Cisco Octal-Port DMT ATU-C Line Card Manual técnico

Cisco IOS Release 12.1(6)DA

Octal-Port DMT ATU-C Line Card

This feature module describes the Cisco IOS support for the octal-port DMT ATU-C (8xDMT) line card.

It includes information on new and modified commands.

This document includes the following sections:

•Feature Overview, page 1

•Supported Platforms, page 4

•Supported Standards, MIBs, and RFCs, page 5

•Prerequisites, page 6

•Configuration Tasks, page 6

•Configuration Examples, page 9

•Command Reference, page 10

•Glossary, page 27

Feature Overview

The 8xDMT line card provides higher port density for the Cisco 6015, Cisco 6160, and Cisco 6260. This

line card:

•Supports eight ADSL modem connections per card.

•Converts ADSL modulation from the line card into digital data streams to and from the NI-2 card.

•Negotiates the line rate with the customer premises equipment (CPE) when it trains and bases the

rate on line quality and distance.

•Provides subscriber and port provisioning through DSL profiles.

–

Allows single latency—Fast or interleaved path selection.

–

Supports trellis encoding.

–

Supports bit swapping.

•Interoperates with certain CPE. For more detailed information, see the “Supported Platforms”

section on page 4.

Note Check with a Cisco customer representative to verify CPE compatibility with

the 8xDMT.

Octal-Port DMT ATU-C Line Card

Feature Overview

Cisco IOS Release 12.1(6)DA

Benefits

G.hs Support (ITU G.994.1)

G.hs support is provided through both the MIB and the CLI. Features from G.hs that are

supported include:

•Enabling/disabling all or one of the following modes.

–

G.dmt

–

T1.413 Issue 2

–

G.lite

•Setting auto mode defers the mode selection to the ATU-R.

•Displaying current mode/capability.

Bit Swapping

Bit swapping is a mechanism that allows DMT transceivers to reallocate bits between carriers and adjust

gain scaling based on the carrier SNR margin.

Fast or Interleaved Path Selection

The fast path feature allows you to configure either the fast or the interleave path via DSL profile

configuration commands provided that the CPE also supports fast path. You can use either the interleave

or fast path with the 8xDMT line card provided that the CPE also supports fast path. The fast path

provides improved latency characteristics for applications that cannot tolerate latency (for

example, voice).

The parameters for either path are configurable using the DSL profile configuration commands. Note that

although you can configure both paths, only one path will actually be enabled (dual latency is not

supported at this time). Thus the maximum bit rates for the unused path must be zero. For example, to

configure and use the fast path, you must specify nonzero maximum bit rates for the fast path. Once you

configure the maximum bit rates for the fast path, the rates for the interleave path must be zero. The IOS

software ensures that only one path is enabled at a given time.

Trellis Encoding

Trellis encoding is a method of providing better performance in a noisy environment. The end result of

using Trellis encoding is that you can transmit at faster line rates with lower error rates, thus providing

a faster overall throughput in a moderately noisy environment. You can enable or disable trellis encoding

for a specific DSL profile.

Enhanced Line Quality Monitoring and Management

The 8xDMT improves the manageability of DMT ports on supported DSLAMs. The following

commands are used to configure this functionality:

•dmt minrate-blocking

DMT minrate-blocking customizes the DMT port reaction to lines that train below configured

minimum bit rates. Formerly, if a line trained below the configured minimum bit rate threshold, it

would generate a minor alarm, but the DMT port remained active. The dmt minrate-blocking

prevents DMT ports from training when bit rates fall below the configured minimum threshold

specified in the dmt bitrate minimum command.

Octal-Port DMT ATU-C Line Card Feature Overview

Cisco IOS Release 12.1(6)DA

Note The original option, which generates a minor alarm when configured minimum bit rates are

not met, is configured by default in DSL profiles. The default configuration is no dmt

minrate-blocking.

•dmt rate-adaptation

The dmt rate-adaptation command monitors the signal-to-noise ratio (SNR) on DSL lines. When

enabled, software monitors the upstream and downstream DMT ports for low SNR margins. When

the actual upstream or downstream margin falls below the dmt rate-adaptation margin for the

duration of the configured rate-adaptation interval, the line drops and attempts to retrain. If the

line is able to retrain, it trains to a lower bit rate with improved SNR margins.

