Cisco Firepower 4100 Series Manual de instalación y operación

Maintenance and Upgrade

•Install the Network Module, on page 1

•Remove and Replace the Fan Module, on page 4

•Remove and Replace the SSD, on page 5

•Remove and Replace the Power Supply Module, on page 8

•Connect the DC Power Supply Module, on page 10

•Secure the Power Cord on the AC Power Supply Module, on page 16

Install the Network Module

Take note of the following warnings:

Statement 60—UL- and CSA-Certified Equipment Warning

This card is intended to be installed in UL- and CSA-certified equipment in the field by the user in the

manufacturer's defined operator access area. Check the equipment manufacturer to verify/confirm that your

equipment is suitable for user-installed application cards.

Warning

Statement 1029—Blank Faceplates and Cover Panels

Blank faceplates and cover panels serve three important functions: they prevent exposure to hazardous voltages

and currents inside the chassis; they contain electromagnetic interference (EMI) that might disrupt other

equipment; and they direct the flow of cooling air through the chassis. Do not operate the system unless all

cards, faceplates, front covers, and rear covers are in place.

Warning

Statement 1030—Equipment Installation

Only trained and qualified personnel should be allowed to install, replace, or service this equipment.

Warning

Maintenance and Upgrade

Statement 1040—Product Disposal

Ultimate disposal of this product should be handled according to all national laws and regulations.

Warning

Statement 1073—No User-Serviceable Parts

No serviceable parts inside. To avoid risk of electric shock, do not open.

Warning

Statement 1077—Do Not Operate Unit Without Covers

The covers are an integral part of the safety design of the product. Do not operate the unit without the covers

installed.

Warning

Hot Swapping

Starting with FXOS 2.3.1, the Firepower 10-Gb and 40-Gb network modules (without hardware bypass

support) support hot swapping, but you must hot swap with an identical network module, that is, a network

module with the same PID. See Product ID Numbers for the network module PIDs. You must bring the

network module offline using the appropriate CLI commands before removing the network module from

the chassis so that all network module configuration is saved. See the “Taking a Network Module Offline

or Online” topic in the Security Module/Engine Management chapter in the Cisco FXOS Firepower

Chassis Manager Configuration Guide.

We do not recommend that you remove the network module without bringing it properly offline using

the appropriate CLI commands.

Caution

You must have ROMMON 1.0.10 or later on the Supervisor to support hot swapping. For the ROMMON

upgrade procedure, see the "Firmware Upgrade" topic in the Image Management chapter in the Cisco

FXOS Firepower Chassis Manager Configuration Guide for your software version.

Note

To remove and replace the network modules that do not currently support hot swapping, power off the chassis,

replace the network module, and then power the chassis back on.

Acknowledgment is necessary if you decommission and physically remove a network module and do not

replace it, or if you replace it with another PID. See the "Acknowledging a Security Module/Engine” topic

in the Security Module/Engine Management chapter in the Cisco FXOS Firepower Chassis Manager

Configuration Guide.

Step 1 To install a new network module for the first time into an empty slot, do the following:

a) Power down the chassis by moving the power switch to the OFF position.

See Features for more information about the power switch.

b) Follow Steps 4 through 7 to install the new network module.

Maintenance and Upgrade

Install the Network Module

c) Power on the chassis by moving the power switch to the ON position.

The state for the new network module is OIR Failed.

d) To change the status of the network module to Online, reboot the chassis. See the "Rebooting the Firepower 4100/9300

Chassis" topic in the System Administration chapter in the FXOS Configuration Guide for your software version.

Step 2 To remove and replace an existing network module, do one of the following:

a) Save your configuration.

b) Power down the chassis by moving the power switch to the OFF position (if removing a network module that does

not support hot swapping).

See Features for more information about the power switch.

c) Bring the network module offline using the appropriate CLI command (if removing a network module that supports

hot swapping). All network module configuration is saved. See the “Taking a Network Module Offline or Online”

topic in the Security Module/Engine Management chapter in the FXOS Configuration Guide for your software version.

d) Continue with Step 3.

Step 3 To remove a network module from the chassis, loosen the captive screw on the lower left side of the network module

and pull out the handle that is connected to the screw. This mechanically ejects the network module from the slot.

