Cisco C170 Manual de usuario
303357
1
0
1
0
Cisco C170
Email
Security
Appliance
QUICK START GUIDE
Cisco C170 Email Security Appliance
1Welcome
2Before You Begin
3Document Network Settings
4Plan the Installation
5Install the Appliance in a Rack
6Plug In the Appliance
7Temporarily Change Your IP Address
8Connect to the Appliance
9Power Up the Appliance
10 Log In to the Appliance
11 Run the System Setup Wizard
12 Run the Active Directory Wizard (Optional)
13 Configure Network Settings
14 Configuration Summary
15 You’re Done!
16 Where to Go from Here
C170_QSG.fm Page 1 Wednesday, March 13, 2013 9:31 PM
2
Revised: March 13, 2013
Part Number: 78-19640-04
1 Welcome
Thank you for choosing the Cisco C170 Email Security
Appliance (Cisco C170).
The Cisco C170 appliance is designed to serve as your SMTP
email gateway at your network perimeter—that is, the first
appliance with an IP address that is directly accessible to the
Internet for sending and receiving email. Many of the features
(including reputation filtering, data loss prevention, content
scanning, spam detection, and virus protection) require you to
install the Cisco appliance into your existing network
infrastructure.
This guide describes how to physically install your Cisco C170
appliance and use the System Setup Wizard to configure basic
settings.
C170_QSG.fm Page 2 Wednesday, March 13, 2013 9:31 PM
3
2 Before You Begin
Before you begin the installation, make sure that you have the
items needed.
The following items are included with the Cisco C170 Email
Security Appliance:
• Quick Start Guide (this guide)
• Rails and adaptor kit
• Power cable(s)
• Ethernet cable for connecting the appliance to your
network
• Regulatory Safety and Compliance Information
You will need to provide the following items yourself:
• Rack cabinet enclosure (if rack-mounting the appliance)
• Phillips-head screwdriver for assembling rails
• 10/100 Gigabit Base-T TCP/IP LAN
• Desktop or laptop computer
• Web browser (or SSH and terminal software)
• Network and administrator information for the “Document
Network Settings” section on page 4 and “go live”
configuration
C170_QSG.fm Page 3 Wednesday, March 13, 2013 9:31 PM
4
3 Document Network Settings
Before you begin, write down the following information about
your network and administrator settings.
System Settings
Default System Hostname:
Email System Alerts To:
Deliver Scheduled Reports To:
Time Zone Information:
NTP Server:
Admin Password:
SenderBase Network Participation: Enable/Disable
AutoSupport: Enable/Disable
Network Integration
Default Gateway (router) IP Address:
DNS (Internet or specify own):
Interfaces
P1
IP Address:
Network Mask:
Fully Qualified Hostname:
Accept Incoming Mail Domain:
Accept Incoming Mail Destination:
Relay Outgoing Mail:
P2
IP Address:
Network Mask:
Fully Qualified Hostname:
Accept Incoming Mail Domain:
Accept Incoming Mail Destination:
Relay Outgoing Mail:
Message Security
SenderBase Reputation Filtering: Enable/Disable
Cisco Anti-Spam Scanning Engine: Enable/Disable
McAfee Anti-Virus Scanning Engine: Enable/Disable
Sophos Anti-Virus Scanning Engine: Enable/Disable
Virus Outbreak Filters: Enable/Disable
C170_QSG.fm Page 4 Wednesday, March 13, 2013 9:31 PM
5
4 Plan the Installation
To defend your email system against spam, viruses, phishing,
and other threats, the Cisco C170 appliance must be installed at
the perimeter of your network. It needs to be the first appliance
with an IP address that can access the Internet.
Plan for your network configuration to look something like this:
Firewall or Router
Cisco C170
Mail Server
Clients
303354
1
7
0
0
r
0
1
0
1
0
Cisco C170
Email
Security
Appliance
C170_QSG.fm Page 5 Wednesday, March 13, 2013 9:31 PM
6
5 Install the Appliance in a Rack
Install the Cisco C170 Email Security Appliance using either the
slide rails or fixed rack mount brackets. For information about
these installation options, see the Cisco 170 Series Hardware
Installation Guide.
Appliance Placement in a Rack
• Ambient Temperature—To prevent the appliance from
overheating, do not operate it in an area that exceeds an
ambient temperature of 104°F (40°C).
• Air Flow—Be sure that there is adequate air flow around
the appliance.
• Mechanical Loading—Be sure that the appliance is level
and stable to avoid any hazardous conditions.