Restrictions

The 8xDMT card is not spectrally compatible with SDSL, G.shdsl, or IDSL. Place these cards in a

separate chassis half when using them in the same chassis as 8xDMT line cards.

Related Features and Technologies

The 8xDMT line card is an upgrade of the 4xDMT (6260) and 4xFlexi (6160, 6260, 6015) line cards.

Related Documents

Hardware Documents

A complete list of all DSL hardware product related documentation is available on the World Wide Web

at http://www.cisco.com/univercd/cc/td/doc/product/dsl_prod/index.htm.

Software Documents

A complete list of all DSL IOS software product related documentation is available on the World Wide

Web at http://www.cisco.com/univercd/cc/td/doc/product/dsl_prod/ios_dsl/index.htm.

In the ATM software product related documentation, look for information pertaining to the

Cisco LightStream 1010, which uses the same software base as the NI-2 DSL systems. This

documentation is available on the World Wide Web at

http://www.cisco.com/univercd/cc/td/doc/product/atm/index.htm.

Octal-Port DMT ATU-C Line Card

Supported Platforms

Cisco IOS Release 12.1(6)DA

Supported Platforms

DSLAMs

This feature supports the 8xDMT line card on the Cisco 6015, Cisco 6160, and Cisco 6260 platforms

with NI-2. Table 1details the total available ADSL modem connections for each chassis.

The 8xDMT is designed for use with the Cisco 6015, Cisco 6160, or Cisco 6260 chassis in one of the

following configurations:

•Cisco 6015, Cisco 6160, or Cisco 6260 with a POTS splitter chassis—Provisions one modem

directly and is physically connected to one specific subscriber line through the POTS

splitter chassis.

•Cisco 6015, Cisco 6160, or Cisco 6260 without a POTS splitter chassis—Provisions one modem

directly and is physically connected to one specific subscriber line through the main distribution

frame (MDF) connections.

CPE

•Cisco 677

•Cisco 678

•Cisco Soho 77

•Cisco 827

•Cisco IAD 2423

•Cisco 1700, Cisco 2600, and Cisco 3600 series with ADSL WIC

•Alcatel Speed Touch Home

•Alcatel Speed Touch Pro

•Efficient Networks 5260 and 5262

•Westell modems based on Alcatel Microelectronics firmware version 1.4.1

•CPE using ADI chipsets with firmware versions 0X3019BE70 (Version 3.0),

0X2219BE04 (Version 2.2), or 0X2019BE2D (Version 2.0) should operate similar to the Cisco 677

Note A correct firmware version does not guarantee interoperation with third-party CPE. Some

hardware variations can affect performance and error rates. Test the interoperation of CPE

with the 8xDMT in the targeted deployment model before provisioning service.

Table 1 Number of Available Modem Connections for Each Chassis

Chassis Number of Available 8xDMT

Slots Total ADSL Modem Connections

Cisco 6015 6 48

Cisco 6160 32 256

Cisco 6260 30 240

Octal-Port DMT ATU-C Line Card Supported Standards, MIBs, and RFCs

Cisco IOS Release 12.1(6)DA

Supported Standards, MIBs, and RFCs

Standards

•ANSI T1.413-Issue 2, Category 1 only

•ANSI T1.413-Issue 2, Annex F (Reduced NEXT)

•Universal Test & Operations PHY for ATM, Level 2; A standard for transport of ATM cells over a

16-bit parallel data bus. See ATM Forum document af-phy-0039.000.

•ITU G.992.1, Annex A (G.dmt)

•ITU G.992.2. (G.lite)

•ITU G.994.1. (G.hs)

Standard MIBS

To obtain lists of supported MIBs by platform and Cisco IOS release and to download MIB modules, go

to the Cisco MIB web site on Cisco Connection Online (CCO) at

http://www.cisco.com/public/sw-center/netmgmt/cmtk/mibs.shtml.

