Cisco FirePOWER 8000 Series Manual de usuario

Insert and Remove a Network Module (NetMod) on

an 8000 Series FirePOWER Appliance

Document ID: 118194

Contributed by Nazmul Rajib and Josiah Zimmermann, Cisco TAC

Engineers.

Aug 06, 2014

Contents

Introduction

Prerequisites

Before You Begin

Required Tool and Hardware

Remove the Module or Slot Cover

Insert a Module or Slot Cover

Introduction

Instead of the usual fixed port configuration of most high−end security appliances, the modularity of the 8000

Series appliances enables you to choose and change the number and type of interfaces for the appliance.

Various Network Modules (NetMods) are inserted into the 8000 Series appliances to customize the interface

configuration to match your network requirements. This document describes how to insert and remove a

NetMod in an 8000 series FirePOWER appliance.

Caution: If you install a NetMod in an incompatible slot on your appliance or a NetMod is otherwise

incompatible with your system, an error or warning message appears in the web interface on the managing

Defense Center when you attempt to configure the NetMod.

Prerequisites

Before You Begin

Before you begin, prepare to insert or remove your module using the following guidelines:

Identify all appliance and module parts.• Identify the slots where you want to install your NetMods.• Identify the correct slots for your stacking modules.• Confirm that the EMI gaskets are in place.• Unplug all power cords from the appliance.•

Warning: You cannot hot−swap modules. You must power down and unplug both power cords from the

appliance before inserting or removing modules.

Caution: Use proper electrostatic discharge (ESD) practices such as wearing wrist straps and using an ESD

work surface when handling the modules. Store unused modules in an ESD bag or box to prevent damage.

Required Tool and Hardware

T8 Torx screwdriver• 8000 Series FirePOWER appliance•

Remove the Module or Slot Cover

Step 1: Remove and reserve the T8 Torx screw from the lever of the module using the T8 Torx screwdriver.

Step 2: Pull the lever away from the module to release the latch.

Step 3: Slide the module out of the slot.

Insert a Module or Slot Cover

Step 1: Remove and reserve the T8 Torx screw from the lever of the module using the T8 Torx screwdriver.

Step 2: Pull the lever away from the module to open the latch. The near end of the latch is visible. The far

end of the latch is inside the module.

Step 3: Insert the module into the slot until the far end of the latch is inside the slot and the near end of the

latch touches the outside of the slot.

Step 4: Push the lever toward the module so that the latch engages and pulls the module into the slot.

Step 5: Press firmly on the screw hole to push the lever fully against the module to secure the latch.

Step 6: Insert and tighten the reserved T8 Torx screw into the lever.

Updated: Aug 06, 2014 Document ID: 118194

Tabla de contenidos

Otros manuales de Hardware de red de Cisco

Cisco

Cisco VIC-2FXS - 3600 Voice Interface Card-Fxs... Manual de instrucciones

Cisco

Cisco Versatile Interface Processor (VIP6-80)... Manual del operador

Cisco

Cisco Mc3810 - 16MB Flash Memory Guía rápida

Cisco

Cisco VIP-4R/4T Instrucciones de funcionamiento y mantenimiento

Cisco

Cisco AIM-VPN - DES/3DES VPN Data Encryption AIM... Manual de usuario

Cisco

Cisco 7606 Manual de usuario

Cisco

Cisco NCS 2002 Manual de instrucciones

Cisco

Cisco o UCS X440p Instrucciones de instalación y mantenimiento

Cisco

Cisco VPN 3002 Hardware Client Manager Manual de usuario

Cisco

Cisco ONS 15454 DWDM Manual de usuario

Cisco

Cisco NCS 1004 Manual de usuario

Cisco

Cisco ASA 5506-X Manual

Cisco

Cisco CWDM-OADM 1 Series Guía de inicio rápido

Cisco

Cisco 2650XM Manual de usuario

Cisco

Cisco ISA500 Series Manual de usuario

Cisco

Cisco ONS 15310-MA SDH Manual

Cisco

Cisco Nexus 3000 series Manual de usuario

Cisco

Cisco 5400 Series Manual de instrucciones

Cisco

Cisco WAVE-574-K9 - Wide Area Virtualization Engine... Manual

Cisco

Cisco 7246 - uBR Router Manual de usuario

Cisco

Cisco RSP4+ Bootflash Memory Upgrade to 16MB... Manual del operador

Cisco

Cisco AGS+ Manual de instrucciones

Cisco

Cisco NTP-E157 Manual de lista de piezas

Cisco

Cisco GS7000 Instrucciones de funcionamiento

Manuales populares de Hardware de red de otras marcas

Matrix Switch Corporation

Matrix Switch Corporation MSC-HD161DEL Manual de usuario

B&B Electronics

B&B Electronics ZXT9-IO-222R2 Manual de usuario

Yudor

Yudor YDS-16 Manual de usuario

D-Link

D-Link ShareCenter DNS-320L Manual de usuario

Samsung

Samsung ES1642dc Instrucciones de uso

Honeywell Home

Honeywell Home LTEM-PV Instrucciones de montaje

evertz

evertz 7700 Series Manual de usuario

D-Link

D-Link ShareCenter DNS-343 Manual de usuario

Asante

Asante AsanteBridge 1012 Manual de usuario

FireBrick

FireBrick FB2700 Manual de usuario

Audiovox Electronics

Audiovox Electronics ARWH2T Manual de usuario

ADC

ADC DSX-1 Manual

NetComm

NetComm NF2 Manual de usuario

Alcatel-Lucent

Alcatel-Lucent 5620 Manual de usuario

Dell EMC

Dell EMC XC6420 Series Manual de usuario

Lanner

Lanner NCA-1020A Manual de usuario

Allied Telesis

Allied Telesis AT-TN121-A Manual de usuario

Arista

Arista CCA-ETM-Q12 Manual de usuario