Figure 1: Remove the Network Module

If the slot is to remain empty, install a blank faceplate to ensure proper airflow and to keep dust out of the chassis;

otherwise, install another network module.

Step 4 To replace a network module, hold the network module in front of the network module slot on the right of the chassis

and pull the network module handle out.

Step 5 Slide the network module into the slot and push it firmly into place until the handle is flush with the front of the network

module.

Step 6 Tighten the captive screw on the lower left side of the network module.

Step 7 Do one of the following:

a) Power up the chassis so that the new network module is recognized (if the new network module does not support hot

swapping).

b) Bring the new network module online using the appropriate CLI command (if the new network module supports hot

swapping). The saved network module configuration is automatically reapplied when the network module is back

online.

Maintenance and Upgrade

Install the Network Module

If you install a network module that is a different PID than the original network module, the saved

configuration is deleted and the default configuration is applied. You must enter the acknowledge command

to confirm the network module PID change.

Note

What to do next

Follow the procedures in the FXOS Configuration Guide to connect to the network module and make sure

that it has been discovered correctly by the Firepower 4100.

Remove and Replace the Fan Module

Take note of the following warnings:

Statement 60—UL- and CSA-Certified Equipment Warning

This card is intended to be installed in UL- and CSA-certified equipment in the field by the user in the

manufacturer's defined operator access area. Check the equipment manufacturer to verify/confirm that your

equipment is suitable for user-installed application cards.

Warning

Statement 1030—Equipment Installation

Only trained and qualified personnel should be allowed to install, replace, or service this equipment.

Warning

Statement 1040—Product Disposal

Ultimate disposal of this product should be handled according to all national laws and regulations.

Warning

Statement 1073—No User-Serviceable Parts

No serviceable parts inside. To avoid risk of electric shock, do not open.

Warning

Statement 1077—Do Not Operate Unit Without Covers

The covers are an integral part of the safety design of the product. Do not operate the unit without the covers

installed.

Warning

You can remove and replace fan modules while the system is running. The air flow moves from front to back.

If you remove a fan or a fan fails, the other fans operate at full speed, which can be noisy.

Maintenance and Upgrade

Remove and Replace the Fan Module

The system supports operation with a single fan failure (N+1 fan redundancy), but do not run the system for

an extended amount of time without all fan modules installed. Keep removal and replacement time at three

minutes. Remove and replace one fan module at a time.

Note

Step 1 To remove a fan module, face the rear of the chassis, and grasp the handle of the fan module.

Step 2 Squeeze the handle to disengage the latches on the left and right of the fan module.

Step 3 Pull the fan module out of the chassis.

Figure 2: Remove the Fan Module

Step 4 To replace a fan module, hold the fan module in front of the fan slot.

Step 5 Push the fan module into the chassis until it is properly seated and the latches snap into place.

If the system is powered on, listen for the fans. You should immediately hear the fans operating. If you do not hear the

fans, make sure the fan module is inserted completely into the chassis and the faceplate is flush with the outside surface

of the chassis.

Step 6 Verify that the fan is operational by checking the fan module LED. See Front Panel LEDs for a description of the fan

LEDs.

Remove and Replace the SSD

Take note of the following warnings:

Maintenance and Upgrade

Remove and Replace the SSD

Statement 60—UL- and CSA-Certified Equipment Warning

This card is intended to be installed in UL- and CSA-certified equipment in the field by the user in the

manufacturer's defined operator access area. Check the equipment manufacturer to verify/confirm that your

equipment is suitable for user-installed application cards.

Warning

Statement 1029—Blank Faceplates and Cover Panels

Blank faceplates and cover panels serve three important functions: they prevent exposure to hazardous voltages

and currents inside the chassis; they contain electromagnetic interference (EMI) that might disrupt other

equipment; and they direct the flow of cooling air through the chassis. Do not operate the system unless all

cards, faceplates, front covers, and rear covers are in place.

Warning

Statement 1030—Equipment Installation

Only trained and qualified personnel should be allowed to install, replace, or service this equipment.

Warning

Statement 1040—Product Disposal

Ultimate disposal of this product should be handled according to all national laws and regulations.

Warning

Statement 1073—No User-Serviceable Parts

No serviceable parts inside. To avoid risk of electric shock, do not open.

