Cisco ONS 15454 M12 Manual de usuario

Maintaining the ONS 15454 M12 (ANSI and ETSI),

ONS 15454 M2 and ONS 15454 M6 Shelf

This chapter explains how to maintain the ONS 15454 (ANSI and ETSI), ONS 15454 M2 and ONS 15454

M6 shelf installations.

Unless otherwise specified, “ONS 15454” refers to both ANSI and ETSI M12 shelf assemblies.

Note

Due to memory limitations, TCC2/TCC2P cards are not supported as the node controller in multi-shelf

configuration from R10.5.2.6. Hence, it is recommended to use TCC3 card as the node controller in multi-shelf

configuration. However, the TCC2/TCC2P cards can be used as a subtended controller and also in a stand-alone

configuration.

Note

•NTP-G114 Inspect and Replace the Air Filter, on page 1

•NTP-G274 Replace the Air Filter of the ONS 15454 M2 Shelf Assembly, on page 5

•NTP-G262 Replace the Air Filter of the ONS 15454 M6 Shelf Assembly, on page 7

•NTP-G263 Replace the Air Filter of the AC Power Module in the ONS 15454 M6 Shelf Assembly, on

page 10

•NTP-G115 Clean Fiber Connectors, on page 11

•NTP-G40 Replace the Front Door , on page 14

•NTP-G116 Replace the Fan-Tray Assembly of the ONS 15454 Shelf Assembly, on page 16

•NTP-G272 Replace the Fan-Tray Assembly of the ONS 15454 M2 Shelf Assembly, on page 22

•NTP-G260 Replace the Fan-Tray Assembly of the ONS 15454 M6 Shelf Assembly, on page 24

•NTP-G117 Replace the ANSI Shelf Alarm Interface Panel, on page 26

•NTP-G118 Replace the ANSI Shelf Plastic Lower Backplane Cover, on page 29

•NTP-G795 Change System Mode Using LCD, on page 30

NTP-G114 Inspect and Replace the Air Filter

This procedure ensures that the air filter is free from dirt and dust, which allows

optimum air flow and prevents dirt and dust from entering the shelf.

Purpose

Maintaining the ONS 15454 M12 (ANSI and ETSI), ONS 15454 M2 and ONS 15454 M6 Shelf

New air filter, pinned hex key toolTools/Equipment

NonePrerequisite Procedures

As neededRequired/As Needed

OnsiteOnsite/Remote

NoneSecurity Level

Do not reach into a vacant slot or chassis while you install or remove a module or a fan. Exposed circuitry

could constitute an energy hazard. Statement 206

Warning

The air filters are single-use only. They must not be cleaned and reused. This is a Telcordia NEBS requirement,

GR-63-CORE Issue 4.

Note

Air filters must be inspected every month. If they are dirty or clogged with dust, they must be replaced with

a new air filter.

Note

If you install the air filter below 15454E-CC-FTA or 15454-CC-FTA, only filters with part numbers

700-23193-01 and 700-23194-01 can be used in this configuration.

Note

Although the air filter can work with older fan trays if it is installed with either side facing up, it is recommended

that you install it with the metal bracing facing up to preserve the surface of the filter. You must install the

air filter with the metal bracing facing up with 15454E-CC-FTA or 15454-CC-FTA.

Caution

To install the air filter inside the air ramp unit (15454E-AIR-RAMP or 15454-AIR-RAMP), use the ETSI

version of the air filter (15454-FTF2 or 15454E-FTF4).

Note

Procedure

Step 1 If the air filter is installed in the external filter brackets, slide the filter out of the brackets while being careful

not to dislodge any dust that might have collected on the filter and proceed to Step 8. Figure 1: ANSI Shelf

Fan-Tray Air Filter in an External Filter Bracket (Front Door Removed), on page 3 shows the fan-tray air

filter in an external filter bracket on an ANSI shelf. Figure 2: ETSI Shelf Fan-Tray Air Filter in an External

Maintaining the ONS 15454 M12 (ANSI and ETSI), ONS 15454 M2 and ONS 15454 M6 Shelf

NTP-G114 Inspect and Replace the Air Filter

Filter Bracket (Front Door Removed), on page 4 shows the fan-tray air filter in an external filter bracket on

an ETSI shelf.

