Cisco ASA 5506-X Instrucciones de instalación

Mount the Chassis

Do not remove the rubber feet included with the ASA because they are needed for proper cooling for all

mounting orientations.

Note

•Desktop-Mount the Chassis, on page 1

•Wall-Mount the Chassis, on page 2

•Rack-Mount the Chassis, on page 3

•Install the ASA 5506H-X in a DIN Rail, on page 8

Desktop-Mount the Chassis

You can mount the chassis on a desktop by placing it on a desk in a horizontal position. Make sure there are

no blockages or obstructions within one inch of the top of the chassis or within .5 inch of the sides and back,

so that nothing interferes with cooling. Do not remove the rubber feet included with the chassis. They are also

needed for proper cooling.

Do not stack the chassis on top of another chassis. If you stack the units, they will overheat, which causes the

units to power cycle.

Caution

Mount the Chassis

Wall-Mount the Chassis

Follow these steps to mount the chassis on a wall. You can purchase a wall-mount kit. The part number for

the wall-mount kit is ASA5506-WALL-MNT= .

Step 1 Choose a location on the wall for the chassis.

Step 2 Use the two Cisco-provided screws and anchors from the optional wall-mount kit.

If you are mounting the chassis onto something other than drywall, such as wood or sheet metal, anchors may not be

required.

Step 3 Use a pencil, ruler, and level to mark locations for the two mounting screws.

The width and length of the chassis are 7.87 x 9.23 inches ( 20 x 23.44 cm). The mounting holes in the chassis are in the

middle length-wise (that is, 6.372 inches from front and back), while the holes are inset from the opposite edges 0.75

inches (1.9 cm).

Thus, you need to make two level marks 6.37, or approximately 6-3/8, inches (16.18 cm) apart.

Figure 1: Marking the Locations of the Two Mounting Screws

Step 4 Drill a hole into the wall at each mark.

These holes should be slightly smaller in diameter than your anchors. The recommended drill hole size is 3/16".

Step 5 Insert the anchors into the holes and be sure they are properly seated.

Step 6 Fasten each screw into its anchor until it protrudes about 1/4 inch.

Step 7 Pick up the chassis, align the screws in the anchors with the holes in the bottom of the chassis, move the chassis toward

the wall until the screw heads are in the chassis, and then slide the chassis down until it rests on the screws.

Mount the Chassis

Wall-Mount the Chassis

You can only mount the chassis with the front panel oriented toward either the ceiling or the floor. Wall mounting in

other orientation is not supported.

What to do next

Install the cables as described in Quick Start Guide for your default software configuration.

Rack-Mount the Chassis

The rack-shelf kit (part number 800-107605-01) contains the following items:

There are two sets of four screws that you can use to secure the chassis to your rack. Chose the screws that

fit your rack.

Note

• Rack shelf (part number 700-122662-01)

• Sliding rack tray (part number 800-107648-01)

• Two cable guides (part number 700-122664-01)

• Six Phillips M3 x 0.5 x 10 mm screws (part number 48-0796-01); use these screws to install the cable

guides.

• Six Phillips M3 x 6 mm screws (part number 48-0384-01); use these screws to secure the rack shelf onto

the chassis.

• Four Phillips 12-24 x 0.75 inch screws (part number 48-0440-01); use these screws to secure the

sliding-rack tray to your rack.

• Four Phillips 10-32 x 0.75 inch screws (part number 48-0441-01); use these screws to secure the

sliding-rack tray to your rack.

You mount only one ASA 5506H-X in the rack-mount shelf.

The dimensions of the ASA 5506H-X are 3.46 x 18.3 x 19.5 inches (8.79 x 46.48 x 49.52 cm). The PID is

asa5506h-rack-mnt=.