•IETF RFC 1695, Definitions of Managed Objects for ATM Management Version 8.0 using SMIv2

•IETF RFC 2662, Definitions of Managed Objects for the ADSL Line (obsoletes ADSL Forum TR-

006, SNMP-based ADSL Line MIB)

–

Objects not supported for 8xDMT:

From AdslLineConfProfileEntry - adslAtucConfRateChanRatio, adslAtucConfMaxSnrMgn,

adslAtucConfUpshiftSnrMgn, adslAturConfRateChanRatio, adslAturConfMaxSnrMgn,

adslAturConfUpshiftSnrMgn,adslAturConfMinUpshiftTime.

AdslLineAlarmConfProfileEntry

•ADSL Forum TR-014, DMT Line Code Specific MIB

–

Objects not supported for 8xDMT:

FromAdslLineDmtConfProfileEntry- adslAtucDmtConfFreqBins, adslAturDmtConfFreqBins,

adslAtucDmtConfInterleavePath,adslAtucDmtConfFastPath,adslAturDmtConfInterleavePath,

adslAturDmtConfFastPath.

Cisco-Derived MIBS

•CISCO-ADSL-LINE-MIB

–

Objects not supported for DMT8:

•CISCO-ADSL-DMT-LINE-MIB

–

Objects not supported for DMT8:

From the cAdslDmtLineConfProfileGroup cAdslAtucDmtConfBitSwapEnabled,

cAdslAtucDmtConfBitSwapFrom, cAdslAtucDmtConfBitSwapTo. You can set these objects

via SNMP, however, the 8xDMT cards will ignore these objects when provisioning ports

for service.

To obtain lists of supported MIBs by platform and Cisco IOS release and to download MIB modules, go

to the Cisco MIB web site on Cisco Connection Online (CCO) at

http://www.cisco.com/public/sw-center/netmgmt/cmtk/mibs.shtml.

Octal-Port DMT ATU-C Line Card

Prerequisites

Cisco IOS Release 12.1(6)DA

Prerequisites

To use the 8xDMT feature, you must have one of the following DSLAMs with the 8xDMT line card, and

IOS 12.1(6) or above installed:

•Cisco 6015

•Cisco 6160

•Cisco 6260

Configuration Tasks

See the following sections for configuration tasks for the 8xDMT feature. Each task in the list indicates

if the task is optional or required.

•Preprovisioning the 8xDMT Line Card, page 6 (optional)

•Creating and Associating a DSL Profile with Each Port, page 7 (required)

•Modifying the DSL Profile, page 7 (optional)

Preprovisioning the 8xDMT Line Card

Starting at the global configuration prompt, use the following commands to preprovision a slot for use

with the 8xDMT line card:

Tips After you have completed these steps, insert the 8xDMT line card to activate the card with your

preprovisioned configuration.

Verifying the Preprovisioned Slot

Use the show running-configuration command to verify that you preprovisioned the slot correctly.

Command Purpose

Step 1 DSLAM(config)# slot 1 ATUC-1-DMT8 This command associates the 8xDMT line card with

the specified slot.

Step 2 DSLAM(config)# dsl-profile 8xDMT Creates and names the DSL profile, 8xDMT in

this example.

Step 3 DSLAM(config-dsl-prof)# exit Return to the global configuration prompt.

Step 4 DSLAM(config)# interface atm1/1 Enter interface configuration mode on the port

where you will associate the 8xDMT DSL profile.

Repeat this process on each port that you wish to

associate with a DSL profile.

Step 5 DSLAM(config-if)# dsl profile 8xDMT Associates the DSL profile named 8xDMT with

atm interface 1/1.

Step 6 DSLAM(config-if)# exit Return to the global configuration prompt.

Octal-Port DMT ATU-C Line Card Configuration Tasks

Cisco IOS Release 12.1(6)DA

Creating and Associating a DSL Profile with Each Port

Before starting this configuration task, install the 8xDMT line card. Refer to the Octal-Port DMT ATU-C

Line Card FRU Installation and Configuration Notes for information on installing the 8xDMT line card.

Starting at the global configuration prompt, use the following procedure to associate a DSL profile with

a port:

Verifying the DSL Profiles

You can use the show dsl profile profile-name command to verify that a DSL profile is attached to a port.

You can also use the show running-configuration command to verify that the DSL profile is associated

with a port.

Tips If no DSL profile appears in the show running-configuration command output, the default

DSL profile is enabled. See the “Command Reference” section on page 10 for the default

configuration values.

