Cisco Edge 300 Series Guía de inicio rápido

Last updated on October 15, 2015

Edge300FirmwareUpgrade

Introduction

This guide outlines the steps to upgrade the firmware on the Cisco Edge 300 and will be described in two

stages:

Preparing a bootable USB drive containing the desired Edge 300 firmware

Flashing the firmware onto the Edge 300 device

Prerequisites

Cisco Edge 300 device

1 USB flash drive formatted in FAT32 file system (minimum 2GB free space)

1 Edge 300 firmware image file (for use with the USB flash drive)

1 paper clip / SIM eject tool (for the recessed reset button)

Note:

Empty the contents of the USB flash drive for the purpose of Edge firmware flashing. The process

of creating a bootable flash drive will temporarily render it unusable for conventional storage and

transferring of files. The flash drive can later be reformatted back to its original file system once the

firmware upgrade has completed.

PreparingaBootableUSBDrive

1. From your computer, copy the Edge 300 firmware image into the root directory of the USB flash

drive. Disconnect the USB drive from your computer and connect it to the USB port of the Edge 300,

located on the side of the device.

2. SSH into the device using either PuTTy (on a Windows PC) or Terminal (on a Mac) using the

commands shown below. Replace {device IP} with the actual IP address of the Edge device. (verify

with your network administrator regarding the correct IP address and root credentials for the Edge

300).

3. Use the blkid command to locate the USB drive. (usually /dev/sdxx with xx being b1, b2 or c1, c2

etc.) For this guide, we will assume it is /dev/sdb1.

4. Mount the USB drive.

5. Unmount the USB drive. Copy the firmware image onto the Edge 300 device (into the /apps/

directory). Wait for the task to finish. The copying of the image file will be completed when the

console displays a # symbol at the beginning of the command line.

6. Without ejecting your USB drive, run the following commands (remember to replace sdb1 with your

blkid if discovered to be different from Step 3). Note that each command will take some time to

execute. Wait until each command has completed (console displays a #) before proceeding to the

next command. When all commands have been executed, remove the USB drive from the device.

#sshroot@{deviceIP}

#root@{deviceIP}password:cisco

#blkid

/dev/sdb1:LABEL="USBDRIVE"UUID="7288-0792"TYPE="vfat"

#mount/dev/sdb1/tmp/mnt

#cp/tmp/mnt/smi-usb-sunbird-1.5.0-delivery.tar.gz/apps/

#umount/tmp/mnt

FlashingtheFirmware

1. Press and hold the power button on the Edge 300 to turn it OFF. Connect the newly created

bootable USB drive into the USB port again, located on the side of the device.

2. Press and hold the power button on the Edge 300 to turn it back ON. Using your paper clip / SIM

eject tool, press and hold the reset button located next to the power button of the device for about 5

seconds until the device reboots itself.

#mkfs.ext3/dev/sdb1

#mount/dev/sdb1/tmp/mnt

#tarxvzf/apps/smi-usb-sunbird-1.5.0-delivery.tar.gz–C/tmp/mnt/

#umount/tmp/mnt

3. Once rebooted, the Edge 300 device will read the contents of the USB drive and begin flashing the

firmware. The power LED will be flashing continuously at this point, indicating the firmware update is

in process. The firmware flashing will be completed when you are able to view the login screen on a

connected display.

© 2018 Appspace Inc. All Rights Reserved | Legal | Give Feedback

Otros manuales para Edge 300 Series

1

Tabla de contenidos

Otros manuales de Hardware de red de Cisco

Cisco

Cisco Aironet 1400 Series Manual de usuario

Cisco

Cisco Nexus 93180LC-EX Manual de usuario

Cisco

Cisco ATA 191 Manual de usuario

Cisco

Cisco Catalyst 8300 Series Manual

Cisco

Cisco NCS 1004 Manual de instalación

Cisco

Cisco Gigabit Switch Router Cisco 12012 Manual de usuario

Cisco

Cisco 3660 Series Manual de usuario

Cisco

Cisco o UCS X440p Instrucciones de instalación y mantenimiento

Cisco

Cisco Wide Area Virtualization Engine 274 Manual

Cisco

Cisco CPS-MSP-1RU-K9 Manual de usuario

Cisco

Cisco Catalyst 8510 Manual de usuario

Cisco

Cisco NSS4100 - Gigabit Storage System Manual de instrucciones

Cisco

Cisco SA-VAM - VPN Acceleration Module Manual del operador

Cisco

Cisco Linksys WES610N Manual de usuario

Cisco

Cisco IronPort C670 Manual de usuario

Cisco

Cisco WAVE-574-K9 - Wide Area Virtualization Engine... Manual

Cisco

Cisco AGS+ Manual de instrucciones

Cisco

Cisco Firepower 4100 Series Manual de usuario

Cisco

Cisco PC4000 Manual de usuario

Cisco

Cisco 3600 Series Instrucciones de funcionamiento y seguridad

Cisco

Cisco 7246 - uBR Router Manual de usuario

Cisco

Cisco ONS 15454 SDH Manual

Cisco

Cisco ASR 5500 Manual de usuario

Cisco

Cisco 6500 - Catalyst Series 10 Gigabit EN Interface Module... Manual de usuario

Manuales populares de Hardware de red de otras marcas

Matrix Switch Corporation

Matrix Switch Corporation MSC-HD161DEL Manual de usuario

B&B Electronics

B&B Electronics ZXT9-IO-222R2 Manual de usuario

Yudor

Yudor YDS-16 Manual de usuario

D-Link

D-Link ShareCenter DNS-320L Manual de usuario

Samsung

Samsung ES1642dc Instrucciones de uso

Honeywell Home

Honeywell Home LTEM-PV Instrucciones de montaje

evertz

evertz 7700 Series Manual de usuario

D-Link

D-Link ShareCenter DNS-343 Manual de usuario

Asante

Asante AsanteBridge 1012 Manual de usuario

FireBrick

FireBrick FB2700 Manual de usuario

Audiovox Electronics

Audiovox Electronics ARWH2T Manual de usuario

ADC

ADC DSX-1 Manual

NetComm

NetComm NF2 Manual de usuario

Alcatel-Lucent

Alcatel-Lucent 5620 Manual de usuario

Dell EMC

Dell EMC XC6420 Series Manual de usuario

Lanner

Lanner NCA-1020A Manual de usuario

Allied Telesis

Allied Telesis AT-TN121-A Manual de usuario

Arista

Arista CCA-ETM-Q12 Manual de usuario