Note

Step 1 Install the cable guides on the sliding rack tray:

Mount the Chassis

Rack-Mount the Chassis

Figure 2: Attach Cable Guides to Sliding-Rack Tray Flange

Left cable guide rack tray cutoutsTwo cable guides (part number 700-122664-01)1

Six Phillips M3 x 0.5 x 10 mm screws (part number

48-0796-01)

4Right cable guide rack tray cutouts3

a) Align the cable guides with the cutouts on the sliding-rack tray flange (see figure above).

b) At the rear of the sliding-rack tray, attach the left and right cable guides using the six Phillips M3 x 0.5 x 10 mm

screws (part number 48-0796-01).

Drive the screws in while facing the back of the sliding-rack tray.

Note

c) Set the sliding-rack tray aside. Continue with Step 2 to install the rack shelf on the chassis.

The figure in Step 8 shows the sliding rack tray with the cable guides attached.

Step 2 Place the chassis with the top facing down on a large, stable work area.

Step 3 Invert the rack shelf and position it on the chassis. You can mount the chassis with the front or rear panel facing front.

Mount the Chassis

Rack-Mount the Chassis

Figure 3: Install the Rack Shelf on the Chassis

Three short black screws M3 x 6 mm (part number

48-0384-01)

Step 4 Adjust the position of the chassis and the rack shelf until the three mounting holes in the dimples in the bottom of the

shelf are aligned with the mounting holes in the bottom of the chassis.

Step 5 Tighten the screws to lock the chassis into place on the rack shelf.

Make sure you are using the short black screws (M3 x 6 mm), otherwise you will damage the chassis.

Caution

Step 6 Carefully turn the rack shelf right-side up.

Step 7 Install the power supply on the rack shelf behind the chassis.

Mount the Chassis

Rack-Mount the Chassis

Figure 4: Install the Power Supply in the Rack Shelf

Velcro straps for power supply2Velcro straps for power supply1

Power supply stop4Power supply stop3

—Rear sliding stop and screw (one of two screws on the

sliding stop)

a) Loosen the Velcro straps and place the power supply on the rack shelf behind the chassis.

Make sure the AC inlet cord faces the rear.

b) Align the power supply to the side and rear stops.

If the rear sliding stop is not touching the power supply, loosen the two screws, slide the stop up to touch the power

supply, and then retighten screws.

c) Re-engage the Velcro straps and tighten them to secure the power supply.

Mount the Chassis

Rack-Mount the Chassis

Figure 5: Tighten the Velcro Straps

Velcro straps tightened over power supply1

Step 8 Slide the rack shelf into the sliding-rack tray.

Figure 6: Slide the Rack Shelf into the Sliding-Rack Tray

Step 9 The chassis is now installed in the rack shelf, which is installed in the sliding-rack tray. Repeat Steps 1 through 8 to

install a second chassis.

Mount the Chassis

Rack-Mount the Chassis

Figure 7: Completed Rack Shelf/Tray Installation

Step 10 Install the sliding-rack tray into your rack using the correct screws (12-24 x 0.75 inch or 10-32 x 0.75 inch) from the

rack-mount kit that fit your rack type.

What to do next

Install the cables according to your default software configuration as described in the Cisco ASA 5506-X

Series Quick Start Guide.

Install the ASA 5506H-X in a DIN Rail

You can use the 7.5 mm thick 45 mm wide top hat DIN rail for the ASA 5506H-X. Secure the DIN rail to the

mounting surface approximately every 7.8 inches (200 mm) and use end-anchors appropriately.

We recommend that you install the ASA 5506H-X on a steel DIN rail for extra stability.

Note

To attach the ASA 5506H-X to a 35 mm wide DIN rail, follow these steps:

Step 1 Attach the DIN rail bracket to the back of the chassis using the four screws provided.

Mount the Chassis

Install the ASA 5506H-X in a DIN Rail

Figure 8: Attach the DIN Rail Bracket to the ASA 5506H-X

Step 2 Locate the plastic tab on the end of the DIN rail bracket that extends past the chassis. Press the tab in and slide the plastic

latch piece out while the tab is pressed down to put it into the locked position.

