Cisco NCS 2000 series Manual de usuario

Installing the Cisco NCS 2000 Series Passive

Optical Modules

Last Modified: 2019-02-22

Installing the Cisco NCS 2000 Series Passive Optical Modules

Introduction

This document explains how to install and operate the Cisco NCS 2000 Series passive optical modules, the

fiber shuffle, and the MPO fan-out unit. The Cisco NCS 2000 Series encompasses platforms from Cisco NCS

2002 onwards.

The passive optical modules are used to build the optical network system. The fiber shuffle and MPO fan-out

unit mechanically holds 14 and 10 passive optical modules respectively, thus enabling interconnection of flex

spectrum ROADM nodes that contain 16-WXC or SMR-FS cards.

The passive optical modules, fiber shuffle, and MPO fan-out unit can be installed on:

• 19-inch (482.6 mm) or 23-inch (584.2 mm) EIA standard racks

• 19-inch (482.6 mm) IEC rack

• 600 mm x 600 mm or 600 mm x 300 mm ETSI rack

The following table lists the PIDs of the fiber shuffle and MPO fan-out unit:

Table 1: PIDs of the Fiber Shuffle and MPO Fan-out Unit

DescriptionModule

The MF-6RU unit is referred to as the fiber shuffle.

A combination of 14 single-slot NCS2K-MF-DEG-5

(NCS2K-MF-DEG-5-CV) and NCS2K-MF-UPG-4

(NCS2K-MF-UPG-4-CV) passive optical modules

can be installed in this unit. It is also possible to install

a combination of 14 single-slot

NCS2K-MF-2MPO-ADP, NCS2K-MF-4x4-COFS,

NCS2K-MF-MPO-8LC, and NCS2K-MF-6AD-CFS

passive optical modules.

NCS2K-MF-6RU= (MF-6RU)

Installing the Cisco NCS 2000 Series Passive Optical Modules

DescriptionModule

The MF10-6RU unit is referred to as the MPO fan-out

unit.

A combination of 10 double-slot

NCS2K-MF-10AD-CFS, NCS2K-MF-16AD-CFS,

NCS2K-MF-16AE-CFS, NCS2K-MF-MPO-16LC

(NCS2K-MF-M16LC-CV), NCS2K-MF-MPO-20LC,

and NCS2K-MF-8X10G-FO units can be installed in

this unit.

NCS2K-MF10-6RU= (MF10-6RU)

Blank unit for the MF-6RU unit.NCS2K-MF-1SL-CVR=

Blank unit for the MF-10-6RU unit.NCS2K-MF-2SL-CVR=

USB cable; two meters longNCS2K-USB3-CBL-2=

USB cable; three meters longNCS2K-USB3-CBL-3=

Plastic transparent cover for the MF-6RU and

MF-10-6RU unit.

NCS2K-MF-6RU-CVR=

All passive optical modules, (except the mesh patch panel module), are installed using the rack mounting

bracket that is one rack unit (RU) high and can be directly connected to the NCS 2015 ECU. The passive

optical modules can also be installed in the fiber shuffle or MPO fan-out unit.

The following table lists the passive optical modules:

DescriptionModule

16-channel colorless omni-directional add/dropNCS2K-MF-16AD-CFS=

4-channel colorless omni-directional add/dropNCS2K-MF-4X4-COFS=

MPO to 8-LC adapterNCS2K-MF-MPO-8LC=

5-degree mesh moduleNCS2K-MF-DEG-5=

4-degree upgrade moduleNCS2K-MF-UPG-4=

MPO-16 to 16-LC fan-out moduleNCS2K-MF-MPO-16LC=

Double MPO-16 to two MPO-8 adapter moduleNCS2K-MF-2MPO-ADP=

16-port add/drop module with express capabilityNCS2K-MF-16AE-CFS=

10-port add/drop moduleNCS2K-MF-10AD-CFS=

8-degree mesh patch panel with 5 add/drop portsNCS2K-PPMESH8-5AD=

5-degree mesh connection verification module with

MPO-8 loopback caps (NCS2K-MPO-LBK=)

NCS2K-MF-DEG-5-CV=

4-degree upgrade connection verification module with

MPO-8 loopback caps (NCS2K-MPO-LBK=)

NCS2K-MF-UPG-4-CV=

Installing the Cisco NCS 2000 Series Passive Optical Modules

Introduction

DescriptionModule

MPO-16 to 16-LC fan-out connection verification

module with LC loopback caps (NCS2K-LC-LBK=)

NCS2K-MF-M16LC-CV=

MPO-24 to 20-LC fan-out moduleNCS2K-MF-MPO-20LC

Splitter/coupler module with six ports used as

colorless or gridless add/drop units in NCS2K

ROADM configurations.

