Cisco 8011-2X2XP4L Manual

Hardware Installation Guide for Cisco 8011-2X2XP4L PLE Service

Endpoint Router

First Published: 2023-12-08

Americas Headquarters

Cisco Systems, Inc.

170 West Tasman Drive

San Jose, CA 95134-1706

USA

http://www.cisco.com

Tel: 408 526-4000

800 553-NETS (6387)

Fax: 408 527-0883

THE SPECIFICATIONS AND INFORMATION REGARDING THE PRODUCTS IN THIS MANUAL ARE SUBJECT TO CHANGE WITHOUT NOTICE. ALL STATEMENTS,

INFORMATION, AND RECOMMENDATIONS IN THIS MANUAL ARE BELIEVED TO BE ACCURATE BUT ARE PRESENTED WITHOUT WARRANTY OF ANY KIND,

EXPRESS OR IMPLIED. USERS MUST TAKE FULL RESPONSIBILITY FOR THEIR APPLICATION OF ANY PRODUCTS.

THE SOFTWARE LICENSE AND LIMITED WARRANTY FOR THE ACCOMPANYING PRODUCT ARE SET FORTH IN THE INFORMATION PACKET THAT SHIPPED WITH

THE PRODUCT AND ARE INCORPORATED HEREIN BY THIS REFERENCE. IF YOU ARE UNABLE TO LOCATE THE SOFTWARE LICENSE OR LIMITED WARRANTY,

CONTACT YOUR CISCO REPRESENTATIVE FOR A COPY.

The Cisco implementation of TCP header compression is an adaptation of a program developed by the University of California, Berkeley (UCB) as part of UCB's public domain version of

NOTWITHSTANDING ANY OTHER WARRANTY HEREIN, ALL DOCUMENT FILES AND SOFTWARE OF THESE SUPPLIERS ARE PROVIDED “AS IS" WITH ALL FAULTS.

CISCO AND THE ABOVE-NAMED SUPPLIERS DISCLAIM ALL WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING, WITHOUT LIMITATION, THOSE OF

MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT OR ARISING FROM A COURSE OF DEALING, USAGE, OR TRADE PRACTICE.

IN NO EVENT SHALL CISCO OR ITS SUPPLIERS BE LIABLE FOR ANY INDIRECT, SPECIAL, CONSEQUENTIAL, OR INCIDENTAL DAMAGES, INCLUDING, WITHOUT

LIMITATION, LOST PROFITS OR LOSS OR DAMAGE TO DATA ARISING OUT OF THE USE OR INABILITY TO USE THIS MANUAL, EVEN IF CISCO OR ITS SUPPLIERS

HAVE BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.

Any Internet Protocol (IP) addresses and phone numbers used in this document are not intended to be actual addresses and phone numbers. Any examples, command display output, network

topology diagrams, and other figures included in the document are shown for illustrative purposes only. Any use of actual IP addresses or phone numbers in illustrative content is unintentional

and coincidental.

All printed copies and duplicate soft copies of this document are considered uncontrolled. See the current online version for the latest version.

Cisco has more than 200 offices worldwide. Addresses and phone numbers are listed on the Cisco website at www.cisco.com/go/offices.

Cisco and the Cisco logo are trademarks or registered trademarks of Cisco and/or its affiliates in the U.S. and other countries. To view a list of Cisco trademarks, go to this URL:

https://www.cisco.com/c/en/us/about/legal/trademarks.html. Third-party trademarks mentioned are the property of their respective owners. The use of the word partner does not imply a

partnership relationship between Cisco and any other company. (1721R)