Modifying the DSL Profile

Starting at the global configuration prompt, use the following procedure to modify the default bit rate,

signal-to-noise ratio, DMT check bytes, and overhead framing parameters in your DSL profile:

Caution Before migrating from interleave mode to fast path, determine whether the deployed CPEs offer

support for the feature. The Cisco 600 series CPEs currently do not support fast path.

Command Purpose

Step 1 DSLAM(config)# dsl-profile 8xDMT Select the profile that you want to attach to the

selected port. The profile name 8xDMT is used as

an example.

Step 2 DSLAM(config-dsl-prof)# exit Return to the global configuration prompt.

Step 3 DSLAM(config)# interface atm1/1 Enter interface configuration mode on the port

where you will associate the 8xDMT DSL profile.

Repeat this process on each port that you wish to

associate with a DSL profile.

Step 4 DSLAM(config-if)# dsl-profile 8xDMT Associate the DSL profile 8xDMT with

atm interface 1/1.

Step 5 DSLAM(config-if)# exit Return to the global configuration prompt.

Command Purpose

Step 1 DSLAM(config)# dsl-profile 8xDMT Enter DSL profile configuration mode.

Step 2 DSLAM(config-dsl-profile)# dmt bitrate

maximum fast downstream 3200 upstream 640 Set a DMT bit rate of 3200 kbps downstream and 640 kbps

upstream on the fast path. Automatically configures the

interleaved path to 0 kbps.

Octal-Port DMT ATU-C Line Card

Monitoring and Maintaining the 8xDMT Line Card

Cisco IOS Release 12.1(6)DA

Troubleshooting Tips

Cisco provides Cisco.com as a starting point for all technical assistance. Customers and partners can

obtain documentation, troubleshooting tips, and sample configurations from online tools.

For Cisco.com registered users, additional troubleshooting tools are available from the TAC website. To

obtain troubleshooting help, go to the Cisco Troubleshooting Assistant web site on Cisco Connection

Online (CCO) at:

http://www.cisco.com/kobayashi/support/tac/tsa/dslstep.html

Also see the “Monitoring and Maintaining the 8xDMT Line Card” section on page 8.

Monitoring and Maintaining the 8xDMT Line Card

Use the following commands to monitor and maintain the 8xDMT line card:

Step 3 DSLAM(config-dsl-profile)# dmt

check-bytes fast downstream 0 upstream 0 Set the upstream and downstream FEC check (redundancy) bytes

to 0.

Step 4 DSLAM(config-dsl-profile)# dmt margin

downstream 12 upstream 6 Set the downstream and upstream signal-to-noise ratio (SNR)

margins for a DSL profile.

Step 5 DSLAM(config-dsl-profile)# dmt

overhead-framing mode1 Set the overhead framing mode, in this example to 1.

Step 6 DSLAM(config-dsl-profile)# exit Return to the global configuration prompt.

Command Purpose

DSLAM# show dsl interface atm s

lot/port

DSLAM# show dsl status DMT

These commands display basic information about the DSL link,

including port status, dsl statistics, line errors, and cards detected.

DSLAM# show facility-alarm status The show facility-alarm status command displays all of the current

major and minor alarms and the user-configurable alarm thresholds

for temperature. After an alarm condition is indicated (by LEDs or

bells), you can use the show facility-alarm status command to

determine the cause of the alarm.

Note You must turn on the alarms in the profile for alarms to

be displayed.

DSLAM# show hardware The show hardware command shows information on each of the

slots in your chassis. It tells whether line cards, fan trays, and PEMs

are present.

Octal-Port DMT ATU-C Line Card Configuration Examples

Cisco IOS Release 12.1(6)DA

Configuration Examples

The following example shows a profile named 8xDMT2 being created. The profile uses the default

profile values for any parameters not specified.

