Cisco M190 Manual de usuario

Cisco Systems, Inc.

www.cisco.com

Cisco M190 Content Security

Management Appliance 

Quick Start Guide

• Welcome

• Before You Begin

• Plan the Installation

• Document Required Settings

• Install the Appliance in a Rack

• Temporarily Change Your IP Address for Remote Access

• Connect to the Appliance

• Plug In and Power Up the Appliance

• Log In to the Appliance

• Run the System Setup Wizard

• Check for Available Upgrades

• Configure Network Settings

• Additional Configurations

• Where to Go From Here

• Cisco Notification Service

Welcome

Thank you for choosing the Cisco M190 Content Security Management

Appliance (Cisco M190).

The Cisco M190 Content Security Management Appliance centralizes reporting

and tracking, management of quarantined email messages, and web security

appliance configuration settings. It also allows automated data backups.

This guide describes the basic steps for setting up your appliance.

Before You Begin

Before you begin the installation, make sure that you have the items you need.

The following items are included with the Cisco M190 Content Security

Management Appliance:

• Rail kit

• Power cords

• Console cable

• A card listing the location of online documentation for your appliance.

You will need to provide the following items yourself:

• Rack cabinet enclosure (if rack-mounting the appliance)

• Phillips-head screwdriver for assembling rails

• 10/100 Gigabit Base-T TCP/IP LAN

• Ethernet cable for connecting the appliance to your network

• Desktop or laptop computer

• Web browser (or SSH and terminal software)

• Network and administrator information for the “Plan the Installation”

section on page 3

Plan the Installation

The Cisco M190 appliance is designed to sit within your inner DMZ and

communicate with Cisco C-Series and S-Series appliances in your outer DMZ.

Plan for your network configuration to look something like this:

Document Required Settings

Before you begin, write down the following information about your system,

network, and administrator settings.You will need this information when

running the System Setup Wizard.

System Settings

The default password will not work after you

enter this new password.

Your password must contain at least 8

characters, one number, one upper-case letter,

one lower-case letter, and one special

character.)

Network Settings

Email system alerts to:

Time Zone Information:

NTP Server:

Admin Password:

AutoSupport: Enable/Disable

Fully Qualified Appliance Hostname

IP Address (Data Port 1)

Network Mask:

Default Gateway (Router) IP Address:

DNS (Use the Internet’s root DNS servers or

specify your own):

Data Port 2

IP Address:

Network Mask:

Install the Appliance in a Rack

Install the Cisco M190 Content Security Management Appliance following the

instructions in the Cisco x90 Series Content Security Appliances Installation and

Maintenance Guide.

Appliance Placement

• Ambient Temperature—To prevent the appliance from overheating, do not

operate it in an area that exceeds an ambient temperature of 104°F (40°C).

• Air Flow—Be sure that there is adequate air flow around the appliance.

• Mechanical Loading—Be sure that the appliance is level and stable to avoid

any hazardous conditions.

Temporarily Change Your IP Address for Remote

Access

To remotely configure the Cisco M190 using the network connection, you must

temporarily change the IP address of your computer. Alternatively, you can use

the serial console to configure the Cisco M190, without changing the IP address.

If you use the serial console, proceed to section below.

Note Make a note of your current IP configuration settings as you will need

to revert to these settings after you finish the configuration.

For Windows

The exact steps depend on your operating system version.

Step 1 Go to the Start menu and choose Control Panel.

Step 2 Click Network and Internet, then Network and Sharing Center.

Step 3 Click the Change adapter settings link.

Step 4 Right-click Local Area Connection and choose Properties.

Step 5 Click Internet Protocol Version 4, then choose Properties.

Step 6 Note your current settings.

Step 7 Select Use the Following IP Address.

Step 8 Enter the following changes:

–

IP Address: 192.168.42.43

–

Subnet Mask: 255.255.255.0

–

Default Gateway: 192.168.42.1

Step 9 Click OK and OK again to exit the dialog box.

For Mac

The exact steps depend on your operating system version.

Step 1 Launch the Apple menu and choose System Preferences.

Step 2 Click Network.

Step 3 Click the lock icon to allow changes.

Step 4 Select the network configuration with the green icon. This is your active

connection. Then click Advanced.

Step 5 Click the TCP/IP tab and from Ethernet settings, choose Manually from

the drop-down list.

Step 6 Enter the following changes:

• IP Address: 192.168.42.43

• Subnet Mask: 255.255.255.0

• Router: 192.168.42.1

Step 7 Click OK.

Connect to the Appliance

The Cisco M190 appliance has two gigabit network ports: 

Data 1 and Data 2.

For the purposes of setup, connect to Data 1 as your management interface and

configure incoming web traffic or email on the Data 2 interface. These settings

can be changed after the initial installation.

Item Port Description

1Remote

Power Cycle

The port that is used for Remote

Power Cycle (RPC).

2Console The console port that directly

connects a computer to the

appliance.

3Data 1 A Gigabit Ethernet customer data

interface. This port is used as a

management interface.

4Data 2 A Gigabit Ethernet customer data

interface.

Plug In and Power Up the Appliance

Plug in the appliance, then power up the appliance by pressing the On/Off

switch on the front panel of the Cisco M190. You must wait 10 minutes for the

system to initialize each time you power up the system.

After the machine powers up, solid green lights on the front of the appliance

indicate that the appliance is operational. The network activity light will be

green but may not be solid.

Caution If turned on quickly after connecting power to the appliance, the

appliance powers up, the fans spin and the LEDs turn on. Within

30-60 seconds, the fans stop and all LEDs turn off. The appliance

powers on 31 seconds later. This behavior is by design to allow the

system firmware and controller to synchronize. 