1
0
1
0
CiscoC170
Web
Security
Appliance
50
104
F
C
40
10
303363
Temperature Limits
C170_QSG.fm Page 6 Wednesday, March 13, 2013 9:31 PM
7
6 Plug In the Appliance
Plug the female end of the power cable into the power supply on
the back panel of the appliance. Plug the male end into an
electrical outlet.
7JZ78-004E
P1 P2CONSOLE
303358
Plug the C170 power cable
into an electrical outlet.
C170_QSG.fm Page 7 Wednesday, March 13, 2013 9:31 PM
8
7 Temporarily Change Your IP
Address
To connect to the Cisco C170 appliance, you must temporarily
change the IP address of your computer.
Note Make a note of your current IP configuration settings
because you will need to revert to these settings after
you finish the configuration.
For Windows
Step 1 Go to the Start menu and choose Control Panel.
Step 2 Double-click Network and Sharing Center.
Step 3 Click Local Area Connection and then click Properties.
Step 4 Select Internet Protocol (TCP/IP) and then click
Properties.
Step 5 Select Use the Following IP Address.
Step 6 Enter the following changes:
• IP Address: 192.168.42.43
• Subnet Mask: 255.255.255.0
• Default Gateway: 192.168.42.1
Step 7 Click OK and Close to exit the dialog box.
C170_QSG.fm Page 8 Wednesday, March 13, 2013 9:31 PM
9
For Mac
Step 1 Launch the Apple menu and choose System Preferences.
Step 2 Click Network.
Step 3 Select the network configuration with the green icon.
This is your active connection. Then click Advanced.
Step 4 Click the TCP/IP tab and from Ethernet settings,
choose Manually from the drop-down list.
Step 5 Enter the following changes:
• IP Address: 192.168.42.43
• Subnet Mask: 255.255.255.0
• Router: 192.168.42.1
Step 6 Click OK.
C170_QSG.fm Page 9 Wednesday, March 13, 2013 9:31 PM
10
8 Connect to the Appliance
The Cisco C170 appliance has two gigabit network ports:
P1 and P2. At least one static IP address is required to send and
receive email.
You can receive and deliver email from a single connection to
either network port if your network topology dictates it. Two IP
addresses can be configured on one network interface.
Or, you can connect the P1 network port to your public network
and connect the P2 network port to your private network.
To access the appliance by Ethernet, connect to P1 as your
management interface and configure incoming email on P2.
Or, for serial access to the appliance, connect to the console
port.
7JZ78-004E
P1 P2CONSOLE
P1 P2
P1:
Management: 192.168.42.42
Connect the P1 port
to your computer using
an Ethernet cable.
P2:
Incoming Email
Connect the P2 port
to your network using
an Ethernet cable.
303356
C170_QSG.fm Page 10 Wednesday, March 13, 2013 9:31 PM
Tabla de contenidos
Otros manuales de Cortafuegos de Cisco
Cisco
Cisco Cisco ASA Series Manual de usuario
Cisco
Cisco 380 Series Manual
Cisco
Cisco CSA 90 Series Manual del producto
Cisco
Cisco MEREAKI MX65W Manual de usuario
Cisco
Cisco C690 Manual de usuario
Cisco
Cisco PIX 506 - Firewall Manual de usuario
Cisco
Cisco Small Business Pro SA 520W Manual de instrucciones
Cisco
Cisco 5505 - ASA Firewall Edition Bundle Manual de usuario
Cisco
Cisco LightStream 1010 Manual de usuario
Cisco
Cisco FPR1010-ASA-K9 Manual de usuario
Cisco
Cisco Firepower 1010 Manual de usuario
Cisco
Cisco ASA 5512-X Manual de usuario
Cisco
Cisco TelePresence Server 7010 Manual de usuario
Cisco
Cisco RV120W Manual de instrucciones
Cisco
Cisco S190 Manual de usuario
Cisco
Cisco 881W - Integrated Services Router Wireless Manual de instrucciones
Cisco
Cisco Firepower 1100 Series Manual
Cisco
Cisco PIX 501 Manual
Cisco
Cisco ASA 5580 Manual de usuario
Cisco
Cisco LightStream 1010 Instrucciones de instalación
Manuales populares de Cortafuegos de otras marcas
H3C
H3C SecPath F5000-AI-15 Manual de usuario
Nexcom
Nexcom DNA 1150 Manual de usuario
Fortinet
Fortinet FortiGate-60 series Manual de usuario
Draytek
Draytek Vigor2860 Series Manual de usuario
Lanner electronics
Lanner electronics FW-7650 Series Manual de usuario
Swisscom
Swisscom Internet Backup Manual de usuario