Warning

Statement 1077—Do Not Operate Unit Without Covers

The covers are an integral part of the safety design of the product. Do not operate the unit without the covers

installed.

Warning

Although the hardware supports removing and replacing SSDs while the system is running, the software does

not currently support hot swapping. You must power down the chassis to remove and replace SSDs.

If your Firepower 4100 is running Firepower Threat Defense software, we recommend that you upgrade to

the latest version to take advantage of software updates that enhance SSD management performance and

longevity.

Note

You storage SSD must be installed in slot 1 and must be present. Only an optional MSP can be installed in

the second SSD slot (SSD slot 2). The MSP stores threat detection results for use in future analysis. It supports

Maintenance and Upgrade

Remove and Replace the SSD

the Advanced Malware Protection software feature. The MSP is supported beginning in FXOS 2.0.1. It is

used as both storage and as the Malware application repository. RAID is not supported.

Do not switch the two SSDs. The storage SSD must be installed in slot 1. The optional MSP SSD must be

installed in slot 2. If you remove it and install it in slot 1, all stored file capture data is lost.

Caution

Step 1 Save your configuration.

Step 2 Power down the chassis by moving the power switch to the OFF position. See Features for more information about the

power switch.

Step 3 To remove an SSD, face the front of the chassis, loosen the two captive screws on the SSD, and gently pull it out of slot

1 of the chassis.

Figure 3: Remove the SSD

Step 4 To replace the SSD, make sure the power switch is still in the OFF position, and then hold the SSD in front of slot 1 and

push it in gently until it is seated.

Step 5 To install the MSP SSD, make sure the power switch is still in the OFF position and then remove the blank faceplate in

slot 2 by loosening the captive screws on either side of the faceplate.

Step 6 Hold the MSP SSD in front of slot 2 and push it in gently until it is seated.

Do not switch the two SSDs. Only the optional MSP SSD can be installed in slot 2. If you remove it and install

it in slot 1, all stored file capture data is lost.

Caution

Step 7 Tighten the captive screws on either side of the SSD.

Step 8 Verify that the SSD is operational by checking the SSD LED. See Front Panel LEDs for a description of the fan LEDs.

Maintenance and Upgrade

Remove and Replace the SSD

Remove and Replace the Power Supply Module

Take note of the following warnings:

Statement 1002—DC Power Supply

When stranded wiring is required, use approved wiring terminations, such as closed-loop or spade-type with

upturned lugs. These terminations should be the appropriate size for the wires and should clamp both the

insulation and conductor.

Warning

Statement 1003—DC Power Disconnection

Before performing any of the following procedures, ensure that power is removed from the DC circuit.

Warning

Statement 1005—Circuit Breaker

This product relies on the building's installation for short-circuit (overcurrent) protection. Ensure that the

protective device is rated not great than: AC power 120 V AC, 20 A (US), 240 V AC, 16 A (EU), DC power

60 V, 35 A.

Warning

Statement 1022—Disconnect Device

To reduce risk of electric shock and fire, a readily accessible two-poled disconnect device must be incorporated

in the fixed wiring.

Warning

Statement 1025—Use Copper Conductors Only

To reduce risk of fire, use copper conductors only.

Warning

Statement 1028—More Than One Power Supply

This unit might have more than one power supply connection. To reduce risk of electric shock, all connections

must be removed to de-energize the unit.

Warning

Maintenance and Upgrade

Remove and Replace the Power Supply Module

Statement 1030—Equipment Installation

Only trained and qualified personnel should be allowed to install, replace, or service this equipment.

Warning

Statement 1040—Product Disposal

Ultimate disposal of this product should be handled according to all national laws and regulations.

Warning

Statement 1045—Short-Circuit Protection

This product requires short-circuit (overcurrent) protection to be provided as part of the building installation.

Install only in accordance with national and local wiring regulations.

Warning

Statement 1046—Installing or Replacing the Unit

To reduce risk of electric shock, when installing or replacing the unit, the ground connection must always be

made first and disconnected last.

Warning

Statement 1073—No User-Serviceable Parts

No serviceable parts inside. To avoid risk of electric shock, do not open.