NCS2K-MF-6AD-CFS=

MPO to LC fan-out module used as client

interconnection for the NCS2K and NCS4K line cards

using QSFP+ ports.

NCS2K-MF-8X10G-FO=

• All modules can be used to accommodate the ROADM nodes built with the SMR-FS and AD-FS cards.

• A set of photodiodes are included on selected ports of each module for optical power monitoring.

•USB communication channel can be used to retrieve the optical power levels monitored by the photodiodes

and the inventory and insertion loss (IL) data of the optical paths stored in the modules. The USB channel

can also be used to activate electrical actuators or LEDs present on the front panel of the module.

• The xx SMR9 FS, SMR20 FS, or SMR20 FS CV and the 12-AD-FS or 16-AD-FS cards can be

interconnected by the NCS2K-MF-UPG-4=, NCS2K-MF-UPG-4-CV=, NCS2K-MF-DEG-5=,

NCS2K-MF-DEG-5-CV=, NCS2K-MF-MPO-16LC=, NCS2K-MF-M16LC-CV=,

NCS2K-MF-2MPO-ADP=, or the NCS2K-PPMESH8-5AD= module.

• The NCS2K-MF-16AE-CFS= and the NCS2K-MF-10AD-CFS= modules are only used as a passive

add/drop modules in the Not-DWDM networks.

The following table lists the MPO cables that can be used with the passive modules from Release 10.6.1:

DescriptionMPO Cables

Fan-out cable with one MPO-24 connector on one

side and 16 LC connectors on the other side.

The cable is two meters long and can be used in

ROADM configurations with the

NCS2K-MF-6AD-CFS module. This cable can also

be used as a fan-out cable to connect the LC interface

directly to the SMR20 FS MPO ports.

ONS-MPO-16LC-2

Multi-fiber patch cord with MPO-12 connectors. The

12 fibers have straight connections. There are four

variants: two, four, six, and eight meters.

• ONS-12MPO-MPO-2=

• ONS-12MPO-MPO-4=

• ONS-12MPO-MPO-6=

• ONS-12MPO-MPO-8=

The cables can interconnect the QSFP+ client ports

of NCS2K-400G-2C2 and NCS4K-4H-OPW-QC2

with the NCS2K-MF-8X10G-FO passive module.

ONS-12MPO-MPO-x

Installing the Cisco NCS 2000 Series Passive Optical Modules

Introduction

DescriptionMPO Cables

Multi-fiber patch cord with MPO-12 connectors. The

12 fibers have crossed fiber interconnections. There

are four variants: two, four, six, and eight meters.

• ONS-12MPO-XMPO-2=

• ONS-12MPO-XMPO-4=

• ONS-12MPO-XMPO-6=

• ONS-12MPO-XMPO-8=

The cable is used to interconnect the

NCS2K-MF-DEG-5-CV and the

NCS2K-MF-UPG-4-CV passive modules with the

NCS2K-MF-MPO-8LC adapter.

ONS-12MPO-XMPO-x

Multi-fiber patch cord with MPO-24 connectors that

has only 16 fibers connected. Fibers 1, 2, 11, 12, 13,

14, 23, and 24 are not connected. There are four

variants: two, four, six, and eight meters.

• ONS-16MPO-MPO-2=

• ONS-16MPO-MPO-4=

• ONS-16MPO-MPO-6=

• ONS-16MPO-MPO-8=

The cable is used for interconnections inside the

ROADM with MPO-24 standard. The patch cord can

be used for interconnections between SMR20 FS and

NCS2K-MF-M16LC-CV, or NCS2K-MF-2MPO-ADP

or NCS2K-PPMESH8-5AD. The patch cord can also

be used for interconnections between

NCS2K-16-AD-CCOFS and

NCS2K-MF-M16LC-CV.