Wait at least 10 minutes for the system to complete the power up

sequence and the LEDs to turn green. If you turn the power off

before the initialization is complete, the appliance will NOT reach

an operational state and must be returned to Cisco.

You can log into the Cisco M190 using the web-based interface or the command

line interface.

Web-Based Interface

Step 1 For web browser access via the Ethernet port (see the “Connect to the

Appliance” section on page 7), log in to the Cisco M190 appliance by

entering the following URL in a web browser:

http://192.168.42.42

Step 2 Enter the following login information:

• Username: admin

• Password: ironport

Note The hostname parameter is assigned during system setup. Before you

can connect to the web interface using a hostname (http://hostname),

you must add the appliance hostname and IP address to your DNS

server.

Step 3 Click Login.

Command-Line Interface

Step 1 Access the command-line interface locally or remotely:

• To access the CLI locally, set up a terminal to connect to the serial

port using 9600 bits, 8 bits, no parity, 1 stop bit (9600, 8, N, 1) and

flow control set to Hardware. To physically connect the terminal,

see the “Connect to the Appliance” section on page 7).

• To access the CLI remotely, initiate an SSH session to the IP address

192.168.42.42.

Step 2 Log in as admin with the password ironport.

Step 3 At the prompt, run the systemsetup command.

Run the System Setup Wizard

Run the System Setup Wizard to configure basic settings and enable a set of

system defaults. The System Setup Wizard starts automatically when you access

the appliance via the web-based interface (or when you run the systemsetup

command from the command-line interface.)

Step 1 Accept the end user license agreement.

Step 2 Enter system and network information from the “Plan the Installation”

section on page 3.

If you need additional information about the settings, choose Help and

Support > Online Help.

Step 3 Review the configuration summary page.

Step 4 Click Install this Configuration.

The appliance may not appear to have accepted your configuration or

be performing the installation. This is because you have changed the IP

address, but the installation is underway.

Step 5 If you temporarily changed the IP address of your computer as

described above, change the IP address settings back to the original

values.

Step 6 Ensure that your laptop and the appliance are connected to the

network.

Step 7 Log in to the appliance again, at the hostname or IP address that you

noted in the “Plan the Installation” section on page 3. Use the username

admin and the new password that you entered in the wizard.

The Cisco M190 Content Security Management Appliance uses a

self-signed certificate that may trigger a warning from your web

browser. You can simply accept the certificate and ignore this warning.

Step 8 Be sure to keep your new administrator password in a safe place.

Check for Available Upgrades

After logging in to the appliance, look at the top of the web browser window for

an upgrade notification (or for a notice in the command-line interface.) If an

upgrade is available, evaluate whether you should install it.

For example, make sure that the new version is compatible with the AsyncOS

versions of managed email and web appliances in your environment.

Details about each release are available in the release notes for that Async OS

version.

Tabla de contenidos

Otros manuales de Cortafuegos de Cisco

Cisco

Cisco RV120W Manual de instrucciones

Cisco

Cisco 515E - PIX Restricted Bundle Manual de usuario

Cisco

Cisco 5505 - ASA Firewall Edition Bundle Manual de usuario

Cisco

Cisco 5505 - ASA Firewall Edition Bundle Manual

Cisco

Cisco Cisco ASA Series Instrucciones de instalación

Cisco

Cisco ASA 5512-X Manual de usuario

Cisco

Cisco Firepower 3500 Documento técnico

Cisco

Cisco PIX-525-UR-BUN - PIX 525 Unrestricted Bundle Manual de usuario

Cisco

Cisco ASA 5506-X Manual de usuario

Cisco

Cisco ASA 5580 Manual de usuario

Cisco

Cisco PIX-515E Manual de usuario

Cisco

Cisco ASA 5555-X Manual de usuario

Cisco

Cisco MX400 Manual de usuario

Cisco

Cisco C690 Manual de usuario

Cisco

Cisco Small Business RV215W Manual de usuario

Cisco

Cisco Small Business RV220W Manual de usuario

Cisco

Cisco Cisco ASA Series Manual de usuario

Cisco

Cisco RV110W Manual de usuario

Cisco

Cisco 5505 - ASA Firewall Edition Bundle Manual de usuario

Cisco

Cisco Firepower 4100 Series Manual de instalación

Cisco

Cisco 5510 - ASA SSL / IPsec VPN Edition Manual de usuario

Cisco

Cisco ASA 5506-X Guía de inicio rápido

Cisco

Cisco ISA 3000 Manual de usuario

Cisco

Cisco 2100 Series Manual de usuario

Manuales populares de Cortafuegos de otras marcas

Fortinet

Fortinet FortiGate Voice Series Manual de usuario

ADTRAN

ADTRAN NetVanta 2300 Manual de usuario

SecureLogix

SecureLogix ETM System Manual de usuario

NETGEAR

NETGEAR ProSafe FVX538 Manual de usuario

Lanner

Lanner FW-8877 Manual de usuario

Huawei

Huawei USG6000 Series Manual de instalación y operación

H3C

H3C SecPath F5000-AI-15 Manual de usuario

Nexcom

Nexcom DNA 1150 Manual de usuario

Fortinet

Fortinet FortiGate-60 series Manual de usuario

Draytek

Draytek Vigor2860 Series Manual de usuario

Lanner electronics

Lanner electronics FW-7650 Series Manual de usuario

Swisscom

Swisscom Internet Backup Manual de usuario

SonicWALL

SonicWALL NSa 5700 Manual de usuario

DPtech

DPtech FW1000 SERIES Manual de usuario

FEITIAN

FEITIAN MultiPass FIDO Manual de usuario

EBLOCKER

EBLOCKER PRO Manual de usuario

GTA

GTA GB-200 Manual de usuario

Trend Micro

Trend Micro Deep Edge Manual de usuario