Step 2 If the filter is installed below the fan tray and not in the external filter brackets, open the front door of the

shelf assembly. If the front door is already open, proceed to Step 3.

a) Open the front door lock.

The ONS 15454 comes with a pinned hex key for locking and unlocking the front door. Turn the key

counterclockwise to unlock the door and clockwise to lock it.

b) Press the door button to release the latch.

c) Swing the door open.

Step 3 (Optional) Remove the front door using the DLP-G10 Remove the Front Door. If you do not want to remove

the door or it is already removed, proceed to Step 4.

Figure 1: ANSI Shelf Fan-Tray Air Filter in an External Filter Bracket (Front Door Removed)

Maintaining the ONS 15454 M12 (ANSI and ETSI), ONS 15454 M2 and ONS 15454 M6 Shelf

NTP-G114 Inspect and Replace the Air Filter

Figure 2: ETSI Shelf Fan-Tray Air Filter in an External Filter Bracket (Front Door Removed)

Step 4 Push the outer side of the handles on the fan-tray assembly to expose the handles.

Step 5 Pull the handles and slide the fan-tray assembly one half inch (12.7 mm) out of the shelf assembly and wait

until the fans stop.

Step 6 When the fans have stopped, pull the fan-tray assembly completely out of the shelf assembly.

Step 7 Gently remove the air filter from the shelf assembly. Be careful not to dislodge any dust that might have

collected on the filter.

Step 8 Visually inspect the air filter material for dirt and dust.

Step 9 Replace the air filter with a new one if the air filter is dirty or clogged with dust.

Do not leave the fan tray out of the chassis for an extended period of time because excessive heat

can damage the ONS 15454 cards.

Caution

Step 10 Replace the air filter:

a) If the air filter is installed in the external filter brackets, slide the new air filter all the way to the back of

the brackets.

b) If the filter is installed below the fan-tray assembly, slide the new air filter into the recessed compartment

at the bottom of the shelf assembly. Put the front edge of the air filter flush against the front edge of the

recessed compartment. Push the fan tray back into the shelf assembly.

If the fan tray does not slide all the way to the back of the shelf assembly, pull the fan tray out

and readjust the position of the air filter until the fan tray fits correctly.

Caution

On a powered-up ONS 15454, the fans start immediately after the fan-tray assembly is correctly

inserted.

Note

Step 11 To verify that the tray is plugged into the backplane, ensure that the LCD on the front of the fan-tray assembly

is activated and displays node information.

Step 12 Rotate the retractable handles back into their compartments.

Maintaining the ONS 15454 M12 (ANSI and ETSI), ONS 15454 M2 and ONS 15454 M6 Shelf

NTP-G114 Inspect and Replace the Air Filter

Step 13 If you removed the door, complete the NTP-G40 Replace the Front Door , on page 14. If not, close and lock

the door.

Stop. You have completed this procedure.

NTP-G274 Replace the Air Filter of the ONS 15454 M2 Shelf

Assembly

This procedure replaces the air filter of the ONS 15454 M2 shelf assembly.Purpose

New air filterTools/Equipment

•NTP-G266 Install the ONS 15454 M2 Shelf

• Connect the chassis to the office ground. For detailed instructions on how

to ground the chassis, refer to the Electrostatic Discharge and Grounding

Guide for Cisco CPT and Cisco ONS Platforms.

Prerequisite Procedures

As NeededRequired/As Needed

RemoteOnsite/Remote

Provisioning or higherSecurity Level

The air filters are single-use only. They must not be cleaned and reused. This is a Telcordia NEBS requirement,

GR-63-CORE Issue 4.

Note

Air filters must be inspected every month. If they are dirty or clogged with dust, they must be replaced with

a new air filter.

Note

Procedure

Step 1 Untighten the screw on the air-filter (see the following figure).

Maintaining the ONS 15454 M12 (ANSI and ETSI), ONS 15454 M2 and ONS 15454 M6 Shelf

NTP-G274 Replace the Air Filter of the ONS 15454 M2 Shelf Assembly

Figure 3: Replacing the Air Filter

Screw2Air filter1

Step 2 Extract the air filter from the shelf assembly as shown in the following figure.