CONTENTS

Safety Warnings 1

CHAPTER 1

Standard Warning Statements 1

Safety Guidelines for Personal Safety and Equipment Protection 3

Safety Precautions for Module Installation and Removal 3

Safety with Electricity 4

Cautions and Regulatory Compliance Statements for NEBS 7

Power Supply Considerations 7

Power Connection Guidelines 7

Guidelines for DC-Powered Systems 8

Guidelines for AC-Powered Systems 8

Prevent Power Loss 8

Preventing ESD Damage 9

Cisco 8011-2X2XP4L PLE Service Endpoint Router Overview 11

CHAPTER 2

Temperature and Physical Specification 12

Cisco 8011-2X2XP4L PLE Service Endpoint Router Features 12

Network Interfaces 12

Interface Naming 13

USB Console 13

Online Insertion and Removal 13

Supported Transceiver Modules 14

Prepare for Installation 15

CHAPTER 3

General Precautions 15

Site Planning Checklist 16

Environmental Requirements 16

Hardware Installation Guide for Cisco 8011-2X2XP4L PLE Service Endpoint Router

iii

Airflow Guidelines 16

Site Power Guidelines 18

Electrical Circuit Requirements 19

Site Cabling Guidelines 19

Asynchronous Terminal Connections 19

Interference Considerations 19

Electromagnetic Interference 20

Radio Frequency Interference 20

Lightning and AC Power Fault Interference 20

Tools and Equipment 20

Prepare Your Location 21

Prepare Yourself 21

Prepare Rack for Router Installation 22

Cabinet Selection Guidelines 22

Unpack the Cisco 8011 Router 23

Install the Device 27

CHAPTER 4

Rack Mounting the Router 27

Rack Mounting Brackets 30

Mounting the Router on the Rack 31

Wall Mount 36

Ground the Device 38

Install the AC Power Cables 40

Install the DC Power Cables 41

Port Connection Guidelines 43

Connect to the Console Port 43

Connect to the Management Ethernet Port 44

Install and Remove Transceiver Module 45

Safety Precautions for Module Installation and Removal 45

Install and Remove SFP Modules 46

Bale Clasp SFP or SFP+ Module 47

Install a Bale Clasp SFP or SFP+ Module 48

Remove a Bale Clasp SFP or SFP+ Module 49

Connect Interface Ports 51

Hardware Installation Guide for Cisco 8011-2X2XP4L PLE Service Endpoint Router

Contents

Connect a Fiber-Optic Port to the Network 51

Disconnect Optical Ports from the Network 51

Maintain Transceivers and Optical Cables 51

Configure the Device 53

CHAPTER 5

Create the Initial Router Configuration 53

Verify Device Installation 54

Replace Power Supply 57

CHAPTER 6

Remove the DC Power Supply Module 58

Install the DC Power Supply Module 58

Remove the AC Power Supply Module 59

Install the AC Power Supply Module 60

Appendix 61

CHAPTER 7

LEDs 61

Router LEDs 61

Fan Assembly LEDs 63

Power Status LEDs 63

Combination of LEDs 63

SFP and SFP+ Port LEDs 64

Management Port LEDs 64

System Specifications 64

RJ45 Connectors 65

Transceiver and Cable Specifications 66

Console Port Pinouts 66

USB Port Console Pinouts 66

USB Port Memory Pinouts 67

Management Ethernet Port Pinouts 67

Hardware Installation Guide for Cisco 8011-2X2XP4L PLE Service Endpoint Router

Contents

Hardware Installation Guide for Cisco 8011-2X2XP4L PLE Service Endpoint Router

Contents

CHAPTER 1

Safety Warnings

This handout lists the safety warnings necessary for handling this chassis. Before you install or service the

chassis, review these safety warnings to avoid injuring yourself or damaging the equipment.

For a complete list of translated safety warnings, see the Regulatory Compliance and Safety Information —

Cisco 8000 Series Routers.

The safety warnings are grouped under the following sections:

•Standard Warning Statements, on page 1

•Safety Guidelines for Personal Safety and Equipment Protection, on page 3

•Safety Precautions for Module Installation and Removal, on page 3

•Safety with Electricity, on page 4

•Cautions and Regulatory Compliance Statements for NEBS, on page 7

•Power Supply Considerations, on page 7

•Preventing ESD Damage, on page 9

Standard Warning Statements

Statement 407—Japanese Safety Instruction

You are strongly advised to read the safety instruction before using the product.

https://www.cisco.com/web/JP/techdoc/pldoc/pldoc.html

When installing the product, use the provided or designated connection cables/power cables/AC adapters.

