Cisco 5400 Series Manual de instrucciones
Installing the Device
•Unpacking the Device, on page 1
•Locating the Product ID, Serial Number, Version ID and Common Language Equipment Identifies
(CLEI), on page 1
•Installing the Cisco 5400 ENCS, on page 2
•Powering On the Server, on page 5
•Initial Server Setup, on page 6
Unpacking the Device
The device, accessory kit, publications, and any optional units may be shipped in more than one container.
When you unpack the containers, check the packing list to ensure that you have received all the items on the
list.
Only unpack the product when you are ready to install it. This will help prevent accidental damage.
Locating the Product ID, Serial Number, Version ID and Common
Language Equipment Identifies (CLEI)
The serial number (SN), product ID (PID), version ID (VID), and Common Language Equipment Identifier
(CLEI) are printed on a label on the label tray located on the server chassis or motherboard.
Installing the Device
1
Figure 1: Label Tray
Serial Number2Product ID1
CLEI4PID/VID3
Installing the Cisco 5400 ENCS
If it is not already installed, the DIMMs, M.2 storage module and RAID card must be installed before
rack-mounting or wall-mounting the chassis. We recommend that you install the power supply when you have
the best access to the back panel of the device; this could be before or after you mount the device. You can
install the NIM and HDDs either before or after you mount the chassis.
Rack-Mounting the Chassis
The Cisco 5400 ENCS can be installed in 19-inch (48.26-cm) racks. Use the standard brackets shipped with
the router for mounting the chassis in a 19-inch EIA rack.
You can mount the device in the following ways:
• Front mounting—Brackets attached at the front of the chassis with the front panel facing forward
• Back mounting—Brackets attached at the back of the chassis with the back panel facing forward
• Center-front mounting—Brackets attached in the center front of the chassis with the front panel facing
forward
• Center-back mounting—Brackets attached in the center back of the chassis with the back panel facing
forward
Attaching Brackets to the Chassis
Attach one mounting bracket to each side of the device as shown in Figures 6 and 7. You will need four screws
to attach each bracket to the device; so, you will need eight screws in total to attach both the brackets to the
device. Use the screws provided along with the mounting kit to attach the screws to the device.
Installing the Device
2
Installing the Device
Installing the Cisco 5400 ENCS
Figure 2: Bracket Installation for Front Mounting
Figure 3: Bracket Installation for Back Mounting
Mounting the device in a Rack
After you attach the brackets to the device, install the chassis on the rack as shown in Figure 8. You will need
two screws to attach each bracket to the rack; so, you will need four screws in total to attach the device to the
rack. The screws for attaching the device to the rack are not provided with the kit.
Installing the Device
3
Installing the Device
Rack-Mounting the Chassis
Figure 4: Mounting the Chassis on the Rack - Front and Back
The screw slots in the brackets are spaced to line up with every second pair of screw holes in the rack. When
the correct screw holes are used, the small threaded holes in the brackets line up with unused screw holes in
the rack. If the small holes do not line up with the rack holes, you must raise or lower the brackets to the next
rack hole.
Tip
Wall-Mounting the Chassis
These are the steps to wall mount the chassis:
1. Attach the brackets to the device using the screws and plastic spacers provided with the mounting kit. As
shown in Figure 9, two screws and two plastic spaces should be used to attach each bracket to the chassis.
2. Fix the router to the wall using the brackets that you attached to the device. The screws for attaching the
device to the wall are not provided with the kit. Depending on the type of wall (wood, brick, stone etc),
use appropriate screws to fix the device to the wall.
Route the cables so that they do not put a strain on the connectors or mounting hardware.
Note
Installing the Device
4
Installing the Device
Wall-Mounting the Chassis
Figure 5: Wall Mounting the Server
Powering On the Server
When the power cord is connected to the system, both the management controller (CIMC) and the server is
automatically powered on. When the system is powered on, do not press the front-panel power button. If you
press the front-panel power button, it will power off the server, but the management controller (CIMC)
continues to be operational. You must press this button again to power on the server.
Note
1. Attach the power cord to the power supply unit in the server and then attach the other end of the power
chord to the grounded power outlet.
2. Wait for approximately three minutes.
3. Verify the power status of the system by looking at the system power status LED. The power status LED
blinks in amber color during initial boot up and in solid amber when the system reaches the standby power
mode.
Installing the Device
5
Installing the Device
Powering On the Server
Initial Server Setup
Local Connection Procedure
1. Ensure that the device is powered on.
2. Connect a keyboard and a monitor to the corresponding ports on the front panel of the device.
3. When you see the prompt, you can do the following:
• Press F2 to get into the setup (BIOS) to change some settings.
• Press F8 to configure the IP address of the CIMC.
4. After you have performed the required configuration, save the setup and continue to boot.
Remote Connection Procedure
1. Plug in your terminal server to the Serial CIMC port (Refer to Front panel of Chassis)
2. Telnet into the console and perform the necessary configuration using corresponding commands. You
can also configure the IP address for the Ethernet CIMC port.
Use CIMC to configure the box. For more details, see Initial Setup for UCS C-Series Servers.
Installing the Device
6
Installing the Device
Initial Server Setup
Tabla de contenidos
Otros manuales de Hardware de red de Cisco
Cisco
Cisco NCS 1004 Manual de usuario
Cisco
Cisco AIR-BR350-A-K9 - Aironet 350 Wireless Bridge Manual
Cisco
Cisco GS7000 Manual de usuario
Cisco
Cisco ASR 5000 Series Manual de usuario
Cisco
Cisco 2650XM Manual de usuario
Cisco
Cisco Firepower 2130 Guía de mantenimiento y servicio
Cisco
Cisco Octal-Port DMT ATU-C Line Card Manual técnico
Cisco
Cisco GS7000 Instrucciones de funcionamiento
Cisco
Cisco PRISMA II XD Manual de usuario
Cisco
Cisco NCS 2000 series Manual de usuario
Cisco
Cisco ISA 3000 Guía de inicio rápido
Cisco
Cisco CATALYST RPS 2300 Guía de inicio rápido
Cisco
Cisco IPS 7.1 Manual de usuario
Cisco
Cisco ASR 5000 Manual de instrucciones
Cisco
Cisco Aironet 1000 Series Manual
Cisco
Cisco 3660 Series Manual de usuario
Cisco
Cisco ESR-PRE2 Manual de usuario
Cisco
Cisco SCE 2000 4/8xFE Manual de usuario
Cisco
Cisco NTP-E157 Manual de lista de piezas
Cisco
Cisco linksys PLTK300 Manual de usuario
Manuales populares de Hardware de red de otras marcas
Matrix Switch Corporation
Matrix Switch Corporation MSC-HD161DEL Manual de usuario
B&B Electronics
B&B Electronics ZXT9-IO-222R2 Manual de usuario
Yudor
Yudor YDS-16 Manual de usuario
D-Link
D-Link ShareCenter DNS-320L Manual de usuario
Samsung
Samsung ES1642dc Instrucciones de uso
Honeywell Home
Honeywell Home LTEM-PV Instrucciones de montaje