Figure 4: Replacing the Air Filter

Filter grid2Air filter1

Step 3 Separate the cable guides from the air filter as shown in the following figure.

Maintaining the ONS 15454 M12 (ANSI and ETSI), ONS 15454 M2 and ONS 15454 M6 Shelf

NTP-G274 Replace the Air Filter of the ONS 15454 M2 Shelf Assembly

Figure 5: Replacing the Air Filter

Step 4 Replace the air filter with a new one if the air filter is dirty or clogged with dust.

Step 5 Attach the cable guide and insert the air filter into the shelf assembly.

The air filter must be inserted with the grid facing the shelf assembly as shown in Figure 5: Replacing

the Air Filter, on page 7.

Note

Step 6 Tighten the screw on the air-filter.

Stop. You have completed this procedure.

NTP-G262 Replace the Air Filter of the ONS 15454 M6 Shelf

Assembly

This procedure replaces the air filter of the ONS 15454 M6 shelf assembly.Purpose

New air filterTools/Equipment

•NTP-G252 Install the ONS 15454 M6 Shelf

• Connect the chassis to the office ground. For detailed instructions on how

to ground the chassis, refer to the Electrostatic Discharge and Grounding

Guide for Cisco CPT and Cisco ONS Platforms .

Prerequisite Procedures

As NeededRequired/As Needed

RemoteOnsite/Remote

Provisioning or higherSecurity Level

Maintaining the ONS 15454 M12 (ANSI and ETSI), ONS 15454 M2 and ONS 15454 M6 Shelf

NTP-G262 Replace the Air Filter of the ONS 15454 M6 Shelf Assembly

The air filters are single-use only. They must not be cleaned and reused. This is a Telcordia NEBS requirement,

GR-63-CORE Issue 4.

Note

Air filters must be inspected every month. If they are dirty or clogged with dust, they must be replaced with

a new air filter.

Note

Procedure

Step 1 Open the front door of the shelf assembly (see NTP-G259 Open and Remove the Standard Door of the ONS

15454 M6 Shelf). If the shelf assembly does not have a front door, continue with Step 3.

Step 2 (Optional) Complete the DLP-G577 Remove the Standard Door of the ONS 15454 M6 Shelf to remove the

front door. If you do not want to remove the door, proceed to Step 3.

Step 3 Push the retention feature present on the right side of the shelf assembly to the left side (see the following

figure).

Figure 6: Replacing the Air Filter

Step 4 Extract the air filter from the shelf assembly (see the following figure).

Maintaining the ONS 15454 M12 (ANSI and ETSI), ONS 15454 M2 and ONS 15454 M6 Shelf

NTP-G262 Replace the Air Filter of the ONS 15454 M6 Shelf Assembly

Figure 7: Extracting the Air Filter

Step 5 Replace the air filter with a new one if the air filter is dirty or clogged with dust.

Step 6 Insert the air filter into the shelf assembly (see Figure 7: Extracting the Air Filter, on page 9).

The air filter must be inserted with the grid facing the shelf assembly as shown in Figure 7: Extracting

the Air Filter, on page 9.

Note

Step 7 Push the retention feature to the right side (see the following figure).

Figure 8: Replacing the Air Filter

Step 8 Close the front door. If you removed the door, complete the NTP-G258 Install the Standard Door of the ONS

15454 M6 Shelf.

Maintaining the ONS 15454 M12 (ANSI and ETSI), ONS 15454 M2 and ONS 15454 M6 Shelf

NTP-G262 Replace the Air Filter of the ONS 15454 M6 Shelf Assembly

Stop. You have completed this procedure.

NTP-G263 Replace the Air Filter of the AC Power Module in the

ONS 15454 M6 Shelf Assembly

This procedure replaces the air filter of the AC power module in the ONS 15454

M6 shelf assembly.

Purpose

New air filterTools/Equipment

•NTP-G252 Install the ONS 15454 M6 Shelf

• Connect the chassis to the office ground. For detailed instructions on how

to ground the chassis, refer to the Electrostatic Discharge and Grounding

Guide for Cisco CPT and Cisco ONS Platforms .