ONS-16MPO-MPO-x

Safety Information

Before you install, operate, or service the passive optical modules, you must read the Regulatory Compliance

and Safety Information for Cisco NCS 2000 Series document for important safety information and warning

translations.

The passive optical modules are compliant with the GR 1089, UL60950 /CSA 22.2 No. 60950-00, and IEC

60950 standards.

Laser Radiation Emission Restrictions

The Class 1M Laser safety and warning label affixed to the passive optical modules indicate that the product

should never be used or installed in an optical network with emissions higher than Class 1M.

Class 1M laser radiation when open. Do not view directly with optical instruments. Statement 281

Warning

Installing the Cisco NCS 2000 Series Passive Optical Modules

Safety Information

Laser Safety During Operation

Invisible laser radiation may be emitted from disconnected fibers or connectors. Do not stare into beams or

view directly with optical instruments. Statement 1051

Warning

Electrical Safety

The passive optical modules are optically and electrically passive and require no electrical connections. No

electrostatic discharge (ESD) or other electrical safety considerations apply.

Fiber Shuffle

The MF-6RU unit is six RU high and can be used to interface 14 single slot passive optical modules with the

NCS 2015 ECU. It contains a USB 3.0 hub that consolidates all USB 2.0 connections between the passive

optical modules units and the NCS 2015 ECU using a single USB cable. It allows connections between line

cards and optical passive modules units using simple cabling. The slots are covered by blank units. The

MF-6RU unit is shipped with USB connectors connected to the corresponding blank units. A plastic transparent

door can be installed in front of the unit for fiber and cable management. Mounting brackets are shipped with

the unit.

Figure 1: NCS2K-MF-6RU Unit

Cable guide2Blank unit1

USB connector3

Installing the Cisco NCS 2000 Series Passive Optical Modules

Laser Safety During Operation

MPO Fan-out Unit

The MF10-6RU unit is six RU high and can be used to interface 10 double slot passive optical modules with

the NCS 2015 ECU. It contains a USB 3.0 hub that consolidates all USB 2.0 connections between the passive

optical modules units and the NCS 2015 ECU using a single USB cable. It allows connections between line

cards and optical passive modules units using simple cabling. It also has an additional USB 3.0 port on its

faceplate that allows it to be connected to only one MF10-6RU unit.

The slots are covered by blank units and USB connectors are connected to the corresponding blank units. A

plastic transparent door can be installed in front of the unit for fiber and cable management. Mounting brackets

are shipped with the unit.

Figure 2: NCS2K-MF10-6RU Unit

Cable guide2Blank unit1

USB connector3

This procedure describes the steps to install the MF-6RU or MF10-6RU unit on the ANSI or ETSI equipment

rack.

Procedure

Step 1 For a 23-inch ANSI or 21-inch ETSI rack installation, mount the four brackets on the MF-6RU unit or

MF10-6RU unit and:

a) Place the mounting bracket flush against the MF-6RU or MF-0-6RU unit.

b) Align the mounting bracket screw holes against the MF-6RU or MF10-6RU unit screw holes.

c) Insert the M6 screws and tighten them.

d) Repeat steps 1a through 1c to mount the remaining three brackets on the unit.

Installing the Cisco NCS 2000 Series Passive Optical Modules

MPO Fan-out Unit

Figure 3: Mounting Brackets on the MF-6RU Unit for a 23-inch ANSI Rack Installation

Washer223-inch ANSI rack

mounting bracket

Screw3

Installing the Cisco NCS 2000 Series Passive Optical Modules

MPO Fan-out Unit

Figure 4: Mounting Brackets on the MF-6RU Unit for a 21-inch ETSI Rack Installation

Washer2Z shaped 21-inch ETSI

rack mounting bracket

Screw3

Installing the Cisco NCS 2000 Series Passive Optical Modules

MPO Fan-out Unit

Figure 5: Mounting Brackets on the MF10-6RU Unit for a 23-inch ANSI Rack Installation