Current configuration : 7019 bytes

version 12.1

no service pad

service timestamps debug uptime

service timestamps log uptime

no service password-encryption

hostname DSLAM

boot system flash:ni2-dsl-mz.121-6.DA.bin

slot 1 ATUC-4FLEXIDMT

slot 2 ATUC-1-DMT8

slot 3 ATUC-4FLEXIDMT

slot 4 ATUC-4FLEXIDMT

slot 5 ATUC-4FLEXIDMT

slot 6 ATUC-4FLEXIDMT

enable password cisco

dsl-profile default

dmt bitrate maximum interleaved downstream 8032 upstream 864

cap bitrate maximum downstream 7168 upstream 1088

dsl-profile 8xdmt

dsl-profile 8xDMT2

dmt overhead-framing mode1

dmt check-bytes fast downstream 12 upstream 6

dmt margin downstream 12 upstream 6

dmt bitrate maximum fast downstream 3200 upstream 640

dmt bitrate maximum interleaved downstream 0 upstream 0

network-clock-select 1 system

ip subnet-zero

ip host-routing

no ip finger

Octal-Port DMT ATU-C Line Card

Command Reference

Cisco IOS Release 12.1(6)DA

Command Reference

This section documents the new and modified commands that are specific to the8xDMT feature. All

other commands used with this feature are documented in the Command Reference for Cisco DSLAMS

with NI-2. For information on other Cisco IOS commands that can be used on the NI-2 DSL systems,

see the Cisco ATM Switch Router Command Reference Guide.

Tabla de contenidos

Otros manuales de Hardware de red de Cisco

Cisco

Cisco Firepower 1010 Manual de usuario

Cisco

Cisco S170 Web Manual de usuario

Cisco

Cisco Linksys NSLU2 Manual de usuario

Cisco

Cisco 2610 - Router - EN Manual de usuario

Cisco

Cisco Meraki Catalyst 9300/X/L-M Series Manual de usuario

Cisco

Cisco Cisco ONS 15600 SDH Manual de usuario

Cisco

Cisco ISA550 Manual de instrucciones

Cisco

Cisco NCS 2000 series Manual de usuario

Cisco

Cisco SA-VAM - VPN Acceleration Module Manual del operador

Cisco

Cisco CVPN3002-K9 - Fast Ethernet VPN Gateway Manual de usuario

Cisco

Cisco CMX 3375 Manual de usuario

Cisco

Cisco ONS 15200 Series Manual de usuario

Cisco

Cisco CTM GateWay Guía de instalación

Cisco

Cisco Physical Access 1125 Appliance Manual de usuario

Cisco

Cisco ONS 15310-CL Manual de usuario

Cisco

Cisco CX-TRIP2 Manual del operador

Cisco

Cisco ASA 5506-X Manual

Cisco

Cisco Meraki MX68 Manual

Cisco

Cisco OSM-12CT3/T1 - Optical Services Module... Guía rápida

Cisco

Cisco CSS11501 - 100Mbps Ethernet Load Balancing... Manual de usuario

Cisco

Cisco ONS 15454 M12 Manual de usuario

Cisco

Cisco OL-7822-06 Manual de usuario

Cisco

Cisco CGR 1240 Manual de usuario

Cisco

Cisco Catalyst 8510 Manual de usuario

Manuales populares de Hardware de red de otras marcas

Matrix Switch Corporation

Matrix Switch Corporation MSC-HD161DEL Manual de usuario

B&B Electronics

B&B Electronics ZXT9-IO-222R2 Manual de usuario

Yudor

Yudor YDS-16 Manual de usuario

D-Link

D-Link ShareCenter DNS-320L Manual de usuario

Samsung

Samsung ES1642dc Instrucciones de uso

Honeywell Home

Honeywell Home LTEM-PV Instrucciones de montaje

evertz

evertz 7700 Series Manual de usuario

D-Link

D-Link ShareCenter DNS-343 Manual de usuario

Asante

Asante AsanteBridge 1012 Manual de usuario

FireBrick

FireBrick FB2700 Manual de usuario

Audiovox Electronics

Audiovox Electronics ARWH2T Manual de usuario

ADC

ADC DSX-1 Manual

NetComm

NetComm NF2 Manual de usuario

Alcatel-Lucent

Alcatel-Lucent 5620 Manual de usuario

Dell EMC

Dell EMC XC6420 Series Manual de usuario

Lanner

Lanner NCA-1020A Manual de usuario

Allied Telesis

Allied Telesis AT-TN121-A Manual de usuario

Arista

Arista CCA-ETM-Q12 Manual de usuario