•DLP-G569 Install the AC Power Module in the ONS 15454 M6 Shelf

Prerequisite Procedures

As NeededRequired/As Needed

RemoteOnsite/Remote

Provisioning or higherSecurity Level

The air filters are single-use only. They must not be cleaned and reused. This is a Telcordia NEBS requirement,

GR-63-CORE Issue 4.

Note

Air filters must be inspected every month. If they are dirty or clogged with dust, they must be replaced with

a new air filter.

Note

Procedure

Step 1 Open the front door of the shelf assembly (see DLP-G576 Open the Standard Door of the ONS 15454 M6

Shelf). If the shelf assembly does not have a front door, continue with Step 3.

Step 2 (Optional) Complete the DLP-G577 Remove the Standard Door of the ONS 15454 M6 Shelf to remove the

front door. If you do not want to remove the door, proceed to Step 3.

Step 3 Remove the air filter on the AC power module (see Figure 6: Replacing the Air Filter, on page 8).

Maintaining the ONS 15454 M12 (ANSI and ETSI), ONS 15454 M2 and ONS 15454 M6 Shelf

NTP-G263 Replace the Air Filter of the AC Power Module in the ONS 15454 M6 Shelf Assembly

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Hardware de red de Cisco

Cisco

Cisco SA-VAM - VPN Acceleration Module Manual del operador

Cisco

Cisco Linksys WES610N Manual de usuario

Cisco

Cisco SCE 2000 4/8xFE Manual de usuario

Cisco

Cisco GS7000 Instrucciones de funcionamiento

Cisco

Cisco ASR 901S Series Instrucciones de funcionamiento

Cisco

Cisco CGR 1000 Series Manual de usuario

Cisco

Cisco ONS 15600 Manual de usuario

Cisco

Cisco ASA Guía de inicio rápido

Cisco

Cisco TelePresence Manual de servicio

Cisco

Cisco C8510MSR-SKIT-DC - Catalyst 8510 Multiservice Switch... Manual de usuario

Cisco

Cisco WAVE-574-K9 - Wide Area Virtualization Engine... Manual

Cisco

Cisco 1230AG - Aironet - Wireless Access Point Manual de usuario

Cisco

Cisco MERAKI MX75 Manual de usuario

Cisco

Cisco GS7000 Instrucciones de funcionamiento

Cisco

Cisco Cisco ONS 15600 SDH Manual de usuario

Cisco

Cisco Versatile Interface Processor (VIP6-80)... Manual del operador

Cisco

Cisco IPS 7.1 Manual de usuario

Cisco

Cisco 5400 Manual de usuario

Cisco

Cisco ONS 15454 SDH E1-75 Manual de usuario

Cisco

Cisco Firepower 9300 Manual

Cisco

Cisco ONS 15454 SDH E1-75 Manual de usuario

Cisco

Cisco PRISMA II XD Manual de usuario

Cisco

Cisco ESR-PRE2 Manual de usuario

Cisco

Cisco AIM-VPN - DES/3DES VPN Data Encryption AIM... Manual de usuario

Manuales populares de Hardware de red de otras marcas

Matrix Switch Corporation

Matrix Switch Corporation MSC-HD161DEL Manual de usuario

B&B Electronics

B&B Electronics ZXT9-IO-222R2 Manual de usuario

Yudor

Yudor YDS-16 Manual de usuario

D-Link

D-Link ShareCenter DNS-320L Manual de usuario

Samsung

Samsung ES1642dc Instrucciones de uso

Honeywell Home

Honeywell Home LTEM-PV Instrucciones de montaje

evertz

evertz 7700 Series Manual de usuario

D-Link

D-Link ShareCenter DNS-343 Manual de usuario

Asante

Asante AsanteBridge 1012 Manual de usuario

FireBrick

FireBrick FB2700 Manual de usuario

Audiovox Electronics

Audiovox Electronics ARWH2T Manual de usuario

ADC

ADC DSX-1 Manual

NetComm

NetComm NF2 Manual de usuario

Alcatel-Lucent

Alcatel-Lucent 5620 Manual de usuario

Dell EMC

Dell EMC XC6420 Series Manual de usuario

Lanner

Lanner NCA-1020A Manual de usuario

Allied Telesis

Allied Telesis AT-TN121-A Manual de usuario

Arista

Arista CCA-ETM-Q12 Manual de usuario