Washer223-inch ANSI rack

mounting bracket

Screw3

Installing the Cisco NCS 2000 Series Passive Optical Modules

MPO Fan-out Unit

Figure 6: Mounting Brackets on the MF10-6RU Unit for a 21-inch ETSI Rack Installation

Washer2Z shaped 21-inch ETSI

rack mounting bracket

Screw3

Step 2 Install the MF-6RU or MF10-6RU unit on the appropriate rack equipment:

a) Lift the MF-6RU or MF10-6RU unit to the desired position in the rack.

b) Align the screw holes on the mounting brackets with the mounting holes in the rack.

For a 19-inch ANSI rack installation, external mounting brackets are not installed on the MF-6RU

or MF10-6RU unit. The unit is mounted directly on the equipment rack using screws and washers.

Note

c) Insert the screws and tighten them.

Installing the Cisco NCS 2000 Series Passive Optical Modules

MPO Fan-out Unit

Otros manuales para NCS 2000 series

Tabla de contenidos

Otros manuales de Hardware de red de Cisco

Cisco

Cisco FirePOWER 8000 Series Manual de usuario

Cisco

Cisco ISA500 Series Manual de usuario

Cisco

Cisco SCE 1000 and Manual del operador

Cisco

Cisco NM-1A-T3 - 1port Ds3 Atm Network Module Manual de usuario

Cisco

Cisco Linksys Business Series Network Storage System... Manual de usuario

Cisco

Cisco FPR1150-ASA-K9 Manual

Cisco

Cisco 1230AG - Aironet - Wireless Access Point Manual de usuario

Cisco

Cisco AIR-BR350-A-K9 - Aironet 350 Wireless Bridge Manual

Cisco

Cisco Edge 300 Series Guía de inicio rápido

Cisco

Cisco ONS 15216-MD-40-ODD Manual de usuario

Cisco

Cisco 3600 Series Instrucciones de funcionamiento y seguridad

Cisco

Cisco ONS 15310-MA SDH Manual

Cisco

Cisco Secure Network Server 3700 Series Manual

Cisco

Cisco IAD2430 Series Manual

Cisco

Cisco 7246 - uBR Router Manual de usuario

Cisco

Cisco ONS 15540 ESP Manual

Cisco

Cisco N540X-6Z18G-SYS-A Manual de usuario

Cisco

Cisco ASR 9000 Series Manual de usuario

Cisco

Cisco Catalyst 8300 Series Manual

Cisco

Cisco GS7000 Instrucciones de funcionamiento

Cisco

Cisco WBPN Manual de usuario

Cisco

Cisco o UCS X440p Instrucciones de instalación y mantenimiento

Cisco

Cisco RSP4+ Bootflash Memory Upgrade to 16MB... Manual del operador

Cisco

Cisco CATALYST 6000 Manual de instalación y operación

Manuales populares de Hardware de red de otras marcas

Matrix Switch Corporation

Matrix Switch Corporation MSC-HD161DEL Manual de usuario

B&B Electronics

B&B Electronics ZXT9-IO-222R2 Manual de usuario

Yudor

Yudor YDS-16 Manual de usuario

D-Link

D-Link ShareCenter DNS-320L Manual de usuario

Samsung

Samsung ES1642dc Instrucciones de uso

Honeywell Home

Honeywell Home LTEM-PV Instrucciones de montaje

evertz

evertz 7700 Series Manual de usuario

D-Link

D-Link ShareCenter DNS-343 Manual de usuario

Asante

Asante AsanteBridge 1012 Manual de usuario

FireBrick

FireBrick FB2700 Manual de usuario

Audiovox Electronics

Audiovox Electronics ARWH2T Manual de usuario

ADC

ADC DSX-1 Manual

NetComm

NetComm NF2 Manual de usuario

Alcatel-Lucent

Alcatel-Lucent 5620 Manual de usuario

Dell EMC

Dell EMC XC6420 Series Manual de usuario

Lanner

Lanner NCA-1020A Manual de usuario

Allied Telesis

Allied Telesis AT-TN121-A Manual de usuario

Arista

Arista CCA-ETM-Q12 Manual de usuario