Note

Statement 1003—DC Power Disconnection

To reduce risk of electric shock or personal injury, disconnect DC power before removing or replacing

components or performing upgrades.

Warning

Hardware Installation Guide for Cisco 8011-2X2XP4L PLE Service Endpoint Router

Statement 1006—Chassis Warning for Rack-Mounting and Servicing

To prevent bodily injury when mounting or servicing this unit in a rack, you must take special precautions to

ensure that the system remains stable. The following guidelines are provided to ensure your safety:

• This unit should be mounted at the bottom of the rack if it is the only unit in the rack.

• When mounting this unit in a partially filled rack, load the rack from the bottom to the top with the

heaviest component at the bottom of the rack.

• If the rack is provided with stabilizing devices, install the stabilizers before mounting or servicing the

unit in the rack.

Warning

Statement 1022—Disconnect Device

To reduce the risk of electric shock and fire, a readily accessible disconnect device must be incorporated in

the fixed wiring.

Warning

Statement 1024—Ground Conductor

This equipment must be grounded. To reduce the risk of electric shock, never defeat the ground conductor or

operate the equipment in the absence of a suitably installed ground conductor. Contact the appropriate electrical

inspection authority or an electrician if you are uncertain that suitable grounding is available.

Warning

Statement 294—Class A Warning for Korea

This is a Class A device and is registered for electromagnetic compatibility (EMC) requirements for industrial

use. The seller or buyer should be aware of this. If this type was sold or purchased by mistake, it should be

replaced with a residential-use type.

Warning

Statement 1049—Rack Installation

To reduce the risk of bodily injury, mount the chassis on a rack that is permanently affixed to the building.

Warning

Statement 9001—Product Disposal

Ultimate disposal of this product should be handled according to all national laws and regulations.

Warning

Hardware Installation Guide for Cisco 8011-2X2XP4L PLE Service Endpoint Router

Safety Warnings

Standard Warning Statements

Statement 1017—Restricted Area

This unit is intended for installation in restricted access areas. Only skilled, instructed, or qualified personnel

can access a restricted access area.

Warning

Statement 1071—Warning Definition

IMPORTANT SAFETY INSTRUCTIONS

Before you work on any equipment, be aware of the hazards involved with electrical circuitry and be familiar

with standard practices for preventing accidents. Read the installation instructions before using, installing, or

connecting the system to the power source. Use the statement number at the beginning of each warning

statement to locate its translation in the translated safety warnings for this device.

SAVE THESE INSTRUCTIONS

Warning

Safety Guidelines for Personal Safety and Equipment Protection

The following guidelines ensure your safety and protect the equipment. This list does not include all the

potentially hazardous situations. Therefore, you must be alert.

• Before moving the system, always disconnect all power cords and interface cables.

• Never assume that power is disconnected from a circuit; always check.

• Before and after installation, keep the chassis area clean and dust free.

• Keep tools and assembly components away from walk areas where you or others can trip over them.

• Do not work alone if potentially hazardous conditions exist.

• Do not perform any action that creates a potential hazard to people or makes the equipment unsafe.

• Do not wear loose clothing that may get caught in the chassis.

• When working under conditions that may be hazardous to your eyes, wear safety glasses.

Safety Precautions for Module Installation and Removal

Be sure to observe the following safety precautions when you work on the chassis.

Hardware Installation Guide for Cisco 8011-2X2XP4L PLE Service Endpoint Router

Safety Warnings

Safety Guidelines for Personal Safety and Equipment Protection

Statement 1006—Chassis Warning for Rack-Mounting and Servicing

To prevent bodily injury when mounting or servicing this unit in a rack, you must take special precautions to

ensure that the system remains stable. The following guidelines are provided to ensure your safety:

• This unit should be mounted at the bottom of the rack if it is the only unit in the rack.

• When mounting this unit in a partially filled rack, load the rack from the bottom to the top with the

heaviest component at the bottom of the rack.

• If the rack is provided with stabilizing devices, install the stabilizers before mounting or servicing the

unit in the rack.

Warning

Statement 1008—Class 1 Laser Product

This product is a Class 1 laser product.

