote Onsite
Security Level None
Otros manuales para ONS 15310-MA SDH
1
Tabla de contenidos
Otros manuales de Hardware de red de Cisco
Cisco
Cisco ONS 15600 Manual de usuario
Cisco
Cisco IAD2430 Series Guía de instalación
Cisco
Cisco SCE8000 GBE Manual de usuario
Cisco
Cisco Firepower 1100 Series Manual
Cisco
Cisco Firepower 1010 Manual de usuario
Cisco
Cisco Aironet 340 Series Manual de usuario
Cisco
Cisco Nexus 3000 series Manual de usuario
Cisco
Cisco MA-UMNT-MR-A3 Manual de usuario
Cisco
Cisco Aironet 340 Series Manual de usuario
Cisco
Cisco Engine 611 Manual de usuario
Cisco
Cisco Firepower 9300 Manual
Cisco
Cisco ONS 15454 Hoja de instrucciones
Cisco
Cisco CSS11501 - 100Mbps Ethernet Load Balancing... Manual de usuario
Cisco
Cisco DS-X9530-SF1-K9 - Supervisor-1 Module - Control... Manual de usuario
Cisco
Cisco ASA 5506-X Manual
Cisco
Cisco CTM GateWay Guía de instalación
Cisco
Cisco 5400 Manual de usuario
Cisco
Cisco 3660 Series Manual de usuario
Cisco
Cisco Firepower 4100 Series Manual de usuario
Cisco
Cisco 5500 Series Manual de usuario
Manuales populares de Hardware de red de otras marcas
Matrix Switch Corporation
Matrix Switch Corporation MSC-HD161DEL Manual de usuario
B&B Electronics
B&B Electronics ZXT9-IO-222R2 Manual de usuario
Yudor
Yudor YDS-16 Manual de usuario
D-Link
D-Link ShareCenter DNS-320L Manual de usuario
Samsung
Samsung ES1642dc Instrucciones de uso
Honeywell Home
Honeywell Home LTEM-PV Instrucciones de montaje