Step 3 Turn the chassis sideways so that the power connector is near the top.

Step 4 Position the rear edge of the chassis directly in front of the DIN rail making sure that the DIN rail fits in the space between

the plastic latch and the metal hook.

Step 5 Position the chassis so that the hook on the DIN rail bracket hooks onto the top edge of the DIN rail. The weight of the

chassis can rest on the hook temporarily while the DIN rail bracket latches are secured.

Step 6 Push the DIN rail bracket latch up when the chassis is over the DIN rail to secure it. This snaps the latch into the closed

position which locks it onto the DIN rail.

Mount the Chassis

Install the ASA 5506H-X in a DIN Rail

Figure 9: ASA 5506H-X Installed with the DIN Rail

The chassis is now installed in the DIN rail.

What to do next

Install the cables as described in the Cisco ASA 5506-X Series Quick Start Guide.

Mount the Chassis

Install the ASA 5506H-X in a DIN Rail

Otros manuales para ASA 5506-X

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Cortafuegos de Cisco

Cisco

Cisco PIX-515E Manual de usuario

Cisco

Cisco Small Business RV220W Manual de instrucciones

Cisco

Cisco M690 Manual de usuario

Cisco

Cisco ASA 5580 Manual de usuario

Cisco

Cisco amp threat grid Manual de usuario

Cisco

Cisco FPR1010-ASA-K9 Manual de usuario

Cisco

Cisco RV120W Manual de instrucciones

Cisco

Cisco ASA 5585-X Manual de usuario

Cisco

Cisco M195 Manual

Cisco

Cisco Small Business RV215W Manual de usuario

Cisco

Cisco RV110W Manual de usuario

Cisco

Cisco CSA 90 Series Manual del producto

Cisco

Cisco Cisco ASA Series Manual de usuario

Cisco

Cisco RV120W Manual de instrucciones

Cisco

Cisco ASA 5506-X Guía de inicio rápido

Cisco

Cisco PIX 501 Manual

Cisco

Cisco 5505 - ASA Firewall Edition Bundle Manual de usuario

Cisco

Cisco IronPort M1070 Manual de usuario

Cisco

Cisco C690 Manual de usuario

Cisco

Cisco ASA 5508-X Manual de usuario

Cisco

Cisco 881W - Integrated Services Router Wireless Manual de instrucciones

Cisco

Cisco ASA 5555-X Manual de usuario

Cisco

Cisco RV120W Manual de usuario

Cisco

Cisco Cisco ASA Series Instrucciones de instalación

Manuales populares de Cortafuegos de otras marcas

Fortinet

Fortinet FortiGate Voice Series Manual de usuario

ADTRAN

ADTRAN NetVanta 2300 Manual de usuario

SecureLogix

SecureLogix ETM System Manual de usuario

NETGEAR

NETGEAR ProSafe FVX538 Manual de usuario

Lanner

Lanner FW-8877 Manual de usuario

Huawei

Huawei USG6000 Series Manual de instalación y operación

H3C

H3C SecPath F5000-AI-15 Manual de usuario

Nexcom

Nexcom DNA 1150 Manual de usuario

Fortinet

Fortinet FortiGate-60 series Manual de usuario

Draytek

Draytek Vigor2860 Series Manual de usuario

Lanner electronics

Lanner electronics FW-7650 Series Manual de usuario

Swisscom

Swisscom Internet Backup Manual de usuario

SonicWALL

SonicWALL NSa 5700 Manual de usuario

DPtech

DPtech FW1000 SERIES Manual de usuario

FEITIAN

FEITIAN MultiPass FIDO Manual de usuario

EBLOCKER

EBLOCKER PRO Manual de usuario

GTA

GTA GB-200 Manual de usuario

Trend Micro

Trend Micro Deep Edge Manual de usuario