Warning

Statement 1089—Instructed and Skilled Person Definitions

An instructed person is someone who has been instructed and trained by a skilled person and takes the necessary

precautions when working with equipment.

A skilled person or qualified personnel is someone who has training or experience in the equipment technology

and understands potential hazards when working with equipment.

There are no serviceable parts inside. To avoid risk of electric shock, do not open.

Warning

Statement 1090—Installation by Skilled Person

Only a skilled person should be allowed to install, replace, or service this equipment. See statement 1089 for

the definition of a skilled person.

There are no serviceable parts inside. To avoid risk of electric shock, do not open.

Warning

Safety with Electricity

Statement 1003—DC Power Disconnection

To reduce risk of electric shock or personal injury, disconnect DC power before removing or replacing

components or performing upgrades.

Warning

Hardware Installation Guide for Cisco 8011-2X2XP4L PLE Service Endpoint Router

Safety Warnings

Safety with Electricity

Tabla de contenidos

Otros manuales de Hardware de red de Cisco

Cisco

Cisco Firepower 9300 Manual

Cisco

Cisco o UCS X440p Instrucciones de instalación y mantenimiento

Cisco

Cisco NSS4100 - Gigabit Storage System Manual de instrucciones

Cisco

Cisco ASA Guía de inicio rápido

Cisco

Cisco IAD2430 Series Manual

Cisco

Cisco IronPort C670 Manual de usuario

Cisco

Cisco Meraki Catalyst 9300/X/L-M Series Manual de usuario

Cisco

Cisco C7200-I - Input/Output Controller - Control... Manual de usuario

Cisco

Cisco NSS2000 - Gigabit Storage System Chassis Cómo utilizar

Cisco

Cisco NTP-E157 Manual de lista de piezas

Cisco

Cisco ON100 Network Agent Manual de usuario

Cisco

Cisco Firepower 1010 Manual de usuario

Cisco

Cisco TELEPRESENCE MCU ACCESSING CONFERENCES - Manual de usuario

Cisco

Cisco OL-7822-06 Manual de usuario

Cisco

Cisco AIR-WLC2106-K9 - Wireless LAN Controller... Manual de usuario

Cisco

Cisco Catalyst 8300 Series Manual

Cisco

Cisco ME 1200 Series Manual

Cisco

Cisco CPS-MSP-1RU-K9 Manual de usuario

Cisco

Cisco FPR1150-ASA-K9 Manual

Cisco

Cisco CWDM-OADM 1 Series Guía de inicio rápido

Cisco

Cisco CiscoWorks Wireless LAN Solution Engine Manual del operador

Cisco

Cisco ATM Cable Interface Processor ACIP-SM(=) Manual del operador

Cisco

Cisco ONS 15310-MA SDH Manual

Cisco

Cisco NCS 1002 Manual de usuario

Manuales populares de Hardware de red de otras marcas

Matrix Switch Corporation

Matrix Switch Corporation MSC-HD161DEL Manual de usuario

B&B Electronics

B&B Electronics ZXT9-IO-222R2 Manual de usuario

Yudor

Yudor YDS-16 Manual de usuario

D-Link

D-Link ShareCenter DNS-320L Manual de usuario

Samsung

Samsung ES1642dc Instrucciones de uso

Honeywell Home

Honeywell Home LTEM-PV Instrucciones de montaje

evertz

evertz 7700 Series Manual de usuario

D-Link

D-Link ShareCenter DNS-343 Manual de usuario

Asante

Asante AsanteBridge 1012 Manual de usuario

FireBrick

FireBrick FB2700 Manual de usuario

Audiovox Electronics

Audiovox Electronics ARWH2T Manual de usuario

ADC

ADC DSX-1 Manual

NetComm

NetComm NF2 Manual de usuario

Alcatel-Lucent

Alcatel-Lucent 5620 Manual de usuario

Dell EMC

Dell EMC XC6420 Series Manual de usuario

Lanner

Lanner NCA-1020A Manual de usuario

Allied Telesis

Allied Telesis AT-TN121-A Manual de usuario

Arista

Arista CCA-ETM-Q12 Manual de usuario