Warning

Statement 1077—Do Not Operate Unit Without Covers

The covers are an integral part of the safety design of the product. Do not operate the unit without the covers

installed.

Warning

You can remove and replace power supply modules while the system is running.

Step 1 To remove a power supply module, face the back of the chassis and grasp the handle.

Step 2 Press the latch found on the lower right of the power supply to disengage the power supply.

Step 3 Place your other hand under the power supply module to support it while you slide it out of the chassis.

Maintenance and Upgrade

Remove and Replace the Power Supply Module

Figure 4: Remove the Power Supply Module

If the slot is to remain empty, install a blank faceplate to ensure proper airflow and to keep dust out of the chassis;

otherwise, install another power supply module.

Step 4 To replace a power supply module, hold the power supply module with both hands and slide it into the power supply

module bay.

Step 5 Push in the power supply module gently until you hear the latch engage and it is seated. Verify the power supply module

is operating correctly by checking the power supply module LED. See Power Supply Modules for a description of the

power supply module LEDs.

Connect the DC Power Supply Module

Take note of the following warnings:

Statement 1002—DC Power Supply

When stranded wiring is required, use approved wiring terminations, such as closed-loop or spade-type with

upturned lugs. These terminations should be the appropriate size for the wires and should clamp both the

insulation and conductor.

Warning

Maintenance and Upgrade

Connect the DC Power Supply Module

Otros manuales para Firepower 4100 Series

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Cortafuegos de Cisco

Cisco

Cisco RV110W Manual de usuario

Cisco

Cisco Firepower 1010 Manual

Cisco

Cisco PIX-525-UR-BUN - PIX 525 Unrestricted Bundle Manual de usuario

Cisco

Cisco Firepower 1100 Series Manual

Cisco

Cisco M690 Manual de usuario

Cisco

Cisco Spam Manual de usuario

Cisco

Cisco M170 Manual de usuario

Cisco

Cisco IronPort M1070 Manual de usuario

Cisco

Cisco S195 Manual

Cisco

Cisco C690 Manual de usuario

Cisco

Cisco Cisco ASA 5510 Manual de usuario

Cisco

Cisco ASA 5550 Series Manual de usuario

Cisco

Cisco ASA 5508-X Manual de usuario

Cisco

Cisco Small Business Pro SA 520W Manual de instrucciones

Cisco

Cisco ASA 5506-X Instrucciones de instalación

Cisco

Cisco 881W - Integrated Services Router Wireless Manual de instrucciones

Cisco

Cisco Firepower 1100 Manual de usuario

Cisco

Cisco 515E - PIX Restricted Bundle Manual de usuario

Cisco

Cisco M190 Manual de usuario

Cisco

Cisco Firepower 3500 Documento técnico

Cisco

Cisco Firepower 2100 Manual de usuario

Cisco

Cisco PIX 506 - Firewall Manual de usuario

Cisco

Cisco 5505 - ASA Firewall Edition Bundle Manual de usuario

Cisco

Cisco LightStream 1010 Manual de usuario

Manuales populares de Cortafuegos de otras marcas

Fortinet

Fortinet FortiGate Voice Series Manual de usuario

ADTRAN

ADTRAN NetVanta 2300 Manual de usuario

SecureLogix

SecureLogix ETM System Manual de usuario

NETGEAR

NETGEAR ProSafe FVX538 Manual de usuario

Lanner

Lanner FW-8877 Manual de usuario

Huawei

Huawei USG6000 Series Manual de instalación y operación

H3C

H3C SecPath F5000-AI-15 Manual de usuario

Nexcom

Nexcom DNA 1150 Manual de usuario

Fortinet

Fortinet FortiGate-60 series Manual de usuario

Draytek

Draytek Vigor2860 Series Manual de usuario

Lanner electronics

Lanner electronics FW-7650 Series Manual de usuario

Swisscom

Swisscom Internet Backup Manual de usuario

SonicWALL

SonicWALL NSa 5700 Manual de usuario

DPtech

DPtech FW1000 SERIES Manual de usuario

FEITIAN

FEITIAN MultiPass FIDO Manual de usuario

EBLOCKER

EBLOCKER PRO Manual de usuario

GTA

GTA GB-200 Manual de usuario

Trend Micro

Trend Micro Deep Edge Manual de usuario